#if 0           	        	/* Hidden receive FIFO bits        */#define SDDR_EOF	0x00000100	/*  receive End-Of-Frame (read)    */#define SDDR_CRE	0x00000200	/*  receive CRC Error (read)       */#define SDDR_ROR	0x00000400	/*  Receive FIFO Over-Run (read)   */#endif /* 0 */#define SDSR0_EIF	0x00000001	/* Error In FIFO (read)            */#define SDSR0_TUR	0x00000002	/* Transmit FIFO Under-Run         */#define SDSR0_RAB	0x00000004	/* Receive ABort                   */#define SDSR0_TFS	0x00000008	/* Transmit FIFO 1/2-full or less  */                	        	/* Service request (read)          */#define SDSR0_RFS	0x00000010	/* Receive FIFO 1/3-to-2/3-full or */                	        	/* more Service request (read)     */#define SDSR1_RSY	0x00000001	/* Receiver SYnchronized (read)    */#define SDSR1_TBY	0x00000002	/* Transmitter BusY (read)         */#define SDSR1_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */#define SDSR1_TNF	0x00000008	/* Transmit FIFO Not Full (read)   */#define SDSR1_RTD	0x00000010	/* Receive Transition Detected     */#define SDSR1_EOF	0x00000020	/* receive End-Of-Frame (read)     */#define SDSR1_CRE	0x00000040	/* receive CRC Error (read)        */#define SDSR1_ROR	0x00000080	/* Receive FIFO Over-Run (read)    *//* * High-Speed Serial to Parallel controller (HSSP) control registers * * Registers *    Ser2HSCR0 	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Control Register 0 (read/write). *    Ser2HSCR1 	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Control Register 1 (read/write). *    Ser2HSDR  	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Data Register (read/write). *    Ser2HSSR0 	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Status Register 0 (read/write). *    Ser2HSSR1 	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Status Register 1 (read). *    Ser2HSCR2 	Serial port 2 High-Speed Serial to Parallel *              	controller (HSSP) Control Register 2 (read/write). *              	[The HSCR2 register is only implemented in *              	versions 2.0 (rev. = 8) and higher of the StrongARM *              	SA-1100.] */#define Ser2HSCR0	__REG(0x80040060)  /* Ser. port 2 HSSP Control Reg. 0 */#define Ser2HSCR1	__REG(0x80040064)  /* Ser. port 2 HSSP Control Reg. 1 */#define Ser2HSDR	__REG(0x8004006C)  /* Ser. port 2 HSSP Data Reg.      */#define Ser2HSSR0	__REG(0x80040074)  /* Ser. port 2 HSSP Status Reg. 0  */#define Ser2HSSR1	__REG(0x80040078)  /* Ser. port 2 HSSP Status Reg. 1  */#define Ser2HSCR2	__REG(0x90060028)  /* Ser. port 2 HSSP Control Reg. 2 */#define HSCR0_ITR	0x00000001	/* IrDA Transmission Rate          */#define HSCR0_UART	(HSCR0_ITR*0)	/*  UART mode (115.2 kb/s if IrDA) */#define HSCR0_HSSP	(HSCR0_ITR*1)	/*  HSSP mode (4 Mb/s)             */#define HSCR0_LBM	0x00000002	/* Look-Back Mode                  */#define HSCR0_TUS	0x00000004	/* Transmit FIFO Under-run Select  */#define HSCR0_EFrmURn	(HSCR0_TUS*0)	/*  End Frame on Under-Run         */#define HSCR0_AbortURn	(HSCR0_TUS*1)	/*  Abort on Under-Run             */#define HSCR0_TXE	0x00000008	/* Transmit Enable                 */#define HSCR0_RXE	0x00000010	/* Receive Enable                  */#define HSCR0_RIE	0x00000020	/* Receive FIFO 2/5-to-3/5-full or */                	        	/* more Interrupt Enable           */#define HSCR0_TIE	0x00000040	/* Transmit FIFO 1/2-full or less  */                	        	/* Interrupt Enable                */#define HSCR0_AME	0x00000080	/* Address Match Enable            */#define HSCR1_AMV	Fld (8, 0)	/* Address Match Value             */#define HSDR_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */#if 0           	        	/* Hidden receive FIFO bits        */#define HSDR_EOF	0x00000100	/*  receive End-Of-Frame (read)    */#define HSDR_CRE	0x00000200	/*  receive CRC Error (read)       */#define HSDR_ROR	0x00000400	/*  Receive FIFO Over-Run (read)   */#endif /* 0 */#define HSSR0_EIF	0x00000001	/* Error In FIFO (read)            */#define HSSR0_TUR	0x00000002	/* Transmit FIFO Under-Run         */#define HSSR0_RAB	0x00000004	/* Receive ABort                   */#define HSSR0_TFS	0x00000008	/* Transmit FIFO 1/2-full or less  */                	        	/* Service request (read)          */#define HSSR0_RFS	0x00000010	/* Receive FIFO 2/5-to-3/5-full or */                	        	/* more Service request (read)     */#define HSSR0_FRE	0x00000020	/* receive FRaming Error           */#define HSSR1_RSY	0x00000001	/* Receiver SYnchronized (read)    */#define HSSR1_TBY	0x00000002	/* Transmitter BusY (read)         */#define HSSR1_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */#define HSSR1_TNF	0x00000008	/* Transmit FIFO Not Full (read)   */#define HSSR1_EOF	0x00000010	/* receive End-Of-Frame (read)     */#define HSSR1_CRE	0x00000020	/* receive CRC Error (read)        */#define HSSR1_ROR	0x00000040	/* Receive FIFO Over-Run (read)    */#define HSCR2_TXP	0x00040000	/* Transmit data Polarity (TXD_2)  */#define HSCR2_TrDataL	(HSCR2_TXP*0)	/*  Transmit Data active Low       */                	        	/*  (inverted)                     */#define HSCR2_TrDataH	(HSCR2_TXP*1)	/*  Transmit Data active High      */                	        	/*  (non-inverted)                 */#define HSCR2_RXP	0x00080000	/* Receive data Polarity (RXD_2)   */#define HSCR2_RcDataL	(HSCR2_RXP*0)	/*  Receive Data active Low        */                	        	/*  (inverted)                     */#define HSCR2_RcDataH	(HSCR2_RXP*1)	/*  Receive Data active High       */                	        	/*  (non-inverted)                 *//* * Multi-media Communications Port (MCP) control registers * * Registers *    Ser4MCCR0 	Serial port 4 Multi-media Communications Port (MCP) *              	Control Register 0 (read/write). *    Ser4MCDR0 	Serial port 4 Multi-media Communications Port (MCP) *              	Data Register 0 (audio, read/write). *    Ser4MCDR1 	Serial port 4 Multi-media Communications Port (MCP) *              	Data Register 1 (telecom, read/write). *    Ser4MCDR2 	Serial port 4 Multi-media Communications Port (MCP) *              	Data Register 2 (CODEC registers, read/write). *    Ser4MCSR  	Serial port 4 Multi-media Communications Port (MCP) *              	Status Register (read/write). *    Ser4MCCR1 	Serial port 4 Multi-media Communications Port (MCP) *              	Control Register 1 (read/write). *              	[The MCCR1 register is only implemented in *              	versions 2.0 (rev. = 8) and higher of the StrongARM *              	SA-1100.] * * Clocks *    fmc, Tmc  	Frequency, period of the MCP communication (10 MHz, *              	12 MHz, or GPIO [21]). *    faud, Taud	Frequency, period of the audio sampling. *    ftcm, Ttcm	Frequency, period of the telecom sampling. */#define Ser4MCCR0	__REG(0x80060000)  /* Ser. port 4 MCP Control Reg. 0 */#define Ser4MCDR0	__REG(0x80060008)  /* Ser. port 4 MCP Data Reg. 0 (audio) */#define Ser4MCDR1	__REG(0x8006000C)  /* Ser. port 4 MCP Data Reg. 1 (telecom) */#define Ser4MCDR2	__REG(0x80060010)  /* Ser. port 4 MCP Data Reg. 2 (CODEC reg.) */#define Ser4MCSR	__REG(0x80060018)  /* Ser. port 4 MCP Status Reg. */#define Ser4MCCR1	__REG(0x90060030)  /* Ser. port 4 MCP Control Reg. 1 */#define MCCR0_ASD	Fld (7, 0)	/* Audio Sampling rate Divisor/32  */                	        	/* [6..127]                        */                	        	/* faud = fmc/(32*ASD)             */                	        	/* Taud = 32*ASD*Tmc               */#define MCCR0_AudSmpDiv(Div)    	/*  Audio Sampling rate Divisor    */ \                	        	/*  [192..4064]                    */ \                	((Div)/32 << FShft (MCCR0_ASD))                	        	/*  faud = fmc/(32*Floor (Div/32)) */                	        	/*  Taud = 32*Floor (Div/32)*Tmc   */#define MCCR0_CeilAudSmpDiv(Div)	/*  Ceil. of AudSmpDiv [192..4064] */ \                	(((Div) + 31)/32 << FShft (MCCR0_ASD))                	        	/*  faud = fmc/(32*Ceil (Div/32))  */                	        	/*  Taud = 32*Ceil (Div/32)*Tmc    */#define MCCR0_TSD	Fld (7, 8)	/* Telecom Sampling rate           */                	        	/* Divisor/32 [16..127]            */                	        	/* ftcm = fmc/(32*TSD)             */                	        	/* Ttcm = 32*TSD*Tmc               */#define MCCR0_TcmSmpDiv(Div)    	/*  Telecom Sampling rate Divisor  */ \                	        	/*  [512..4064]                    */ \                	((Div)/32 << FShft (MCCR0_TSD))                	        	/*  ftcm = fmc/(32*Floor (Div/32)) */                	        	/*  Ttcm = 32*Floor (Div/32)*Tmc   */#define MCCR0_CeilTcmSmpDiv(Div)	/*  Ceil. of TcmSmpDiv [512..4064] */ \                	(((Div) + 31)/32 << FShft (MCCR0_TSD))                	        	/*  ftcm = fmc/(32*Ceil (Div/32))  */                	        	/*  Ttcm = 32*Ceil (Div/32)*Tmc    */#define MCCR0_MCE	0x00010000	/* MCP Enable                      */#define MCCR0_ECS	0x00020000	/* External Clock Select           */#define MCCR0_IntClk	(MCCR0_ECS*0)	/*  Internal Clock (10 or 12 MHz)  */#define MCCR0_ExtClk	(MCCR0_ECS*1)	/*  External Clock (GPIO [21])     */#define MCCR0_ADM	0x00040000	/* A/D (audio/telecom) data        */                	        	/* sampling/storing Mode           */#define MCCR0_VldBit	(MCCR0_ADM*0)	/*  Valid Bit storing mode         */#define MCCR0_SmpCnt	(MCCR0_ADM*1)	/*  Sampling Counter storing mode  */#define MCCR0_TTE	0x00080000	/* Telecom Transmit FIFO 1/2-full  */                	        	/* or less interrupt Enable        */#define MCCR0_TRE	0x00100000	/* Telecom Receive FIFO 1/2-full   */                	        	/* or more interrupt Enable        */#define MCCR0_ATE	0x00200000	/* Audio Transmit FIFO 1/2-full    */                	        	/* or less interrupt Enable        */#define MCCR0_ARE	0x00400000	/* Audio Receive FIFO 1/2-full or  */                	        	/* more interrupt Enable           */#define MCCR0_LBM	0x00800000	/* Look-Back Mode                  */#define MCCR0_ECP	Fld (2, 24)	/* External Clock Prescaler - 1    */#define MCCR0_ExtClkDiv(Div)    	/*  External Clock Divisor [1..4]  */ \                	(((Div) - 1) << FShft (MCCR0_ECP))#define MCDR0_DATA	Fld (12, 4)	/* receive/transmit audio DATA     */                	        	/* FIFOs                           */#define MCDR1_DATA	Fld (14, 2)	/* receive/transmit telecom DATA   */                	        	/* FIFOs                           */                	        	/* receive/transmit CODEC reg.     */                	        	/* FIFOs:                          */#define MCDR2_DATA	Fld (16, 0)	/*  reg. DATA                      */#define MCDR2_RW	0x00010000	/*  reg. Read/Write (transmit)     */#define MCDR2_Rd	(MCDR2_RW*0)	/*   reg. Read                     */#define MCDR2_Wr	(MCDR2_RW*1)	/*   reg. Write                    */#define MCDR2_ADD	Fld (4, 17)	/*  reg. ADDress                   */#define MCSR_ATS	0x00000001	/* Audio Transmit FIFO 1/2-full    */                	        	/* or less Service request (read)  */#define MCSR_ARS	0x00000002	/* Audio Receive FIFO 1/2-full or  */                	        	/* more Service request (read)     */#define MCSR_TTS	0x00000004	/* Telecom Transmit FIFO 1/2-full  */                	        	/* or less Service request (read)  */#define MCSR_TRS	0x00000008	/* Telecom Receive FIFO 1/2-full   */                	        	/* or more Service request (read)  */#define MCSR_ATU	0x00000010	/* Audio Transmit FIFO Under-run   */#define MCSR_ARO	0x00000020	/* Audio Receive FIFO Over-run     */#define MCSR_TTU	0x00000040	/* Telecom Transmit FIFO Under-run */#define MCSR_TRO	0x00000080	/* Telecom Receive FIFO Over-run   */#define MCSR_ANF	0x00000100	/* Audio transmit FIFO Not Full    */                	        	/* (read)                          */#define MCSR_ANE	0x00000200	/* Audio receive FIFO Not Empty    */                	        	/* (read)                          */#define MCSR_TNF	0x00000400	/* Telecom transmit FIFO Not Full  */                	        	/* (read)                          */#define MCSR_TNE	0x00000800	/* Telecom receive FIFO Not Empty  */                	        	/* (read)                          */#define MCSR_CWC	0x00001000	/* CODEC register Write Completed  */                	        	/* (read)                          */#define MCSR_CRC	0x00002000	/* CODEC register Read Completed   */                	        	/* (read)                          */#define MCSR_ACE	0x00004000	/* Audio CODEC Enabled (read)      */#define MCSR_TCE	0x00008000	/* Telecom CODEC Enabled (read)    */#define MCCR1_CFS	0x00100000	/* Clock Freq. Select              */#define MCCR1_F12MHz	(MCCR1_CFS*0)	/*  Freq. (fmc) = ~ 12 MHz         */                	        	/*  (11.981 MHz)                   */#define MCCR1_F10MHz	(MCCR1_CFS*1)	/*  Freq. (fmc) = ~ 10 MHz         */                	        	/*  (9.585 MHz)                    *//* * Synchronous Serial Port (SSP) control registers * * Registers *    Ser4SSCR0 	Serial port 4 Synchronous Serial Port (SSP) Control *              	Register 0 (read/write). *    Ser4SSCR1 	Serial port 4 Synchronous Serial Port (SSP) Control *              	Register 1 (read/write). *              	[Bits SPO and SP are only implemented in versions 2.0