/* Name: usbconfig.h * Project: AVR USB driver * Author: Christian Starkjohann * Creation Date: 2005-04-01 * Tabsize: 4 * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH * License: Proprietary, free under certain conditions. See Documentation. * This Revision: $Id: usbconfig.h 43 2005-04-10 21:04:36Z cs $ */#ifndef __usbconfig_h_included__#define	__usbconfig_h_included__/*General Description:This file contains parts of the USB driver which can be configured and can ormust be adapted to your hardware.*//* ---------------------------- Hardware Config ---------------------------- */#define	USB_CFG_IOPORT			PORTB/* This is the port where the USB bus is connected. When you configure it to * "PORTB", the registers PORTB, PINB (=PORTB+2) and DDRB (=PORTB+1) will be * used. */#define	USB_CFG_DMINUS_BIT		0/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. * This MUST be bit 0. All other values will result in a compile error! */#define	USB_CFG_DPLUS_BIT		1/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. * This may be any bit in the port. Please note that D+ must also be connected * to interrupt pin INT0! *//* --------------------------- Functional Range ---------------------------- */#define	USB_CFG_HAVE_INTRIN_ENDPOINT	0/* Define this to 1 if you want to compile a version with two endpoints: The * default control endpoint 0 and an interrupt-in endpoint 1. */#define	USB_CFG_INTR_POLL_INTERVAL		10/* If you compile a version with endpoint 1 (interrupt-in), this is the poll * interval. The value is in milliseconds and must not be less than 10 ms for * low speed devices. */#define	USB_CFG_IS_SELF_POWERED			0/* Define this to 1 if the device has its own power supply. Set it to 0 if the * device is powered from the USB bus. */#define	USB_CFG_MAX_BUS_POWER			50/* Set this variable to the maximum USB bus power consumption of your device. * The value is in milliamperes. [It will be divided by two since USB * communicates power requirements in units of 2 mA.] */#define	USB_CFG_SAMPLE_EXACT			1/* This variable affects Sampling Jitter for USB receiving. When it is 0, the * driver guarantees a sampling window of 1/2 bit. The USB spec requires * that the receiver has at most 1/4 bit sampling window. The 1/2 bit window * should still work reliably enough because we work at low speed. If you want * to meet the spec, set this value to 1. This will unroll a loop which * results in bigger code size. * If you have problems with long cables, try setting this value to 1. */#define USB_CFG_IMPLEMENT_FN_WRITE		1/* Set this to 1 if you want usbFunctionWrite() to be called for control-out * transfers. Set it to 0 if you don't need it and want to save a couple of * bytes. */#define USB_CFG_IMPLEMENT_FN_READ		1/* Set this to 1 if you need to send control replies which are generated * "on the fly" when usbFunctionRead() is called. If you only want to send * data from a static buffer, set it to 0 and return the data from * usbFunctionSetup(). This saves a couple of bytes. *//* -------------------------- Device Description --------------------------- */#define	USB_CFG_VENDOR_ID		0xeb, 0x03/* USB vendor ID for the device, low byte first. 0xeb, 0x03 is Atmel's vendor * ID. Don't use it for hardware you sell or publish! */#define	USB_CFG_DEVICE_ID		0xb4, 0xc7/* This is the ID of the device, low byte first. It is interpreted in the * scope of the vendor ID. The only requirement is that no two devices may * share the same product and vendor IDs. Not even if the devices are never * on the same bus together! */#define	USB_CFG_DEVICE_VERSION	0x00, 0x01/* Version number of the device: Minor number first, then major number. */#define	USB_CFG_VENDOR_NAME		'w', 'w', 'w', '.', 'f', 'i', 's', 'c', 'h', 'l', '.', 'd', 'e'#define	USB_CFG_VENDOR_NAME_LEN	13/* These two values define the vendor name returned by the USB device. The name * must be given as a list of characters under single quotes. The characters * are interpreted as Unicode (UTF-16) entities. * If you don't want a vendor name string, undefine these macros. */#define	USB_CFG_DEVICE_NAME		'U', 'S', 'B', 'a', 's', 'p'#define	USB_CFG_DEVICE_NAME_LEN	6/* Same as above for the device name. If you don't want a device name, undefine * the macros. */#define	USB_CFG_DEVICE_CLASS	0xff#define	USB_CFG_DEVICE_SUBCLASS	0/* See USB specification if you want to conform to an existing device class. */#define	USB_CFG_INTERFACE_CLASS		0#define	USB_CFG_INTERFACE_SUBCLASS	0#define	USB_CFG_INTERFACE_PROTOCOL	0/* See USB specification if you want to conform to an existing device class or * protocol. */#endif /* __usbconfig_h_included__ */