;******************************************************************************
;  MSP-FET430P140 Demo - DMA0/1/2, USART1 SPI 3-Wire Master P1.x Exchange
;
;  Description: SPI Master communicates at fast as possible, full-duplex with
;  SPI Slave using 3-wire mode. The level on P1.4/5 is TX'ed and RX'ed to P1.0
;  and P1.1. Master will pulse slave Reset on init to insure synch start.
;  With data transfer driven directly by DMA - no CPU resources used.
;  DMA0 trigger from TX read, which uses MPY to shift read P1 left
;  DMA1 trigger from MPY moves shifted P1 data to the USART1 TX buffer
;  DMA2 trigger from USART RX1 buffer moves received data to P1
;  Master mode is LPM0.
;  ACLK = n/a, MCLK = SMCLK = DCO ~ 800kHz, ULCK = external
;  //* Final Production MSP430F16x(x) Device Required *//
;
;              fet140_dma_15              fet140_dma_16
;              MSP430F169 Slave           MSP430F169 Master
;             -----------------          -----------------
;            |              XIN|-    /|\|              XIN|-
;            |                 |      | |                 |
;            |             XOUT|-     --|RST          XOUT|-
;            |                 | /|\    |                 |
;            |              RST|--+<----|P5.0             |
;      LED <-|P1.0             |        |             P1.4|<-
;      LED <-|P1.1             |        |             P1.5|<-
;          ->|P1.4             |        |             P1.0|-> LED
;          ->|P1.5             |        |             P1.1|-> LED
;            |       SIMO0/P3.1|<-------|P5.1/SIMO1       |
;            |       SOMI0/P3.2|------->|P5.2/SOMI1       |
;            |        UCLK/P3.3|<-------|P5.3/UCLK1       |
;
;
;   H. Grewal / A. Dannenberg
;   Texas Instruments Inc.
;   November 2005
;   Built with IAR Embedded Workbench Version: 3.30A
;******************************************************************************
#include  <msp430x16x.h>
;------------------------------------------------------------------------------
            ORG     01100h                  ; Progam Start
;------------------------------------------------------------------------------
RESET       mov.w   #0A00h,SP               ; Initialize stackpointer
StopWDT     mov.w   #WDTPW+WDTHOLD,&WDTCTL  ; Stop watchdog timer
            mov.b   #0h,&P1OUT              ; P1.0/1 setup for LED output
            mov.b   #03h,&P1DIR             ;
SetupP5     bis.b   #0Eh,&P5SEL             ; P5.1,2,3 SPI option select
            bic.b   #01h,&P5OUT
            bis.b   #01h,&P5DIR             ; Reset Slave with P5.0
            bic.b   #01h,&P5DIR             ;
SetupSPI1   bis.b   #CHAR+SYNC+MM+SWRST,&UCTL1 ; 8-bit SPI Master
            bis.b   #CKPL+SSEL1+STC,&UTCTL1 ; SMCLK, 3-pin
            mov.b   #02h,&UBR01             ; SMCLK/2 for baud rate
            clr.b   &UBR11                  ; SMCLK/2 for baud rate
            clr.b   &UMCTL1                 ; Clear modulation
            bis.b   #USPIE1,&ME2            ; Enable USART1 SPI
            bic.b   #SWRST,&UCTL1           ; **Initialize USART state machine**
            mov.w   #0FFFh,R15              ; Time for slave to ready
L$1         dec.w   R15                     ;
            jnz     L$1                     ;
            mov.w   #1000h,&MPY             ; MPY first operand
            mov.w   #DMA2TSEL_9+DMA1TSEL_11+DMA0TSEL_10,&DMACTL0 ; URXIFG1, MPY, UTXIFG1
RX_store    mov.w   #U1RXBUF_,&DMA2SA       ; Src address = UART RX Buffer
            mov.w   #P1OUT_,&DMA2DA         ; Dst address = P1
            mov.w   #01h,&DMA2SZ            ; Size in words
            mov.w   #DMADT_4+DMASBDB+DMAEN,&DMA2CTL ; Sng, config
TX_load     mov.w   #RESHI_,&DMA1SA         ; Src address = multiplier
            mov.w   #U1TXBUF_,&DMA1DA       ; Dst address = UART TX Buffer
            mov.w   #01h,&DMA1SZ            ; Size in words
            mov.w   #DMADT_4+DMASBDB+DMAEN,&DMA1CTL ; Sng, config
TX_Init     mov.w   #P1IN_,&DMA0SA          ; Src address
            mov.w   #OP2_,&DMA0DA           ; Dst address = multiplier
            mov.w   #01h,&DMA0SZ            ; Size in words
            mov.w   #DMADT_4+DMASBDB+DMALEVEL+DMAEN,&DMA0CTL ; Sng rpt, config
            bis.b   #LPM0+GIE,SR            ; Enter LPM0
;------------------------------------------------------------------------------
;           Interrupt Vectors
;------------------------------------------------------------------------------
            ORG     0FFFEh                  ; POR, ext. Reset, Watchdog, Flash
            DW      RESET                   ;
            END