#include<AT89X51.h>

/*

char *xdata a; 
char xdata *a;
char data *xdata a;
上面3個指針，我概念比較混亂，看了書后也不是特別明白。還請高手幫忙給通俗地解釋解釋。謝謝！

xdata: 存儲在外部RAM 
data：存儲在內部RAM
要存儲的內容：
1.指針char *a指向的Byte串，2.指針本身,一般要3Byte
如果沒有指定存儲的地方（哪種RAM）,按編譯模式設定，一般是存儲在data (small模式）。這樣
char *xdata a
char data *xdata a
是相同的，都是表示指針本身存儲在外部RAM，指針指向的數據存儲在內部RAM
char xdata *a指指針本身3Byte存儲在內部RAM，指針指向的Byte串存儲在外部RAM XDATA。
一般盡量用內部RAM，data 數組的數據大，內部RAM放不下，用外部RAM保持數組內容
char xdata *a
這時指針本身的3Byte還是在內部RAM中；內部RAM不夠用，可以把這3Byte也放倒外部RAM
char xdata *xdata a	

*/


#define CH371_PAGE 0
#define CH371_SYSTEM (unsigned char xdata *)2
#define CH371_CONFIG (unsigned char xdata *)2
#define CH371_INT_SET (unsigned char xdata*)6
#define CH371_STATUS (unsigned char xdata*)6
#define CH371_LENGTH (unsigned char xdata*)7
#define CH371_BUFFER (unsigned char xdata*)8

unsigned char save_status;
unsigned char save_length;
unsigned char save_buffer[8]={0};
unsigned char *temp;
unsigned char counter;
bit ReceiveFlag;
void Init(void)
{
	*CH371_LENGTH=15;
	save_length=0;
	IT0=1;		
	IE0=0;
	PX0=1;
	EX0=1; 
	EA=1;	 

}

void UpLoad(unsigned char *pBuffer,unsigned len)
{
	   temp=CH371_BUFFER;
	for(counter=0;counter<len;counter++)
	{
		*temp++=*pBuffer++;

	}

	*CH371_LENGTH=len;

}

void ExtInt0() interrupt 0
{
	   save_status=*CH371_STATUS;
	   if(save_status&0x01)
	   {
	   	 *CH371_LENGTH=15;
	   }
	   else{
	   		
			P1=0xff;
		 temp=CH371_BUFFER;
	   	 save_length=*CH371_LENGTH;
		 for(counter=0;counter<save_length;counter++)
		  {save_buffer[counter]=*temp++;
		   ReceiveFlag=1;
		  }
		  	   
	   }

}
 
 void main(){			 
 
 	  temp=0;
	  counter=0;
	  ReceiveFlag=0;
	  P1=0;
	  Init();

	  while(1)
	  {
	  	if(ReceiveFlag==1)
	  	{
	  		if(save_buffer[0]==0x90)
			{
			   save_buffer[0]=~save_buffer[0];
			   save_buffer[1]=~save_buffer[1];
			   save_buffer[2]=~save_buffer[2];
			   UpLoad(save_buffer,8);

			}
			ReceiveFlag=0;
	  
	  	}
 
	  }
 }