;******************************************************************************
;   MSP-FET430P140 Demo - USART0, UART 115200 Echo ISR, HF XTAL ACLK
;
;   Description: Echo a received character, RX ISR used. Normal mode is LPM0,
;   USART0 RX interrupt triggers TX Echo. Though not required, MCLK = LFXT1
;   ACLK = MCLK = UCLK0 = LFXT1 = 8MHz
;   Baud rate divider with 8MHz XTAL @115k = 8000000/115200 = 0069
;   //* USART0 interrupt flags are in different SFR's from MSP430F14x/13x *//
;   //* An external 8MHz XTAL on XIN XOUT is required for ACLK *//
;   //* Min Vcc required varies with MCLK frequency - refer to datasheet *//		
;
;
;                MSP430F149
;             -----------------
;         /|\|              XIN|-
;          | |                 | 8MHz
;          --|RST          XOUT|-
;            |                 |
;            |             P3.4|------------>
;            |                 | 115200 - 8N1
;            |             P3.5|<------------
;
;   M. Buccini
;   Texas Instruments Inc.
;   Feb 2005
;   Built with IAR Embedded Workbench Version: 3.21A
;******************************************************************************
#include  <msp430x14x.h>
;------------------------------------------------------------------------------
            ORG     01100h                  ; Progam Start
;------------------------------------------------------------------------------
RESET       mov.w   #0A00h,SP               ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop WDT
SetupP3     bis.b   #030h,&P3SEL            ; P3.4,5 = USART0 TXD/RXD
SetupBC     bis.b   #XTS,&BCSCTL1           ; LFXT1 = HF XTAL
SetupOsc    bic.b   #OFIFG,&IFG1            ; Clear OSC fault flag
            mov.w   #0FFh,R15               ; R15 = Delay
SetupOsc1   dec.w   R15                     ; Additional delay to ensure start
            jnz     SetupOsc1               ;
            bit.b   #OFIFG,&IFG1            ; OSC fault flag set?
            jnz     SetupOsc                ; OSC Fault, clear flag again
            bis.b   #SELM_3,&BCSCTL2        ; MCLK = LFXT1
SetupUART0  bis.b   #UTXE0+URXE0,&ME1       ; Enable USART0 TXD/RXD
            bis.b   #CHAR,&UCTL0            ; 8-bit characters
            mov.b   #SSEL0,&UTCTL0          ; UCLK = ACLK
            mov.b   #045h,&UBR00            ; 8MHz 115200
            mov.b   #000h,&UBR10            ; 8MHz 115200
            mov.b   #000h,&UMCTL0           ; 8MHz no modulation 115200
            bic.b   #SWRST,&UCTL0           ; **Initialize USART state machine**
            bis.b   #URXIE0,&IE1            ; Enable USART0 RX interrupt
                                            ;
Mainloop    bis.b   #CPUOFF+GIE,SR          ; Enter LPM0, interrupts enabled
            nop                             ; Needed only for debugger
                                            ;
;------------------------------------------------------------------------------
USART0RX_ISR;  Confirm TX buffer is ready, then Echo back RXed character
;------------------------------------------------------------------------------
TX1         bit.b   #UTXIFG0,&IFG1          ; USART0 TX buffer ready?
            jz      TX1                     ; Jump is TX buffer not ready
            mov.b   &RXBUF0,&TXBUF0         ; TX -> RXed character
            reti                            ;
                                            ;
;------------------------------------------------------------------------------
;           Interrupt Vectors
;------------------------------------------------------------------------------
            ORG     0FFFEh                  ;
            DW      RESET                   ; POR, ext. Reset, Watchdog
            ORG     0FFF2h                  ;
            DW      USART0RX_ISR            ; USART0 receive
            END