* Xmac/Broadcom/LevelOne/National-specific. * All other are general. *//*****  PHY_XMAC_CTRL	16 bit r/w	PHY Control Register *****//*****  PHY_BCOM_CTRL	16 bit r/w	PHY Control Register *****//*****  PHY_LONE_CTRL	16 bit r/w	PHY Control Register *****/#define PHY_CT_RESET	(1<<15)	/* Bit 15: (sc)	clear all PHY related regs */#define PHY_CT_LOOP		(1<<14)	/* Bit 14:	enable Loopback over PHY */#define PHY_CT_SPS_LSB	(1<<13) /* Bit 13: (BC,L1) Speed select, lower bit */#define PHY_CT_ANE		(1<<12)	/* Bit 12:	Auto-Negotiation Enabled */#define PHY_CT_PDOWN	(1<<11)	/* Bit 11: (BC,L1) Power Down Mode */#define PHY_CT_ISOL		(1<<10)	/* Bit 10: (BC,L1) Isolate Mode */#define PHY_CT_RE_CFG	(1<<9)	/* Bit  9: (sc) Restart Auto-Negotiation */#define PHY_CT_DUP_MD	(1<<8)	/* Bit  8:	Duplex Mode */#define PHY_CT_COL_TST	(1<<7)	/* Bit  7: (BC,L1) Collision Test enabled */#define PHY_CT_SPS_MSB	(1<<6)	/* Bit  6: (BC,L1) Speed select, upper bit */								/* Bit  5..0:	reserved */#define PHY_CT_SP1000	PHY_CT_SPS_MSB	/* enable speed of 1000 Mbps */#define PHY_CT_SP100	PHY_CT_SPS_LSB	/* enable speed of  100 Mbps */#define PHY_CT_SP10		(0)				/* enable speed of   10 Mbps *//*****  PHY_XMAC_STAT	16 bit r/w	PHY Status Register *****//*****  PHY_BCOM_STAT	16 bit r/w	PHY Status Register *****//*****  PHY_MARV_STAT	16 bit r/w	PHY Status Register *****//*****  PHY_LONE_STAT	16 bit r/w	PHY Status Register *****/								/* Bit 15..9:	reserved */				/*	(BC/L1) 100/10 Mbps cap bits ignored*/#define PHY_ST_EXT_ST	(1<<8)	/* Bit  8:	Extended Status Present */								/* Bit  7:	reserved */#define PHY_ST_PRE_SUP	(1<<6)	/* Bit  6: (BC/L1) preamble suppression */#define PHY_ST_AN_OVER	(1<<5)	/* Bit  5:	Auto-Negotiation Over */#define PHY_ST_REM_FLT	(1<<4)	/* Bit  4:	Remote Fault Condition Occured */#define PHY_ST_AN_CAP	(1<<3)	/* Bit  3:	Auto-Negotiation Capability */#define PHY_ST_LSYNC	(1<<2)	/* Bit  2:	Link Synchronized */#define PHY_ST_JAB_DET	(1<<1)	/* Bit  1: (BC/L1) Jabber Detected */#define PHY_ST_EXT_REG	(1<<0)	/* Bit  0:	Extended Register available *//*****	PHY_XMAC_ID1		16 bit r/o	PHY ID1 Register *//*****	PHY_BCOM_ID1		16 bit r/o	PHY ID1 Register *//*****	PHY_MARV_ID1		16 bit r/o	PHY ID1 Register *//*****	PHY_LONE_ID1		16 bit r/o	PHY ID1 Register */#define PHY_I1_OUI_MSK	(0x3f<<10)	/* Bit 15..10:	Organization Unique ID */#define PHY_I1_MOD_NUM	(0x3f<<4)	/* Bit  9.. 4:	Model Number */#define PHY_I1_REV_MSK	0x0f		/* Bit  3.. 0:	Revision Number *//* different Broadcom PHY Ids */#define PHY_BCOM_ID1_A1		0x6041#define PHY_BCOM_ID1_B2		0x6043#define PHY_BCOM_ID1_C0		0x6044#define PHY_BCOM_ID1_C5		0x6047/*****  PHY_XMAC_AUNE_ADV	16 bit r/w	Auto-Negotiation Advertisement *****//*****  PHY_XMAC_AUNE_LP	16 bit r/o	Link Partner Ability Reg *****/#define PHY_AN_NXT_PG	(1<<15)	/* Bit 15:	Request Next Page */#define PHY_X_AN_ACK	(1<<14)	/* Bit 14: (ro)	Acknowledge Received */#define PHY_X_AN_RFB	(3<<12)	/* Bit 13..12:	Remote Fault Bits */								/* Bit 11.. 9:	reserved */#define PHY_X_AN_PAUSE	(3<<7)	/* Bit  8.. 7:	Pause Bits */#define PHY_X_AN_HD		(1<<6)	/* Bit  6:	Half Duplex */#define PHY_X_AN_FD		(1<<5)	/* Bit  5:	Full Duplex */								/* Bit  4.. 0:	reserved *//*****  PHY_BCOM_AUNE_ADV	16 bit r/w	Auto-Negotiation Advertisement *****//*****  PHY_BCOM_AUNE_LP	16 bit r/o	Link Partner Ability Reg *****//*	PHY_AN_NXT_PG		(see XMAC) Bit 15:	Request Next Page */								/* Bit 14:	reserved */#define PHY_B_AN_RF		(1<<13)	/* Bit 13:	Remote Fault */								/* Bit 12:	reserved */#define PHY_B_AN_ASP	(1<<11)	/* Bit 11:	Asymmetric Pause */#define PHY_B_AN_PC		(1<<10)	/* Bit 10:	Pause Capable */								/* Bit  9..5:	100/10 BT cap bits ingnored */#define PHY_B_AN_SEL	0x1f	/* Bit 4..0:	Selector Field, 00001=Ethernet*//*****  PHY_LONE_AUNE_ADV	16 bit r/w	Auto-Negotiation Advertisement *****//*****  PHY_LONE_AUNE_LP	16 bit r/o	Link Partner Ability Reg *****//*	PHY_AN_NXT_PG		(see XMAC) Bit 15:	Request Next Page */								/* Bit 14:	reserved */#define PHY_L_AN_RF		(1<<13)	/* Bit 13:	Remote Fault */								/* Bit 12:	reserved */#define PHY_L_AN_ASP	(1<<11)	/* Bit 11:	Asymmetric Pause */#define PHY_L_AN_PC		(1<<10)	/* Bit 10:	Pause Capable */								/* Bit  9..5:	100/10 BT cap bits ingnored */#define PHY_L_AN_SEL	0x1f	/* Bit 4..0:	Selector Field, 00001=Ethernet*//*****  PHY_NAT_AUNE_ADV	16 bit r/w	Auto-Negotiation Advertisement *****//*****  PHY_NAT_AUNE_LP		16 bit r/o	Link Partner Ability Reg *****//*	PHY_AN_NXT_PG		(see XMAC) Bit 15:	Request Next Page */								/* Bit 14:	reserved */#define PHY_N_AN_RF		(1<<13)	/* Bit 13:	Remote Fault */								/* Bit 12:	reserved */#define PHY_N_AN_100F	(1<<11)	/* Bit 11:	100Base-T2 FD Support */#define PHY_N_AN_100H	(1<<10)	/* Bit 10:	100Base-T2 HD Support */								/* Bit  9..5:	100/10 BT cap bits ingnored */#define PHY_N_AN_SEL	0x1f	/* Bit 4..0:	Selector Field, 00001=Ethernet*//* field type definition for PHY_x_AN_SEL */#define PHY_SEL_TYPE	0x01	/* 00001 = Ethernet *//*****  PHY_XMAC_AUNE_EXP	16 bit r/o	Auto-Negotiation Expansion Reg *****/								/* Bit 15..4:	reserved */#define PHY_AN_LP_NP	(1<<3)	/* Bit  3:	Link Partner can Next Page */#define PHY_AN_LOC_NP	(1<<2)	/* Bit  2:	Local PHY can Next Page */#define PHY_AN_RX_PG	(1<<1)	/* Bit  1:	Page Received */								/* Bit  0:	reserved *//*****  PHY_BCOM_AUNE_EXP	16 bit r/o	Auto-Negotiation Expansion Reg *****/								/* Bit 15..5:	reserved */#define PHY_B_AN_PDF	(1<<4)	/* Bit  4:	Parallel Detection Fault *//*	PHY_AN_LP_NP		(see XMAC) Bit  3:	Link Partner can Next Page *//*	PHY_AN_LOC_NP		(see XMAC) Bit  2:	Local PHY can Next Page *//*	PHY_AN_RX_PG		(see XMAC) Bit  1:	Page Received */#define PHY_B_AN_LP_CAP	(1<<0)	/* Bit  0:	Link Partner Auto-Neg. Cap. *//*****  PHY_LONE_AUNE_EXP	16 bit r/o	Auto-Negotiation Expansion Reg *****/#define PHY_L_AN_BP		(1<<5)	/* Bit  5:	Base Page Indication */#define PHY_L_AN_PDF	(1<<4)	/* Bit  4:	Parallel Detection Fault *//*	PHY_AN_LP_NP		(see XMAC) Bit  3:	Link Partner can Next Page *//*	PHY_AN_LOC_NP		(see XMAC) Bit  2:	Local PHY can Next Page *//*	PHY_AN_RX_PG		(see XMAC) Bit  1:	Page Received */#define PHY_B_AN_LP_CAP	(1<<0)	/* Bit  0:	Link Partner Auto-Neg. Cap. *//*****  PHY_XMAC_NEPG		16 bit r/w	Next Page Register *****//*****  PHY_BCOM_NEPG		16 bit r/w	Next Page Register *****//*****  PHY_LONE_NEPG		16 bit r/w	Next Page Register *****//*****  PHY_XMAC_NEPG_LP	16 bit r/o	Next Page Link Partner *****//*****  PHY_BCOM_NEPG_LP	16 bit r/o	Next Page Link Partner *****//*****  PHY_LONE_NEPG_LP	16 bit r/o	Next Page Link Partner *****/#define PHY_NP_MORE		(1<<15)	/* Bit 15:	More, Next Pages to follow */#define PHY_NP_ACK1		(1<<14)	/* Bit 14: (ro)	Ack 1, for receiving a message*/#define PHY_NP_MSG_VAL	(1<<13)	/* Bit 13:	Message Page valid */#define PHY_NP_ACK2		(1<<12)	/* Bit 12:	Ack 2, comply with msg content*/#define PHY_NP_TOG		(1<<11)	/* Bit 11:	Toggle Bit, ensure sync */#define PHY_NP_MSG		0x07ff	/* Bit 10..0:	Message from/to Link Partner *//* * XMAC-Specific *//*****  PHY_XMAC_EXT_STAT	16 bit r/w	Extended Status Register *****/#define PHY_X_EX_FD		(1<<15)	/* Bit 15:	Device Supports Full Duplex */#define PHY_X_EX_HD		(1<<14)	/* Bit 14:	Device Supports Half Duplex */								/* Bit 13..0:	reserved *//*****  PHY_XMAC_RES_ABI	16 bit r/o	PHY Resolved Ability *****/								/* Bit 15..9:	reserved */#define PHY_X_RS_PAUSE	(3<<7)	/* Bit  8..7:	selected Pause Mode */#define PHY_X_RS_HD		(1<<6)	/* Bit  6:	Half Duplex Mode selected */#define PHY_X_RS_FD		(1<<5)	/* Bit  5:	Full Duplex Mode selected */#define PHY_X_RS_ABLMIS (1<<4)	/* Bit  4:	duplex or pause cap mismatch */#define PHY_X_RS_PAUMIS (1<<3)	/* Bit  3:	pause capability missmatch */								/* Bit  2..0:	reserved *//* * Remote Fault Bits (PHY_X_AN_RFB) encoding */#define X_RFB_OK		(0<<12)	/* Bit 13..12	No errors, Link OK */#define X_RFB_LF		(1<<12)	/* Bit 13..12	Link Failure */#define X_RFB_OFF		(2<<12)	/* Bit 13..12	Offline */#define X_RFB_AN_ERR	(3<<12)	/* Bit 13..12	Auto-Negotiation Error *//* * Pause Bits (PHY_X_AN_PAUSE and PHY_X_RS_PAUSE) encoding */#define PHY_X_P_NO_PAUSE	(0<<7)	/* Bit  8..7:	no Pause Mode */#define PHY_X_P_SYM_MD		(1<<7)	/* Bit  8..7:	symmetric Pause Mode */#define PHY_X_P_ASYM_MD		(2<<7)	/* Bit  8..7:	asymmetric Pause Mode */#define PHY_X_P_BOTH_MD		(3<<7)	/* Bit  8..7:	both Pause Mode *//* * Broadcom-Specific *//*****  PHY_BCOM_1000T_CTRL	16 bit r/w	1000Base-T Control Reg *****/#define PHY_B_1000C_TEST	(7<<13)	/* Bit 15..13:	Test Modes */#define PHY_B_1000C_MSE		(1<<12)	/* Bit 12:	Master/Slave Enable */#define PHY_B_1000C_MSC		(1<<11)	/* Bit 11:	M/S Configuration */#define PHY_B_1000C_RD		(1<<10)	/* Bit 10:	Repeater/DTE */#define PHY_B_1000C_AFD		(1<<9)	/* Bit  9:	Advertise Full Duplex */#define PHY_B_1000C_AHD		(1<<8)	/* Bit  8:	Advertise Half Duplex */									/* Bit  7..0:	reserved *//*****  PHY_BCOM_1000T_STAT	16 bit r/o	1000Base-T Status Reg *****/#define PHY_B_1000S_MSF		(1<<15)	/* Bit 15:	Master/Slave Fault */#define PHY_B_1000S_MSR		(1<<14)	/* Bit 14:	Master/Slave Result */#define PHY_B_1000S_LRS		(1<<13)	/* Bit 13:	Local Receiver Status */#define PHY_B_1000S_RRS		(1<<12)	/* Bit 12:	Remote Receiver Status */#define PHY_B_1000S_LP_FD	(1<<11)	/* Bit 11:	Link Partner can FD */#define PHY_B_1000S_LP_HD	(1<<10)	/* Bit 10:	Link Partner can HD */									/* Bit  9..8:	reserved */#define PHY_B_1000S_IEC		0xff	/* Bit  7..0:	Idle Error Count *//*****  PHY_BCOM_EXT_STAT	16 bit r/o	Extended Status Register *****/#define PHY_B_ES_X_FD_CAP	(1<<15)	/* Bit 15:	1000Base-X FD capable */#define PHY_B_ES_X_HD_CAP	(1<<14)	/* Bit 14:	1000Base-X HD capable */#define PHY_B_ES_T_FD_CAP	(1<<13)	/* Bit 13:	1000Base-T FD capable */#define PHY_B_ES_T_HD_CAP	(1<<12)	/* Bit 12:	1000Base-T HD capable */									/* Bit 11..0:	reserved *//*****  PHY_BCOM_P_EXT_CTRL	16 bit r/w	PHY Extended Control Reg *****/#define PHY_B_PEC_MAC_PHY	(1<<15)	/* Bit 15:	10BIT/GMI-Interface */#define PHY_B_PEC_DIS_CROSS	(1<<14)	/* Bit 14:	Disable MDI Crossover */#define PHY_B_PEC_TX_DIS	(1<<13)	/* Bit 13:	Tx output Disabled */#define PHY_B_PEC_INT_DIS	(1<<12)	/* Bit 12:	Interrupts Disabled */#define PHY_B_PEC_F_INT		(1<<11)	/* Bit 11:	Force Interrupt */#define PHY_B_PEC_BY_45		(1<<10)	/* Bit 10:	Bypass 4B5B-Decoder */#define PHY_B_PEC_BY_SCR	(1<<9)	/* Bit  9:	Bypass Scrambler */#define PHY_B_PEC_BY_MLT3	(1<<8)	/* Bit  8:	Bypass MLT3 Encoder */#define PHY_B_PEC_BY_RXA	(1<<7)	/* Bit  7:	Bypass Rx Alignm. */#define PHY_B_PEC_RES_SCR	(1<<6)	/* Bit  6:	Reset Scrambler */#define PHY_B_PEC_EN_LTR	(1<<5)	/* Bit  5:	Ena LED Traffic Mode */#define PHY_B_PEC_LED_ON	(1<<4)	/* Bit  4:	Force LED's on */#define PHY_B_PEC_LED_OFF	(1<<3)	/* Bit  3:	Force LED's off */#define PHY_B_PEC_EX_IPG	(1<<2)	/* Bit  2:	Extend Tx IPG Mode */#define PHY_B_PEC_3_LED		(1<<1)	/* Bit  1:	Three Link LED mode */#define PHY_B_PEC_HIGH_LA	(1<<0)	/* Bit  0:	GMII FIFO Elasticy *//*****  PHY_BCOM_P_EXT_STAT	16 bit r/o	PHY Extended Status Reg *****/									/* Bit 15..14:	reserved */#define PHY_B_PES_CROSS_STAT	(1<<13)	/* Bit 13:	MDI Crossover Status */#define PHY_B_PES_INT_STAT	(1<<12)	/* Bit 12:	Interrupt Status */#define PHY_B_PES_RRS		(1<<11)	/* Bit 11:	Remote Receiver Stat. */#define PHY_B_PES_LRS		(1<<10)	/* Bit 10:	Local Receiver Stat. */#define PHY_B_PES_LOCKED	(1<<9)	/* Bit  9:	Locked */#define PHY_B_PES_LS		(1<<8)	/* Bit  8:	Link Status */#define PHY_B_PES_RF		(1<<7)	/* Bit  7:	Remote Fault */#define PHY_B_PES_CE_ER		(1<<6)	/* Bit  6:	Carrier Ext Error */#define PHY_B_PES_BAD_SSD	(1<<5)	/* Bit  5:	Bad SSD */#define PHY_B_PES_BAD_ESD	(1<<4)	/* Bit  4:	Bad ESD */#define PHY_B_PES_RX_ER		(1<<3)	/* Bit  3:	Receive Error */#define PHY_B_PES_TX_ER		(1<<2)	/* Bit  2:	Transmit Error */#define PHY_B_PES_LOCK_ER	(1<<1)	/* Bit  1:	Lock Error */#define PHY_B_PES_MLT3_ER	(1<<0)	/* Bit  0:	MLT3 code Error *//*****  PHY_BCOM_FC_CTR		16 bit r/w	False Carrier Counter *****/									/* Bit 15..8:	reserved */#define PHY_B_FC_CTR		0xff	/* Bit  7..0:	False Carrier Counter *//*****  PHY_BCOM_RNO_CTR	16 bit r/w	Receive NOT_OK Counter *****/#define PHY_B_RC_LOC_MSK	0xff00	/* Bit 15..8:	Local Rx NOT_OK cnt */#define PHY_B_RC_REM_MSK	0x00ff	/* Bit  7..0:	Remote Rx NOT_OK cnt *//*****  PHY_BCOM_AUX_CTRL	16 bit r/w	Auxiliary Control Reg *****/#define PHY_B_AC_L_SQE		(1<<15)	/* Bit 15:	Low Squelch */#define PHY_B_AC_LONG_PACK	(1<<14)	/* Bit 14:	Rx Long Packets */#define PHY_B_AC_ER_CTRL	(3<<12)	/* Bit 13..12:	Edgerate Control */									/* Bit 11:	reserved */#define PHY_B_AC_TX_TST		(1<<10) /* Bit 10:	Tx test bit, always 1 */									/* Bit  9.. 8:	reserved */#define PHY_B_AC_DIS_PRF	(1<<7)	/* Bit  7:	dis part resp filter */									/* Bit  6:	reserved */#define PHY_B_AC_DIS_PM		(1<<5)	/* Bit  5:	dis power management */									/* Bit  4:	reserved */#define PHY_B_AC_DIAG		(1<<3)	/* Bit  3:	Diagnostic Mode */									/* Bit  2.. 0:	reserved *//*****  PHY_BCOM_AUX_STAT	16 bit r/o	Auxiliary Status Reg *****/#define PHY_B_AS_AN_C		(1<<15)	/* Bit 15:	AutoNeg complete */#define PHY_B_AS_AN_CA		(1<<14)	/* Bit 14:	AN Complete Ack */#define PHY_B_AS_ANACK_D	(1<<13)	/* Bit 13:	AN Ack Detect */#define PHY_B_AS_ANAB_D		(1<<12)	/* Bit 12:	AN Ability Detect */#define PHY_B_AS_NPW		(1<<11)	/* Bit 11:	AN Next Page Wait */#define PHY_B_AS_AN_RES_MSK	(7<<8)	/* Bit 10..8:	AN HDC */#define PHY_B_AS_PDF		(1<<7)	/* Bit  7:	Parallel Detect. Fault */