//*****************************************************************************
//  MSP430x47x4 Demo - SD16, Continuous Conversion on a Group of 4 Channels
//
//  Description: This program uses the SD16 module to perform continuous
//  conversions on a group of channels (0, 1,2 and 3). A SD16 interrupt occurs
//  whenever the conversions have completed. Test by applying voltages to the
//  four input channels and setting a breakpoint at the line indicated
//  below. Run program until it reaches the breakpoint, then use
//  the debugger's watch window to view the conversion results. Results
//  (upper 16 bits only) are stored in three arrays, one for each channel.
//  ACLK = LFXT1 = 32768 Hz, MCLK = SMCLK = DCO = 32 x ACLK = 1048576 Hz
//  //* An external watch crystal on XIN XOUT is required for ACLK     *//	
//  //* For minimum Vcc required for SD16 module - see datasheet       *//
//  //* 100nF cap btw Vref and AVss is recommended when using 1.2V ref *//
//
//                MSP430x47x4
//             -----------------
//         /|\|              XIN|-
//          | |                 | 32kHz
//          --|RST          XOUT|-
//            |                 |
//   Vin1+ -->|A0.0+            |
//   Vin1- -->|A0.0-            |
//   Vin2+ -->|A1.0+            |
//   Vin2- -->|A1.0-            |
//   Vin3+ -->|A2.0+            |
//   Vin3- -->|A2.0-            |
//   Vin4+ -->|A3.0+            |
//   Vin4- -->|A3.0-       VREF |---+
//            |                 |   |
//            |                 |  -+- 100nF
//            |                 |  -+-
//            |                 |   |
//            |            AVss |---+
//            |                 |
//
//  P. Thanigai / K.Venkat
//  Texas Instruments Inc.
//  November 2007
//  Built with CCE Version: 3.2.0 and IAR Embedded Workbench Version: 3.42A
//*****************************************************************************
#include  <msp430x47x4.h>

#define   Num_of_Results   8

/* Arrays to store SD16 conversion results */
unsigned int Ch0results[Num_of_Results];
unsigned int Ch1results[Num_of_Results];
unsigned int Ch2results[Num_of_Results];
unsigned int Ch3results[Num_of_Results];

void main(void)
{
  volatile unsigned int i;                  // Use volatile to prevent removal
                                            // by compiler optimization

  WDTCTL = WDTPW + WDTHOLD;                 // Stop WDT
  FLL_CTL0 |= XCAP14PF;                     // Configure load caps
  for (i = 0; i < 10000; i++);              // Delay for 32 kHz crystal to
                                            // stabilize

  SD16CTL = SD16REFON + SD16SSEL0;          // 1.2V ref, SMCLK
  SD16CCTL0 |= SD16GRP;                     // Group with CH1
  SD16CCTL1 |= SD16GRP;                     // Group with CH2
  SD16CCTL2 |= SD16GRP;                     // Group with CH3
  SD16CCTL3 |= SD16IE;                      // Enable interrupt
  for (i = 0; i < 0x3600; i++);             // Delay for 1.2V ref startup
  
  SD16CCTL3 |= SD16SC;                      // Set bit to start conversion
  __bis_SR_register(LPM0_bits + GIE);       // Enter LPM0 w/ interrupts
}

#pragma vector=SD16A_VECTOR
__interrupt void SD16AISR(void)
{
  static unsigned int index = 0;

  switch (SD16IV)
  {
    case 2:                                   // SD16MEM Overflow
      break;
    case 4:                                   // SD16MEM0 IFG
      break;
    case 6:                                   // SD16MEM1 IFG
      break;
    case 8:                                   // SD16MEM2 IFG
      break;
    case 10:
      Ch0results[index] = SD16MEM0;           // Save CH0 results (clears IFG)
      Ch1results[index] = SD16MEM1;           // Save CH1 results (clears IFG)
      Ch2results[index] = SD16MEM2;           // Save CH2 results (clears IFG)
      Ch3results[index] = SD16MEM3;           // Save CH3 results (clears IFG)
      if(++index == Num_of_Results)
      {
        index = 0;                            // SET BREAKPOINT HERE
      }
      break;
  }
}