/* * Configuation settings for the BuS EB+MCF-EV123 boards. * * (C) Copyright 2005 BuS Elektronik GmbH & Co.KG <esw@bus-elektonik.de> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */#ifndef _CONFIG_EB_MCF_EV123_H_#define _CONFIG_EB_MCF_EV123_H_#define  CONFIG_EB_MCF_EV123#undef DEBUG#undef CFG_HALT_BEFOR_RAM_JUMP#undef ET_DEBUG/* * High Level Configuration Options (easy to change) */#define	CONFIG_MCF52x2			/* define processor family */#define CONFIG_M5282			/* define processor type */#define CONFIG_MISC_INIT_R#define CONFIG_MCFUART#define CFG_UART_PORT		(0)#define CONFIG_BAUDRATE 9600#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }#undef	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */#define CONFIG_BOOTCOMMAND "printenv"/* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */#ifndef CONFIG_MONITOR_IS_IN_RAM#define CFG_ENV_ADDR		0xF003C000	/* End of 256K */#define CFG_ENV_SECT_SIZE	0x4000#define CFG_ENV_IS_IN_FLASH	1/*#define CFG_ENV_IS_EMBEDDED	1#define CFG_ENV_ADDR_REDUND		0xF0018000#define CFG_ENV_SECT_SIZE_REDUND	0x4000*/#else#define CFG_ENV_ADDR		0xFFE04000#define CFG_ENV_SECT_SIZE	0x2000#define CFG_ENV_IS_IN_FLASH	1#endif/* * BOOTP options */#define CONFIG_BOOTP_BOOTFILESIZE#define CONFIG_BOOTP_BOOTPATH#define CONFIG_BOOTP_GATEWAY#define CONFIG_BOOTP_HOSTNAME/* * Command line configuration. */#include <config_cmd_default.h>#undef CONFIG_CMD_LOADB#define CONFIG_CMD_MII#define CONFIG_CMD_NET#define CONFIG_MCFFEC#ifdef CONFIG_MCFFEC#	define CONFIG_NET_MULTI		1#	define CONFIG_MII		1#	define CFG_DISCOVER_PHY#	define CFG_RX_ETH_BUFFER	8#	define CFG_FAULT_ECHO_LINK_DOWN#	define CFG_FEC0_PINMUX		0#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE#	define MCFFEC_TOUT_LOOP 	50000/* If CFG_DISCOVER_PHY is not defined - hardcoded */#	ifndef CFG_DISCOVER_PHY#		define FECDUPLEX	FULL#		define FECSPEED		_100BASET#	else#		ifndef CFG_FAULT_ECHO_LINK_DOWN#			define CFG_FAULT_ECHO_LINK_DOWN#		endif#	endif			/* CFG_DISCOVER_PHY */#endif#ifdef CONFIG_MCFFEC#	define CONFIG_ETHADDR	00:CF:52:82:EB:01#	define CONFIG_IPADDR	192.162.1.2#	define CONFIG_NETMASK	255.255.255.0#	define CONFIG_SERVERIP	192.162.1.1#	define CONFIG_GATEWAYIP	192.162.1.1#	define CONFIG_OVERWRITE_ETHADDR_ONCE#endif				/* CONFIG_MCFFEC */#define CONFIG_BOOTDELAY	5#define CFG_PROMPT		"\nEV123 U-Boot> "#define	CFG_LONGHELP				/* undef to save memory		*/#if defined(CONFIG_CMD_KGDB)#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/#else#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/#endif#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */#define	CFG_MAXARGS		16		/* max number of command args	*/#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/#define CFG_LOAD_ADDR		0x20000#define CFG_MEMTEST_START	0x100000#define CFG_MEMTEST_END		0x400000/*#define CFG_DRAM_TEST		1 */#undef CFG_DRAM_TEST/* Clock and PLL Configuration */#define CFG_HZ			10000000#define	CFG_CLK			58982400       /* 9,8304MHz * 6 *//* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */#define CFG_MFD			0x01	/* PLL Multiplication Factor Devider */#define CFG_RFD			0x00	/* PLL Reduce Frecuency Devider *//* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */#define	CFG_MBAR		0x40000000/*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */#define CFG_INIT_RAM_ADDR       0x20000000#define CFG_INIT_RAM_END	0x10000		/* End of used area in internal SRAM	*/#define CFG_GBL_DATA_SIZE	64      	/* size in bytes reserved for initial data */#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET/*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CFG_SDRAM_BASE _must_ start at 0 */#define CFG_SDRAM_BASE1		0x00000000#define	CFG_SDRAM_SIZE1		16		/* SDRAM size in MB *//*#define CFG_SDRAM_BASE0		CFG_SDRAM_BASE1+CFG_SDRAM_SIZE1*1024*1024#define	CFG_SDRAM_SIZE0		16	*/	/* SDRAM size in MB */#define CFG_SDRAM_BASE		CFG_SDRAM_BASE1#define	CFG_SDRAM_SIZE		CFG_SDRAM_SIZE1#define CFG_FLASH_BASE		0xFFE00000#define	CFG_INT_FLASH_BASE	0xF0000000#define CFG_INT_FLASH_ENABLE	0x21/* If M5282 port is fully implemented the monitor base will be behind * the vector table. */#if (TEXT_BASE !=  CFG_INT_FLASH_BASE)#define CFG_MONITOR_BASE	(TEXT_BASE + 0x400)#else#define CFG_MONITOR_BASE	(TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */#endif#define CFG_MONITOR_LEN		0x20000#define CFG_MALLOC_LEN		(256 << 10)#define CFG_BOOTPARAMS_LEN	64*1024/* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*//*----------------------------------------------------------------------- * FLASH organization */#define	CFG_MAX_FLASH_SECT	35#define	CFG_MAX_FLASH_BANKS	2#define	CFG_FLASH_ERASE_TOUT	10000000#define	CFG_FLASH_PROTECTION/*----------------------------------------------------------------------- * Cache Configuration */#define CFG_CACHELINE_SIZE	16/*----------------------------------------------------------------------- * Memory bank definitions */#define CFG_CS0_BASE		CFG_FLASH_BASE#define CFG_CS0_SIZE		2*1024*1024#define CFG_CS0_WIDTH		16#define CFG_CS0_RO 		0#define CFG_CS0_WS		6#define CFG_CS3_BASE		0xE0000000#define CFG_CS3_SIZE		1*1024*1024#define CFG_CS3_WIDTH		16#define CFG_CS3_RO 		0#define CFG_CS3_WS		6/*----------------------------------------------------------------------- * Port configuration */#define CFG_PACNT		0x0000000	/* Port A D[31:24] */#define CFG_PADDR		0x0000000#define CFG_PADAT		0x0000000#define CFG_PBCNT		0x0000000	/* Port B D[23:16] */#define CFG_PBDDR		0x0000000#define CFG_PBDAT		0x0000000#define CFG_PCCNT		0x0000000	/* Port C D[15:08] */#define CFG_PCDDR		0x0000000#define CFG_PCDAT		0x0000000#define CFG_PDCNT		0x0000000	/* Port D D[07:00] */#define CFG_PCDDR		0x0000000#define CFG_PCDAT		0x0000000#define CFG_PEHLPAR		0xC0#define CFG_PUAPAR		0x0F		/* UA0..UA3 = Uart 0 +1 */#define CFG_DDRUA		0x05#define CFG_PJPAR 		0xFF;/*----------------------------------------------------------------------- * CCM configuration */#define	CFG_CCM_SIZ		0/*---------------------------------------------------------------------*/#endif	/* _CONFIG_M5282EVB_H *//*---------------------------------------------------------------------*/