#ifndef __LCD_CONFIG_H__
#define __LCD_CONFIG_H__

typedef	unsigned char LCDBYTE;			//重定義有關LCD的,也即LCD當中的數據位寬
typedef unsigned char DOTBYTE;			//重定義有關LCD的,也即LCD的點陣數量
typedef signed short  DISWORD;			//重定義在LCD_Dis.c文件中一些中間處理的數據的寬度

typedef unsigned char FLASH;	//重定義驅動當中存放到CODE的數據類型聲明
#ifndef NULL
#define NULL    ((void *)0)
#endif

#ifndef FALSE
#define FALSE   (0)
#endif

#ifndef TRUE
#define TRUE    (1)
#endif

typedef unsigned char  BYTE;
typedef unsigned short WORD;
typedef unsigned long  DWORD;
typedef unsigned int   BOOL;

#define LCD_X_MAX			128-1			//屏幕的X軸的物理寬度
#define LCD_Y_MAX			64-1			//屏幕的Y軸的物理寬度
			
#define LCD_XY_Switch		0				//顯示時X軸和Y由交換
#define LCD_X_Rev			0				//顯示時X軸反轉
#define LCD_Y_Rev			0				//顯示時Y軸反轉

#if LCD_XY_Switch == 0
	#define Dis_X_MAX		LCD_X_MAX
	#define Dis_Y_MAX		LCD_Y_MAX	
#endif

#if LCD_XY_Switch == 1
	#define Dis_X_MAX		LCD_Y_MAX
	#define Dis_Y_MAX		LCD_X_MAX	
#endif

#define LCD_INITIAL_COLOR	0x00			//定義LCD屏初始化時的背景色

//以下定義為針對于SPLC501的功能指令進行定義的，局部可修改~
//LCD供電電平選擇
#define		M_LCD_VDD_SET	M_LCD_SETR_4		//3.3V供電時選此二項
#define		M_LCD_VDD		M_LCD_BIAS_9		//....
//#define		M_LCD_VDD_SET	M_LCD_SETR_4	//5.0V供電時選此二項
//#define		M_LCD_VDD		M_LCD_BIAS_9	//...
//LCD指令
//LCD開關命令
#define		M_LCD_ON		0xaf
#define		M_LCD_OFF		0xae
//設置上電控制模式
#define		M_LCD_POWER_BC	0x2c
#define		M_LCD_POWER_VR	0x2a
#define		M_LCD_POWER_VC	0x29
#define		M_LCD_POWER_ALL	0x2f
//V5內部電壓調節電阻設置……
#define		M_LCD_SETR_0	0x20
#define		M_LCD_SETR_1	0x21
#define		M_LCD_SETR_2	0x22
#define		M_LCD_SETR_3	0x23
#define		M_LCD_SETR_4	0x24
#define		M_LCD_SETR_5	0x25
#define		M_LCD_SETR_6	0x26
#define		M_LCD_SETR_7	0x27
//...end
#define		M_LCD_ELE_VOL	0x81		//電量設置模式（顯示亮度）
//偏壓設置
#define		M_LCD_BIAS_9	0xa2		//V5時選此選項設置
#define		M_LCD_BIAS_7	0xa1		//V3時選此選項設置
//Com 掃描方式設置命令
#define		M_LCD_COM_NOR	0xc0		//正常方式
#define		M_LCD_COM_REV	0xc8		//反相
//Segment方向選擇
#define		M_LCD_SEG_NOR	0xa0		//正常
#define		M_LCD_SEG_REV	0xa1		//反向
//全屏點亮/變暗指令
#define		M_LCD_ALL_LIGNT	0xa5		//LCD ALL paint ON
#define		M_LCD_ALL_LOW	0xa4		//Normal Display mode
//正相反相顯示控制指令，RAM中數據不變
#define		M_LCD_ALL_NOR	0xa6		//正相
#define		M_LCD_ALL_REV	0xa7		//反相
//靜態指示器控制指令
#define		M_LCD_STATIC_ON	0xad		//ON
#define		M_LCD_STATIC_OFF 0xac		//OFF
//設置顯示起始行對應RAM行號
#define		M_LCD_BEGIN_LINE 0x40		//基數，后面可加的尾數可為0~63
//設置當前頁基數
#define		M_LCD_COL_PAGE	0xb0		//基數指令，后可加尾數0~8
//設置當前列基數
#define		M_LCD_COL_LINE_LOW	0x04		//基數指令，低四位有效
#define		M_LCD_COL_LINE_HIG	0x10		//基數指令，低四位有效
#endif