*                  - Data: specifies the data to be programmed.
* Output         : None
* Return         : FLASH Status: The returned value can be: FLASH_BUSY, 
*                  FLASH_ERROR_PG, FLASH_ERROR_WRP, FLASH_COMPLETE or 
*                  FLASH_TIMEOUT. 
*******************************************************************************/
FLASH_Status FLASH_ProgramWord(u32 Address, u32 Data)
{
  FLASH_Status status = FLASH_COMPLETE;

  /* Check the parameters */
  assert_param(IS_FLASH_ADDRESS(Address));

  /* Wait for last operation to be completed */
  status = FLASH_WaitForLastOperation(ProgramTimeout);
  
  if(status == FLASH_COMPLETE)
  {
    /* if the previous operation is completed, proceed to program the new first 
    half word */
    FLASH->CR |= CR_PG_Set;
  
    *(vu16*)Address = (u16)Data;

    /* Wait for last operation to be completed */
    status = FLASH_WaitForLastOperation(ProgramTimeout);
 
    if(status == FLASH_COMPLETE)
    {
      /* if the previous operation is completed, proceed to program the new second 
      half word */
      *(vu16*)(Address + 2) = Data >> 16;
    
      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(ProgramTimeout);
        
      if(status != FLASH_BUSY)
      {
        /* Disable the PG Bit */
        FLASH->CR &= CR_PG_Reset;
      }
    }
    else
    {
      if (status != FLASH_BUSY)
      {
        /* Disable the PG Bit */
        FLASH->CR &= CR_PG_Reset;
      }
     }
  }
  /* Return the Program Status */
  return status;
}

/*******************************************************************************
* Function Name  : FLASH_ProgramHalfWord
* Description    : Programs a half word at a specified address.
* Input          : - Address: specifies the address to be programmed.
*                  - Data: specifies the data to be programmed.
* Output         : None
* Return         : FLASH Status: The returned value can be: FLASH_BUSY, 
*                  FLASH_ERROR_PG, FLASH_ERROR_WRP, FLASH_COMPLETE or 
*                  FLASH_TIMEOUT. 
*******************************************************************************/
FLASH_Status FLASH_ProgramHalfWord(u32 Address, u16 Data)
{
  FLASH_Status status = FLASH_COMPLETE;

  /* Check the parameters */
  assert_param(IS_FLASH_ADDRESS(Address));

  /* Wait for last operation to be completed */
  status = FLASH_WaitForLastOperation(ProgramTimeout);
  
  if(status == FLASH_COMPLETE)
  {
    /* if the previous operation is completed, proceed to program the new data */
    FLASH->CR |= CR_PG_Set;
  
    *(vu16*)Address = Data;
    /* Wait for last operation to be completed */
    status = FLASH_WaitForLastOperation(ProgramTimeout);

    if(status != FLASH_BUSY)
    {
      /* if the program operation is completed, disable the PG Bit */
      FLASH->CR &= CR_PG_Reset;
    }
  } 
  /* Return the Program Status */
  return status;
}

/*******************************************************************************
* Function Name  : FLASH_ProgramOptionByteData
* Description    : Programs a half word at a specified Option Byte Data address.
* Input          : - Address: specifies the address to be programmed.
*                    This parameter can be 0x1FFFF804 or 0x1FFFF806. 
*                  - Data: specifies the data to be programmed.
* Output         : None
* Return         : FLASH Status: The returned value can be: FLASH_BUSY, 
*                  FLASH_ERROR_PG, FLASH_ERROR_WRP, FLASH_COMPLETE or 
*                  FLASH_TIMEOUT. 
*******************************************************************************/
FLASH_Status FLASH_ProgramOptionByteData(u32 Address, u8 Data)
{
  FLASH_Status status = FLASH_COMPLETE;

  /* Check the parameters */
  assert_param(IS_OB_DATA_ADDRESS(Address));

  status = FLASH_WaitForLastOperation(ProgramTimeout);

  if(status == FLASH_COMPLETE)
  {
    /* Authorize the small information block programming */
    FLASH->OPTKEYR = FLASH_KEY1;
    FLASH->OPTKEYR = FLASH_KEY2;

    /* Enables the Option Bytes Programming operation */
    FLASH->CR |= CR_OPTPG_Set; 
    *(vu16*)Address = Data;
    
    /* Wait for last operation to be completed */
    status = FLASH_WaitForLastOperation(ProgramTimeout);

    if(status != FLASH_BUSY)
    {
      /* if the program operation is completed, disable the OPTPG Bit */
      FLASH->CR &= CR_OPTPG_Reset;
    }
  }    
  /* Return the Option Byte Data Program Status */
  return status;      
}

/*******************************************************************************
* Function Name  : FLASH_EnableWriteProtection
* Description    : Write protects the desired pages
* Input          : - FLASH_Pages: specifies the address of the pages to be 
*                    write protected. This parameter can be:
*                    - For STM32F10Xxx Medium-density devices (FLASH page size equal to 1 KB)
*                       - A value between FLASH_WRProt_Pages0to3 and 
*                         FLASH_WRProt_Pages124to127
*                    - For STM32F10Xxx High-density devices (FLASH page size equal to 2 KB) 
*                       - A value between FLASH_WRProt_Pages0to1 and
*                         FLASH_WRProt_Pages60to61 or FLASH_WRProt_Pages62to255 
*                       - FLASH_WRProt_AllPages
* Output         : None
* Return         : FLASH Status: The returned value can be: FLASH_BUSY, 
*                  FLASH_ERROR_PG, FLASH_ERROR_WRP, FLASH_COMPLETE or 
*                  FLASH_TIMEOUT.
*******************************************************************************/
FLASH_Status FLASH_EnableWriteProtection(u32 FLASH_Pages)
{
  u16 WRP0_Data = 0xFFFF, WRP1_Data = 0xFFFF, WRP2_Data = 0xFFFF, WRP3_Data = 0xFFFF;
  
  FLASH_Status status = FLASH_COMPLETE;
  
  /* Check the parameters */
  assert_param(IS_FLASH_WRPROT_PAGE(FLASH_Pages));
  
  FLASH_Pages = (u32)(~FLASH_Pages);
  WRP0_Data = (vu16)(FLASH_Pages & WRP0_Mask);
  WRP1_Data = (vu16)((FLASH_Pages & WRP1_Mask) >> 8);
  WRP2_Data = (vu16)((FLASH_Pages & WRP2_Mask) >> 16);
  WRP3_Data = (vu16)((FLASH_Pages & WRP3_Mask) >> 24);
  
  /* Wait for last operation to be completed */
  status = FLASH_WaitForLastOperation(ProgramTimeout);
  
  if(status == FLASH_COMPLETE)
  {
    /* Authorizes the small information block programming */
    FLASH->OPTKEYR = FLASH_KEY1;
    FLASH->OPTKEYR = FLASH_KEY2;
    FLASH->CR |= CR_OPTPG_Set;

    if(WRP0_Data != 0xFF)
    {
      OB->WRP0 = WRP0_Data;
      
      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(ProgramTimeout);
    }
    if((status == FLASH_COMPLETE) && (WRP1_Data != 0xFF))
    {
      OB->WRP1 = WRP1_Data;
      
      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(ProgramTimeout);
    }

    if((status == FLASH_COMPLETE) && (WRP2_Data != 0xFF))
    {
      OB->WRP2 = WRP2_Data;
      
      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(ProgramTimeout);
    }
    
    if((status == FLASH_COMPLETE)&& (WRP3_Data != 0xFF))
    {
      OB->WRP3 = WRP3_Data;
     
      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(ProgramTimeout);
    }
          
    if(status != FLASH_BUSY)
    {
      /* if the program operation is completed, disable the OPTPG Bit */
      FLASH->CR &= CR_OPTPG_Reset;
    }
  } 
  /* Return the write protection operation Status */
  return status;       
}

/*******************************************************************************
* Function Name  : FLASH_ReadOutProtection
* Description    : Enables or disables the read out protection.
*                  If the user has already programmed the other option bytes before 
*                  calling this function, he must re-program them since this 
*                  function erases all option bytes.
* Input          : - Newstate: new state of the ReadOut Protection.
*                    This parameter can be: ENABLE or DISABLE.
* Output         : None
* Return         : FLASH Status: The returned value can be: FLASH_BUSY, 
*                  FLASH_ERROR_PG, FLASH_ERROR_WRP, FLASH_COMPLETE or 
*                  FLASH_TIMEOUT.
*******************************************************************************/
FLASH_Status FLASH_ReadOutProtection(FunctionalState NewState)
{
  FLASH_Status status = FLASH_COMPLETE;

  /* Check the parameters */
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  status = FLASH_WaitForLastOperation(EraseTimeout);

  if(status == FLASH_COMPLETE)
  {
    /* Authorizes the small information block programming */
    FLASH->OPTKEYR = FLASH_KEY1;
    FLASH->OPTKEYR = FLASH_KEY2;

    FLASH->CR |= CR_OPTER_Set;
    FLASH->CR |= CR_STRT_Set;

    /* Wait for last operation to be completed */
    status = FLASH_WaitForLastOperation(EraseTimeout);

    if(status == FLASH_COMPLETE)
    {
      /* if the erase operation is completed, disable the OPTER Bit */
      FLASH->CR &= CR_OPTER_Reset;

      /* Enable the Option Bytes Programming operation */
      FLASH->CR |= CR_OPTPG_Set; 

      if(NewState != DISABLE)
      {
        OB->RDP = 0x00;
      }
      else
      {
        OB->RDP = RDP_Key;  
      }

      /* Wait for last operation to be completed */
      status = FLASH_WaitForLastOperation(EraseTimeout); 
    
      if(status != FLASH_BUSY)
      {
        /* if the program operation is completed, disable the OPTPG Bit */
        FLASH->CR &= CR_OPTPG_Reset;
      }
    }
    else 
    {
      if(status != FLASH_BUSY)
      {
        /* Disable the OPTER Bit */
        FLASH->CR &= CR_OPTER_Reset;
      }
    }
  }
  /* Return the protection operation Status */
  return status;      
}
  	
/*******************************************************************************
* Function Name  : FLASH_UserOptionByteConfig
* Description    : Programs the FLASH User Option Byte: IWDG_SW / RST_STOP /
*                  RST_STDBY.
* Input          : - OB_IWDG: Selects the IWDG mode
*                     This parameter can be one of the following values:
*                     - OB_IWDG_SW: Software IWDG selected
*                     - OB_IWDG_HW: Hardware IWDG selected
*                  - OB_STOP: Reset event when entering STOP mode.
*                     This parameter can be one of the following values:
*                     - OB_STOP_NoRST: No reset generated when entering in STOP
*                     - OB_STOP_RST: Reset generated when entering in STOP