?? at89s52.h
字號:
/*--------------------------------------------------------------------------
AT89S52.H
Header file for the Atmel AT89S52.
Copyright (c) 1988-2002 Keil Elektronik GmbH and Keil Software, Inc.
All rights reserved.
--------------------------------------------------------------------------*/
#ifndef __AT89S52_H__
#define __AT89S52_H__
/*------------------------------------------------
Byte Registers
Note: Only Registers located on addresses that
are evenly divisible by 8 are bit addressable.
All other registers use bit masks.
------------------------------------------------*/
sfr P0 = 0x80; /* Port 0 */
sfr SP = 0x81; /* Stack Pointer */
sfr DPL = 0x82; /* Data Pointer Low Byte */
sfr DP0L = 0x82; /* Alternate Definition */
sfr DPH = 0x83; /* Data Pointer High Byte */
sfr DP0H = 0x83; /* Alternate Definition */
sfr DP1L = 0x84; /* Data Pointer 1 Low Byte */
sfr DP1H = 0x85; /* Data Pointer 1 High Byte */
sfr PCON = 0x87; /* Power Control Register */
sfr TCON = 0x88; /* Timer Control Register */
sfr TMOD = 0x89; /* Timer Mode Control Register */
sfr TL0 = 0x8A; /* Timer 0 Low Byte */
sfr TL1 = 0x8B; /* Timer 1 Low Byte */
sfr TH0 = 0x8C; /* Timer 0 High Byte */
sfr TH1 = 0x8D; /* Timer 1 High Byte */
sfr AUXR = 0x8E; /* Auxiliary Register*/
sfr P1 = 0x90; /* Port 1 */
sfr SCON = 0x98; /* Serial Port Control */
sfr SBUF = 0x99; /* Serial Port Buffer */
sfr P2 = 0xA0; /* Port 2 */
sfr AUXR1 = 0xA2; /* Auxiliary Register1 */
sfr WDTRST = 0xA6; /* Watch Dog Timer Reset */
sfr IE = 0xA8; /* Interrupt Enable Register 0 */
sfr P3 = 0xB0; /* Port 3 */
sfr IP = 0xB8; /* Interrupt Priority Register */
sfr T2CON = 0xC8; /* Timer 2 Control */
sfr T2MOD = 0xC9; /* Timer 2 Mode */
sfr RCAP2L = 0xCA; /* Timer 2 Capture Low Byte */
sfr RCAP2H = 0xCB; /* Timer 2 Capture High Byte */
sfr TL2 = 0xCC; /* Timer 2 Low Byte */
sfr TH2 = 0xCD; /* Timer 2 High Byte */
sfr PSW = 0xD0; /* Program Status Word */
sfr ACC = 0xE0; /* Accumulator */
sfr B = 0xF0; /* B Register */
/*------------------------------------------------
P0 (0x80) Bit Registers
------------------------------------------------*/
sbit P0_0 = 0x80;
sbit P0_1 = 0x81;
sbit P0_2 = 0x82;
sbit P0_3 = 0x83;
sbit P0_4 = 0x84;
sbit P0_5 = 0x85;
sbit P0_6 = 0x86;
sbit P0_7 = 0x87;
/*------------------------------------------------
PCON (0x87) Bit Values
------------------------------------------------*/
#define IDL_ 0x01 /* Idle Mode Bit: 1=Active */
#define PD_ 0x02 /* Alternate definition */
#define GF0_ 0x04 /* General Purpose Flag 0 */
#define GF1_ 0x08 /* General Purpose Flag 1 */
#define SMOD_ 0x80 /* Double Baud Rate Bit for use with Timer 1 */
/*------------------------------------------------
TCON (0x88) Bit Registers
------------------------------------------------*/
sbit IT0 = 0x88; /* Interrupt 0 Type Control Bit */
sbit IE0 = 0x89; /* Interrupt 0 Edge Flag */
sbit IT1 = 0x8A; /* Interrupt 1 Type Control Bit */
sbit IE1 = 0x8B; /* Interrupt 1 Edge Flag */
sbit TR0 = 0x8C; /* Timer 0 Run Control Bit */
sbit TF0 = 0x8D; /* Timer 0 Overflow Flag */
sbit TR1 = 0x8E; /* Timer 1 Run Control Bit */
sbit TF1 = 0x8F; /* Timer 1 Overflow Flag */
/*------------------------------------------------
TMOD (0x89) Bit Values
------------------------------------------------*/
#define T0_M0_ 0x01 /* Timer 0 Mode Bit 0 */
#define T0_M1_ 0x02 /* Timer 0 Mode Bit 1 */
#define T0_CT_ 0x04 /* Timer 0 Counter/Timer Select: 0=Counter, 1=Timer */
#define T0_GATE_ 0x08 /* Timer 0 Gate Control */
#define T1_M0_ 0x10 /* Timer 1 Mode Bit 0 */
#define T1_M1_ 0x20 /* Timer 1 Mode Bit 1 */
#define T1_CT_ 0x40 /* Timer 1 Counter/Timer Select: 0=Counter, 1=Timer */
#define T1_GATE_ 0x80 /* Timer 1 Gate Control */
#define T1_MASK_ 0xF0 /* Timer 0 Mask */
#define T0_MASK_ 0x0F /* Timer 1 Mask */
/*------------------------------------------------
P1 (0x90) Bit Registers
------------------------------------------------*/
sbit P1_0 = 0x90;
sbit P1_1 = 0x91;
sbit P1_2 = 0x92;
sbit P1_3 = 0x93;
sbit P1_4 = 0x94;
sbit P1_5 = 0x95;
sbit P1_6 = 0x96;
sbit P1_7 = 0x97;
sbit T2 = 0x90; /* External input to Timer/Counter 2, clock out */
sbit T2EX = 0x91; /* Timer/Counter 2 capture/reload trigger & dir ctl */
sbit MOSI = 0x95; /* SPI: MOSI - Master data output, slave data input */
sbit MISO = 0x96; /* SPI: MISO - Master data input, slave data output */
sbit SCK = 0x97; /* SPI: SCK - Master clock output, slave clock input */
/*------------------------------------------------
SCON (0x98) Bit Registers
------------------------------------------------*/
sbit RI = 0x98; /* Receive Interrupt Flag */
sbit TI = 0x99; /* Transmit Interrupt Flag */
sbit RB8 = 0x9A; /* 9th data bit received */
sbit TB8 = 0x9B; /* 9th data bit to be transmitted in modes 2 & 3 */
sbit REN = 0x9C; /* Receive Enable */
sbit SM2 = 0x9D; /* Serial Port Mode Bit 2 */
sbit SM1 = 0x9E; /* Serial Port Mode Bit 1 */
sbit SM0 = 0x9F; /* Serial Port Mode Bit 0 */
/*------------------------------------------------
P2 (0xA0) Bit Registers
------------------------------------------------*/
sbit P2_0 = 0xA0;
sbit P2_1 = 0xA1;
sbit P2_2 = 0xA2;
sbit P2_3 = 0xA3;
sbit P2_4 = 0xA4;
sbit P2_5 = 0xA5;
sbit P2_6 = 0xA6;
sbit P2_7 = 0xA7;
/*------------------------------------------------
IE (0xA8) Bit Registers
------------------------------------------------*/
sbit EX0 = 0xA8; /* External Interrupt 0 Enable: 1=Enabled */
sbit ET0 = 0xA9; /* Timer 0 Interrupt Enable: 1=Enabled */
sbit EX1 = 0xAA; /* External Interrupt 1 Enable: 1=Enabled */
sbit ET1 = 0xAB; /* Timer 1 Interrupt Enable: 1=Enabled */
sbit ES = 0xAC; /* SPI and UART Interrupt Enable: 1=Enabled */
sbit ET2 = 0xAD; /* Timer 2 Interrupt Enable: 1=Enabled */
sbit EA = 0xAF; /* Global Interrupt Enable: 0=Disable all interrupts */
/*------------------------------------------------
P3 (0xB0) Bit Registers (Mnemonics & Ports)
------------------------------------------------*/
sbit P3_0 = 0xB0;
sbit P3_1 = 0xB1;
sbit P3_2 = 0xB2;
sbit P3_3 = 0xB3;
sbit P3_4 = 0xB4;
sbit P3_5 = 0xB5;
sbit P3_6 = 0xB6;
sbit P3_7 = 0xB7;
sbit RXD = 0xB0; /* Serial data input */
sbit TXD = 0xB1; /* Serial data output */
sbit INT0 = 0xB2; /* External interrupt 0 */
sbit INT1 = 0xB3; /* External interrupt 1 */
sbit T0 = 0xB4; /* Timer 0 external input */
sbit T1 = 0xB5; /* Timer 1 external input */
sbit WR = 0xB6; /* External data memory write strobe */
sbit RD = 0xB7; /* External data memory read strobe */
/*------------------------------------------------
IP (0xB8) Bit Registers
------------------------------------------------*/
sbit PX0 = 0xB8; /* External Interrupt 0 Priority Bit */
sbit PT0 = 0xB9; /* Timer 0 Interrupt Priority Bit */
sbit PX1 = 0xBA; /* External Interrupt 1 Priority Bit */
sbit PT1 = 0xBB; /* Timer 1 Interrupt Priority Bit */
sbit PS = 0xBC; /* Serial Port Interrupt Priority Bit */
sbit PT2 = 0xBD; /* Timer 2 Interrupt Priority Bit */
/*------------------------------------------------
T2CON (0xC8) Bit Registers
------------------------------------------------*/
sbit CP_RL2= 0xC8; /* 0=Reload, 1=Capture select */
sbit C_T2 = 0xC9; /* 0=Timer, 1=Counter */
sbit TR2 = 0xCA; /* 0=Stop timer, 1=Start timer */
sbit EXEN2= 0xCB; /* Timer 2 external enable */
sbit TCLK = 0xCC; /* 0=Serial clock uses Timer 1 overflow, 1=Timer 2 */
sbit RCLK = 0xCD; /* 0=Serial clock uses Timer 1 overflow, 1=Timer 2 */
sbit EXF2 = 0xCE; /* Timer 2 external flag */
sbit TF2 = 0xCF; /* Timer 2 overflow flag */
/*------------------------------------------------
T2MOD (0xC9) Bit Values
------------------------------------------------*/
#define DCEN_ 0x01 /* 1=Timer 2 can be configured as up/down counter */
#define T2OE_ 0x02 /* Timer 2 output enable */
/*------------------------------------------------
PSW (0xD0) Bit Registers
------------------------------------------------*/
sbit P = 0xD0; /* Parity Flag */
sbit FL = 0xD1; /* User Flag */
sbit OV = 0xD2; /* Overflow Flag */
sbit RS0 = 0xD3; /* Register Bank Select Bit 0 */
sbit RS1 = 0xD4; /* Register Bank Select Bit 1 */
sbit F0 = 0xD5; /* User Flag 0 */
sbit AC = 0xD6; /* Auxiliary Carry Flag */
sbit CY = 0xD7; /* Carry Flag */
/*------------------------------------------------
Interrupt Vectors:
Interrupt Address = (Number * 8) + 3
------------------------------------------------*/
#define IE0_VECTOR 0 /* 0x03 External Interrupt 0 */
#define TF0_VECTOR 1 /* 0x0B Timer 0 */
#define IE1_VECTOR 2 /* 0x13 External Interrupt 1 */
#define TF1_VECTOR 3 /* 0x1B Timer 1 */
#define SIO_VECTOR 4 /* 0x23 Serial port */
#define TF2_VECTOR 5 /* 0x2B Timer 2 */
#define EX2_VECTOR 5 /* 0x2B External Interrupt 2 */
#endif
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -