*                  - USART_IT: specifies the USART interrupt sources to be
*                    enabled or disabled.
*                    This parameter can be one of the following values:
*                       - USART_IT_CTS:  CTS change interrupt (not available for
*                                        UART4 and UART5)
*                       - USART_IT_LBD:  LIN Break detection interrupt
*                       - USART_IT_TXE:  Tansmit Data Register empty interrupt
*                       - USART_IT_TC:   Transmission complete interrupt
*                       - USART_IT_RXNE: Receive Data register not empty 
*                                        interrupt
*                       - USART_IT_IDLE: Idle line detection interrupt
*                       - USART_IT_PE:   Parity Error interrupt
*                       - USART_IT_ERR:  Error interrupt(Frame error, noise
*                                        error, overrun error)
*                  - NewState: new state of the specified USARTx interrupts.
*                    This parameter can be: ENABLE or DISABLE.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_ITConfig(USART_TypeDef* USARTx, u16 USART_IT, FunctionalState NewState)
{
  u32 usartreg = 0x00, itpos = 0x00, itmask = 0x00;
  u32 usartxbase = 0x00;

  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_USART_CONFIG_IT(USART_IT));
  assert_param(IS_USART_PERIPH_IT(USARTx, USART_IT)); /* The CTS interrupt is not available for UART4 and UART5 */     
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  usartxbase = (*(u32*)&(USARTx));

  /* Get the USART register index */
  usartreg = (((u8)USART_IT) >> 0x05);

  /* Get the interrupt position */
  itpos = USART_IT & IT_Mask;

  itmask = (((u32)0x01) << itpos);
    
  if (usartreg == 0x01) /* The IT is in CR1 register */
  {
    usartxbase += 0x0C;
  }
  else if (usartreg == 0x02) /* The IT is in CR2 register */
  {
    usartxbase += 0x10;
  }
  else /* The IT is in CR3 register */
  {
    usartxbase += 0x14; 
  }
  if (NewState != DISABLE)
  {
    *(vu32*)usartxbase  |= itmask;
  }
  else
  {
    *(vu32*)usartxbase &= ~itmask;
  }
}

/*******************************************************************************
* Function Name  : USART_DMACmd
* Description    : Enables or disables the USART抯 DMA interface.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3 or UART4.
*                    Note: The DMA mode is not available for UART5.
*                  - USART_DMAReq: specifies the DMA request.
*                    This parameter can be any combination of the following values:
*                       - USART_DMAReq_Tx: USART DMA transmit request
*                       - USART_DMAReq_Rx: USART DMA receive request
*                  - NewState: new state of the DMA Request sources.
*                   This parameter can be: ENABLE or DISABLE.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_DMACmd(USART_TypeDef* USARTx, u16 USART_DMAReq, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_USART_1234_PERIPH(USARTx));
  assert_param(IS_USART_DMAREQ(USART_DMAReq));  
  assert_param(IS_FUNCTIONAL_STATE(NewState)); 

  if (NewState != DISABLE)
  {
    /* Enable the DMA transfer for selected requests by setting the DMAT and/or
       DMAR bits in the USART CR3 register */
    USARTx->CR3 |= USART_DMAReq;
  }
  else
  {
    /* Disable the DMA transfer for selected requests by clearing the DMAT and/or
       DMAR bits in the USART CR3 register */
    USARTx->CR3 &= (u16)~USART_DMAReq;
  }
}

/*******************************************************************************
* Function Name  : USART_SetAddress
* Description    : Sets the address of the USART node.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - USART_Address: Indicates the address of the USART node.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_SetAddress(USART_TypeDef* USARTx, u8 USART_Address)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_USART_ADDRESS(USART_Address)); 
    
  /* Clear the USART address */
  USARTx->CR2 &= CR2_Address_Mask;
  /* Set the USART address node */
  USARTx->CR2 |= USART_Address;
}

/*******************************************************************************
* Function Name  : USART_WakeUpConfig
* Description    : Selects the USART WakeUp method.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - USART_WakeUp: specifies the USART wakeup method.
*                    This parameter can be one of the following values:
*                        - USART_WakeUp_IdleLine: WakeUp by an idle line detection
*                        - USART_WakeUp_AddressMark: WakeUp by an address mark
* Output         : None
* Return         : None
*******************************************************************************/
void USART_WakeUpConfig(USART_TypeDef* USARTx, u16 USART_WakeUp)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_USART_WAKEUP(USART_WakeUp));
  
  USARTx->CR1 &= CR1_WAKE_Mask;
  USARTx->CR1 |= USART_WakeUp;
}

/*******************************************************************************
* Function Name  : USART_ReceiverWakeUpCmd
* Description    : Determines if the USART is in mute mode or not.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - NewState: new state of the USART mute mode.
*                    This parameter can be: ENABLE or DISABLE.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_ReceiverWakeUpCmd(USART_TypeDef* USARTx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_FUNCTIONAL_STATE(NewState)); 
  
  if (NewState != DISABLE)
  {
    /* Enable the USART mute mode  by setting the RWU bit in the CR1 register */
    USARTx->CR1 |= CR1_RWU_Set;
  }
  else
  {
    /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */
    USARTx->CR1 &= CR1_RWU_Reset;
  }
}

/*******************************************************************************
* Function Name  : USART_LINBreakDetectLengthConfig
* Description    : Sets the USART LIN Break detection length.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - USART_LINBreakDetectLength: specifies the LIN break
*                    detection length.
*                    This parameter can be one of the following values:
*                       - USART_LINBreakDetectLength_10b: 10-bit break detection
*                       - USART_LINBreakDetectLength_11b: 11-bit break detection
* Output         : None
* Return         : None
*******************************************************************************/
void USART_LINBreakDetectLengthConfig(USART_TypeDef* USARTx, u16 USART_LINBreakDetectLength)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_USART_LIN_BREAK_DETECT_LENGTH(USART_LINBreakDetectLength));
  
  USARTx->CR2 &= CR2_LBDL_Mask;
  USARTx->CR2 |= USART_LINBreakDetectLength;  
}

/*******************************************************************************
* Function Name  : USART_LINCmd
* Description    : Enables or disables the USART抯 LIN mode.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - NewState: new state of the USART LIN mode.
*                    This parameter can be: ENABLE or DISABLE.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_LINCmd(USART_TypeDef* USARTx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  
  if (NewState != DISABLE)
  {
    /* Enable the LIN mode by setting the LINEN bit in the CR2 register */
    USARTx->CR2 |= CR2_LINEN_Set;
  }
  else
  {
    /* Disable the LIN mode by clearing the LINEN bit in the CR2 register */
    USARTx->CR2 &= CR2_LINEN_Reset;
  }
}

/*******************************************************************************
* Function Name  : USART_SendData
* Description    : Transmits single data through the USARTx peripheral.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  - Data: the data to transmit.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_SendData(USART_TypeDef* USARTx, u16 Data)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  assert_param(IS_USART_DATA(Data)); 
    
  /* Transmit Data */
  USARTx->DR = (Data & (u16)0x01FF);
}

/*******************************************************************************
* Function Name  : USART_ReceiveData
* Description    : Returns the most recent received data by the USARTx peripheral.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
* Output         : None
* Return         : The received data.
*******************************************************************************/
u16 USART_ReceiveData(USART_TypeDef* USARTx)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  
  /* Receive Data */
  return (u16)(USARTx->DR & (u16)0x01FF);
}

/*******************************************************************************
* Function Name  : USART_SendBreak
* Description    : Transmits break characters.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_SendBreak(USART_TypeDef* USARTx)
{
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  
  /* Send break characters */
  USARTx->CR1 |= CR1_SBK_Set;
}

/*******************************************************************************
* Function Name  : USART_SetGuardTime
* Description    : Sets the specified USART guard time.
* Input          : - USARTx: where x can be 1, 2 or 3 to select the USART
*                    peripheral.
*                  Note: The guard time bits are not available for UART4 and UART5.
*                  - USART_GuardTime: specifies the guard time.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_SetGuardTime(USART_TypeDef* USARTx, u8 USART_GuardTime)
{    
  /* Check the parameters */
  assert_param(IS_USART_123_PERIPH(USARTx));
  
  /* Clear the USART Guard time */
  USARTx->GTPR &= GTPR_LSB_Mask;
  /* Set the USART guard time */
  USARTx->GTPR |= (u16)((u16)USART_GuardTime << 0x08);
}

/*******************************************************************************
* Function Name  : USART_SetPrescaler
* Description    : Sets the system clock prescaler.
* Input          : - USARTx: Select the USART or the UART peripheral. 
*                    This parameter can be one of the following values:
*                     - USART1, USART2, USART3, UART4 or UART5.
*                  Note: The function is used for IrDA mode with UART4 and UART5.
*                  - USART_Prescaler: specifies the prescaler clock.
* Output         : None
* Return         : None
*******************************************************************************/
void USART_SetPrescaler(USART_TypeDef* USARTx, u8 USART_Prescaler)
{ 
  /* Check the parameters */
  assert_param(IS_USART_ALL_PERIPH(USARTx));
  
  /* Clear the USART prescaler */
  USARTx->GTPR &= GTPR_MSB_Mask;
  /* Set the USART prescaler */
  USARTx->GTPR |= USART_Prescaler;
}

/*******************************************************************************
* Function Name  : USART_SmartCardCmd
* Description    : Enables or disables the USART抯 Smart Card mode.
* Input          : - USARTx: where x can be 1, 2 or 3 to select the USART
*                    peripheral. 
*                    Note: The Smart Card mode is not available for UART4 and UART5.
*                  - NewState: new state of the Smart Card mode.
*                    This parameter can be: ENABLE or DISABLE.
* Output         : None