//******************************************************************************
//  MSP430x24x Demo - Flash In-System Programming w/ EEI, Copy SegC to SegD
//
//  Description: This program first erases flash seg C, then it increments all
//  values in seg C, then it erases seg D, then copies seg C to seg D.
//  The EEI bit (Interrupts during segment erase enabled) is set for the Flash 
//  Erase Cycles. This does allow the Timer_AInterrupts to be handled also 
//  during the Segment erase time. Starting  addresses of segments defined in
//  this code: Seg C-0x1040, Seg D-0x1000.
//  ACLK = n/a, MCLK = SMCLK = CALxxx_1MHZ = 1MHz
//  //* Set Breakpoint on NOP in the Mainloop to avoid Stressing Flash *//
//
//               MSP430F249
//            -----------------
//        /|\|              XIN|-
//         | |                 |
//         --|RST          XOUT|-
//           |                 |
//
//  B. Nisarga
//  Texas Instruments Inc.
//  September 2007
//  Built with IAR Embedded Workbench Version: 3.42A
//******************************************************************************
#include "msp430x24x.h"

char value;                                 // 8-bit value to write to seg C

// Function prototypes
void write_SegC(char value);
void copy_C2D(void);

void main(void)
{
  WDTCTL = WDTPW + WDTHOLD;                 // Stop watchdog timer
  BCSCTL1 = CALBC1_1MHZ;                    // Set DCO to 1MHz
  DCOCTL = CALDCO_1MHZ;
  FCTL2 = FWKEY + FSSEL0 + FN1;             // MCLK/3 for Flash Timing Generator
  P1DIR |= 0x01;                            // P1.0 output
  TACCTL0 = CCIE;                           // TACCR0 interrupt enabled
  TACCR0 = 50000;
  TACTL = TASSEL_2 + MC_1;                  // SMCLK, upmode
  value = 0;                                // initialize value
  __enable_interrupt();                     // enable interrupts

  while(1)                                  // Repeat forever
  {
    write_SegC(value++);                    // Write segment C, increment value
    copy_C2D();                             // Copy segment C to D
    __no_operation();                       // SET BREAKPOINT HERE
  }
}

void write_SegC(char value)
{
  char *Flash_ptr;                          // Flash pointer
  unsigned int i;

  Flash_ptr = (char *)0x1040;               // Initialize Flash pointer
  FCTL3 = FWKEY;                            // Clear Lock bit
  FCTL1 = FWKEY + ERASE + EEI;              // Set Erase bit, allow interrupts
  *Flash_ptr = 0;                           // Dummy write to erase Flash seg

  FCTL1 = FWKEY + WRT;                      // Set WRT bit for write operation

  for (i = 0; i < 64; i++)
  {
    *Flash_ptr++ = value;                   // Write value to flash
  }

  FCTL1 = FWKEY;                            // Clear WRT bit
  FCTL3 = FWKEY + LOCK;                     // Set LOCK bit
}

void copy_C2D(void)
{
  char *Flash_ptrC;                         // Segment C pointer
  char *Flash_ptrD;                         // Segment D pointer
  unsigned int i;

  Flash_ptrC = (char *)0x1040;              // Initialize Flash segment C ptr
  Flash_ptrD = (char *)0x1000;              // Initialize Flash segment D ptr
  FCTL1 = FWKEY + ERASE + EEI;              // Set Erase bit, allow interrupts
  FCTL3 = FWKEY;                            // Clear Lock bit
  *Flash_ptrD = 0;                          // Dummy write to erase Flash seg D
  FCTL1 = FWKEY + WRT;                      // Set WRT bit for write operation

  for (i = 0; i < 64; i++)
  {
    *Flash_ptrD++ = *Flash_ptrC++;          // copy value segment C to seg D
  }

  FCTL1 = FWKEY;                            // Clear WRT bit
  FCTL3 = FWKEY + LOCK;                     // Set LOCK bit
}

// Timer A0 interrupt service routine
#pragma vector = TIMERA0_VECTOR
__interrupt void Timer_A(void)
{
  P1OUT ^= 0x01;                            // Toggle P1.0
}