//////////////遠程幀控制發送程序///////////////
////////////remote_can_t.c/////////////////////
#include "candeal2.h"
#define LEN 8
#define MSGNUMA 2
#define MSGNUMB 5
#define NUMAPEND 0x0002
#define NUMBPEND 0x0010
xdata uchar rr1[LEN];
xdata uchar rr2[LEN];
xdata uchar ss1[LEN]={0x91,0x92,0x93,0x94,0x95,0x96,0x97,0x98};
xdata uchar ss2[LEN]={0xa1,0xa2,0xa3,0xa4,0xa5,0xa6,0xa7,0xa8};
bit isupB;
xdata uchar countA;
void canini(){
	clear_msg_objects();
	remote_rqst_ini(MSGNUMA,4);
	remote_send_ini(MSGNUMB,2);
	EIE2 |= 0x20;
	EA = 1;
	SFRPAGE = CAN0_PAGE;
	CAN0CN=0X41;
	CAN0ADR=BITREG;
	CAN0DAT=0X34c0;//調波特率
	start_CAN();
}
void config(){
//看門狗禁止
	WDTCN = 0x07;	
    WDTCN = 0xDE;   
   	WDTCN = 0xAD;
	SFRPAGE = 0x0F;
//交叉開關使能，但沒有進行外圍設備配置
	XBR0 = 0x00;	
	XBR1 = 0x00;	
	XBR2 = 0x40;
 	XBR3 = 0x00;   
//管腳輸出配置，P0口為開漏輸出，其中P0.6接上拉電阻，P0為數字輸入口
 	SFRPAGE = 0x0F;
 	P0MDOUT = 0x00; 
 	P1MDIN = 0xFF;  
//晶振配置，采用內部晶振8分頻
	SFRPAGE = 0x0F;
 	CLKSEL = 0x00;  
	OSCXCN = 0x00;	
	OSCICN = 0x84;	
}
main(){
	uchar i;
	config();
	for(i=0;i<LEN;i++){
		rr1[i]=0;
		rr2[i]=0;
	}
	canini();
	remote_send_updata(MSGNUMB,ss1,LEN);
	isupB=0;
	countA=0;
	remote_rqst(MSGNUMA);
	while(1);
	
}
void CAN_ISR(void) interrupt 19

{	uint temp;
	temppage=SFRPAGE;
    SFRPAGE = CAN0_PAGE;
    status = CAN0STA;
    if((status&0x10) != 0){
   		CAN0STA&=0xef;
		CAN0ADR=INTPEND1;
		temp=CAN0DAT;
		if((temp&NUMAPEND)!=0){
			if(countA==0){
				receive_data (MSGNUMA,rr1,LEN);
				remote_rqst(MSGNUMA);
			}
			if(countA==1)//總共發送兩次遠程幀請求
				receive_data (MSGNUMA,rr2,LEN);
			countA++;
		}
	}
	if ((status&0x08)!=0){
	   	CAN0STA&=0xf7;
		CAN0ADR=INTPEND1;
		temp=CAN0DAT;
		if((temp&NUMBPEND)!=0){
			remote_send_updata(MSGNUMB,ss2,LEN);
			isupB=1;//主程序中可通過查詢ispuB值檢查數據是否更新
		}
   } 
   SFRPAGE=temppage;
}