?? xst.xmsgs
字號(hào):
<?xml version="1.0" encoding="UTF-8"?>
<!-- IMPORTANT: This is an internal file that has been generated
by the Xilinx ISE software. Any direct editing or
changes made to this file may result in unpredictable
behavior or data corruption. It is strongly advised that
users do not edit the contents of this file. -->
<messages>
<msg type="warning" file="HDLCompilers" num="259" delta="old" ><arg fmt="%s" index="1">"MKeyExtend.v" line 48 </arg>Connection to input port '<arg fmt="%s" index="2">AddrCK_in</arg>' does not match port size
</msg>
<msg type="warning" file="Xst" num="905" delta="old" >"<arg fmt="%s" index="1">MEncryptDecrypt_SMS4_try.v</arg>" line <arg fmt="%d" index="2">99</arg>: The signals <<arg fmt="%s" index="3">SubKey1</arg>> are missing in the sensitivity list of always block.
</msg>
<msg type="warning" file="Xst" num="905" delta="old" >"<arg fmt="%s" index="1">MEncryptDecrypt_SMS4_try.v</arg>" line <arg fmt="%d" index="2">152</arg>: The signals <<arg fmt="%s" index="3">SubKeyMemory</arg>> are missing in the sensitivity list of always block.
</msg>
<msg type="warning" file="Xst" num="905" delta="old" >"<arg fmt="%s" index="1">MEncryptDecrypt_SMS4_try.v</arg>" line <arg fmt="%d" index="2">157</arg>: The signals <<arg fmt="%s" index="3">Start_in, Count, OutData</arg>> are missing in the sensitivity list of always block.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL10</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL13</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL18</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL23</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL24</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">BL2</arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="0" delta="new" >Property "<arg fmt="%s" index="1">use_dsp48</arg>" is not applicable for this technology.
</msg>
<msg type="warning" file="Xst" num="646" delta="old" >Signal <<arg fmt="%s" index="1">OutData<127:32></arg>> is assigned but never used.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">5</arg>-bit latch for signal <<arg fmt="%s" index="2">Addr</arg>>.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">32</arg>-bit latch for signal <<arg fmt="%s" index="2">SubKeyMemory_3</arg>>.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">32</arg>-bit latch for signal <<arg fmt="%s" index="2">SubKeyMemory_2</arg>>.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">32</arg>-bit latch for signal <<arg fmt="%s" index="2">SubKeyMemory_1</arg>>.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">32</arg>-bit latch for signal <<arg fmt="%s" index="2">SubKeyMemory_0</arg>>.
</msg>
<msg type="warning" file="Xst" num="737" delta="old" >Found <arg fmt="%d" index="1">8</arg>-bit latch for signal <<arg fmt="%s" index="2">ShowDigit_out</arg>>.
</msg>
<msg type="info" file="Xst" num="2371" delta="old" >HDL ADVISOR - Logic functions respectively driving the data and gate enable inputs of this latch share common terms. This situation will potentially lead to setup/hold violations and, as a result, to simulation problems. This situation may come from an incomplete case statement (all selector values are not covered). You should carefully review if it was in your intentions to describe such a latch.
</msg>
<msg type="info" file="Xst" num="2169" delta="old" >HDL ADVISOR - Some clock signals were not automatically buffered by XST with BUFG/BUFR resources. Please use the buffer_type constraint in order to insert these buffers to the clock signals to help prevent skew problems.
</msg>
</messages>
?? 快捷鍵說明
復(fù)制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號(hào)
Ctrl + =
減小字號(hào)
Ctrl + -