為深入了解基于UC3854A控制的PFC變換器中的動力學特性，研究系統參數變化對變換器中分岔現象的影響，在建立Boost PFC變換器雙閉環數學模型的基礎上，用Matlab軟件對變換器中慢時標分岔及混沌等不穩定現象進行了仿真。在對PFC變換器中慢時標分岔現象仿真的基礎上，分析了系統參數變化對分岔點的影響，并進行了仿真驗證。仿真結果清晰地顯示了輸入整流電壓的幅值變化對系統分岔點的影響。
Abstract:
In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
針對材料試驗機等設備中要求測量或控制材料拉伸或壓縮的位移，一般采用光電軸角編碼器檢測位置信號，輸出正交編碼脈沖信號。若采用其他方法檢測位置信號，必然導致電路設計復雜，可靠性降低。因此，提出一種基于LS7266R1的電子式萬能材料試驗機設計方案。給出了試驗機中的控制器工作原理，LS7266R1與單片機的接口硬件設計，以及主程序軟件流程圖。巧妙地把力量傳感器，位移傳感器等機械運動狀態的壓力或拉力以及位置坐標，變成了電壓信號和電脈沖數字信號，供A/D測量和LS7266R1計數，從而實現了獨立完成材料試驗控制或通過PC機串口命令完成材料試驗控制。
Abstract:
Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
為解決傳統可視倒車雷達視頻字符疊加器結構復雜，可靠性差，成本高昂等問題，在可視倒車雷達設計中采用視頻字符發生器芯片MAX7456。該芯片集成了所有用于產生用戶定義OSD，并將其插入視頻信號中所需的全部功能，僅需少量的外圍阻容元件即可正常工作。給出了以MAX7456為核心的可視倒車雷達的軟、硬件實現方案及設計實例。該方案具有電路結構簡單、價格低廉、符合人體視覺習慣的特點。經實際裝車測試，按該方案設計的可視倒車雷達視場清晰、提示字符醒目、工作可靠，可有效降低駕駛員倒車時的工作強度、減少倒車事故的發生。
Abstract:
A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
介紹了用單片機C 語言實現無功補償中電容組循環投切的基本原理和算法，并舉例說明。關鍵詞：循環投切;C51;無功補償中圖分類號： TM76 文獻標識碼： BAbstract: This paper introduces the aplication of C51 in the controlling of capacitorsuits cycle powered to be on and off in reactive compensation.it illustrate thefondamental principle and algorithm with example.Key words: cycle powered to be on and off; C51; reactive compensation
為提高功率因數，往往采用補償電容的方法來實現。而電容器的容量是由實時功率因數與標準值進行比較來決定的，實時功率因數小于標準值時，需投入電容組，實時功率因數大于標準值時，則需切除電容組。投切方式的不合理，會對電容器造成損壞，現有的控制器多采用“順序投切”方式，在這種投切方式下排序在前的電容器組，先投后切；而后面的卻后投先切。這不僅使處于前面的電容組經常處于運行狀態，積累熱量不易散失，影響其使用壽命，而且使后面的投切開關經常動作，同樣減少壽命。合理的投切方式應為“循環投切”。這種投切方式使先投入的運行的電容組先退出，后投的后切除，從而使各組電容及投切開關使用機率均等，降低了電容組的平均運行溫度，減少了投切開關的動作次數，延長了其使用壽命。
