/*******************************************************************************************************
 *                                                                                                     *
 *        **********                                                                                   *
 *       ************                                                                                  *
 *      ***        ***                                                                                 *
 *      ***   +++   ***                                                                                *
 *      ***   + +   ***     This file register settings for the 5 different frequency band             *
 *      ***   +             supported by CCxx00.                                                       *
 *      ***   + +   ***                                                                                *
 *      ***   +++   ***     RegSettings_SerialLink.c                                                   *
 *      ***        ***                                                                                 *
 *       ************                                                                                  *
 *        **********                                                                                   *
 *                                                                                                     *
 *******************************************************************************************************
 * Compiler:                Keil C51 V7.50                                                             *
 * Target platform:         Chipcon CCxxx0 (Silabs F320)                                               *
 * Author:                  SNA                                                                        *
 *******************************************************************************************************
 * Revision history:     See end of file                                                               *
 *******************************************************************************************************/
#include <Chipcon\srf04\regssrf04.h>
#include <Chipcon\srf04\halsrf04.h>
#include <Chipcon\srf04\ebsrf04.h>




//-------------------------------------------------------------------------------------------------------
#ifdef FREQ_315_CC1100
// Chipcon
// Product = CC1100
// Chip version = F   (VERSION = 0x03)
// Crystal accuracy = 10 ppm
// X-tal frequency = 26 MHz
// RF output power = 0 dBm
// RX filterbandwidth = 325.000000 kHz
// Deviation = 48 kHz
// Datarate = 99.975586 kBaud
// Modulation = (0) 2-FSK
// Manchester enable = (0) Manchester disabled
// RF Frequency = 314.999664 MHz
// Channel spacing = 199.951172 kHz
// Channel number = 0
// Optimization = -
// Sync mode = (0) No preamble/sync
// Format of RX/TX data = (1) Serial Synchronous mode, used for backwards compatibility
// CRC operation = (0) CRC disabled for TX and RX
// Forward Error Correction = (0) FEC disabled
// Length configuration = (2) Enable infinite length packets.
// Packetlength = 255
// Preamble count = (2)  4 bytes
// Append status = 1
// Address check = (0) No address check
// FIFO autoflush = 0
// Device address = 0
// GDO0 signal selection = (12) Serial Synchronous Data Output
// GDO2 signal selection = (11) Serial Clock
RF_SETTINGS code rfSettings = {
    0x08,   // FSCTRL1   Frequency synthesizer control.
    0x00,   // FSCTRL0   Frequency synthesizer control.
    0x0C,   // FREQ2     Frequency control word, high byte.
    0x1D,   // FREQ1     Frequency control word, middle byte.
    0x89,   // FREQ0     Frequency control word, low byte.
    0x5B,   // MDMCFG4   Modem configuration.
    0xF8,   // MDMCFG3   Modem configuration.
    0x00,   // MDMCFG2   Modem configuration.
    0x22,   // MDMCFG1   Modem configuration.
    0xF8,   // MDMCFG0   Modem configuration.
    0x00,   // CHANNR    Channel number.
    0x47,   // DEVIATN   Modem deviation setting (when FSK modulation is enabled).
    0xB6,   // FREND1    Front end RX configuration.
    0x10,   // FREND0    Front end RX configuration.
    0x18,   // MCSM0     Main Radio Control State Machine configuration.
    0x1D,   // FOCCFG    Frequency Offset Compensation Configuration.
    0x1C,   // BSCFG     Bit synchronization Configuration.
    0xC7,   // AGCCTRL2  AGC control.
    0x00,   // AGCCTRL1  AGC control.
    0xB2,   // AGCCTRL0  AGC control.
    0xEA,   // FSCAL3    Frequency synthesizer calibration.
    0x2A,   // FSCAL2    Frequency synthesizer calibration.
    0x00,   // FSCAL1    Frequency synthesizer calibration.
    0x1F,   // FSCAL0    Frequency synthesizer calibration.
    0x59,   // FSTEST    Frequency synthesizer calibration.
    0x81,   // TEST2     Various test settings.
    0x35,   // TEST1     Various test settings.
    0x0B,   // TEST0     Various test settings.
    0x07,   // FIFOTHR   RXFIFO and TXFIFO thresholds.
    0x0B,   // IOCFG2    GDO2 output pin configuration.
    0x0C,   // IOCFG0D   GDO0 output pin configuration. Refer to SmartRF