Abstract: This article explores criteria necessary for reliable communication Between electric vehicles (EVs) and electric vehicleservice equipment (EVSE). Data will demonstrate that a G3-PLC system has already met the criteria established by the automotiveand utility industries. Multiple international tests prove that a G3-PLC implementation is the optimal low-frequency solution.
上傳時間： 2014-12-24
上傳用戶：逗逗666
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center Between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上傳時間： 2013-10-23
上傳用戶：wushengwu
Designers spend much time combating thermal effects incircuitry. The close relationship Between temperature andelectronic devices is the source of more design headachesthan any other consideration.
上傳時間： 2013-10-17
上傳用戶：風之驕子
Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection Between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上傳時間： 2013-10-25
上傳用戶：brain kung
This collection of circuits was worked out Between June1991 and July of 1994. Most were designed at customerrequest or are derivatives of such efforts. All representsubstantial effort and, as such, are disseminated here forwider study and (hopefully) use.1 The examples areroughly arranged in categories including power conversion,transducer signal conditioning, amplifiers and signalgenerators. As always, reader comment and questionsconcerning variants of the circuits shown may be addresseddirectly to the author.
上傳時間： 2013-11-15
上傳用戶：凌云御清風
Analog Inputs and Outputs in an S7 PLC are represented in the PLC as a 16-bit integer. Over the nominal span of the analog input or output, the value of this integer will range Between - 27648 and +27648. However, it is easier to use the analog values if they are scaled to the same units and ranges as the process being controlled. This applications tip describes methods for scaling analog values to and from engineering units.
上傳時間： 2013-11-17
上傳用戶：3294322651
為解決當前計算機串行通訊接口只有USB，難以滿足舊型號設備或某些單片機要求RS232通訊的問題，設計出兩款RS232/USB電路。采用CH341A與MAX223集成電路芯片構建標準9線RS232/USB通用接口轉換器，無需編程。采用CH341A與PIC16F877A構建單片機與計算機之間的USB通訊電路，軟件遵循RS232通訊協議，硬件進行電平轉換。實際使用表明，這兩款產品與計算機端Windows 操作系統下的串口應用程序完全兼容，且通訊過程中無握手失敗現象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit Between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上傳時間： 2013-11-03
上傳用戶：siying
以太網和CAN總線應用廣泛，但由于其通信協議不同，兩種總線器件間無法進行數據通信，因此，設計了基于CP2200與C8051F040的以太網總線與CAN總線接口轉換電路，并給出部分相關硬件電路與軟件設計分析。在保證數據完整和協議可靠的前提下，通過握手協議和簡化的以太網協議，不僅實現了以太網數據與CAN數據的轉發，同時還順利的解決了以太網的高速性與CAN的低速率沖突，以及兩者數據包之間的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating Between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching Between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上傳時間： 2013-10-15
上傳用戶：Ants
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸的接口電路原理圖。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication Between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上傳時間： 2013-12-19
上傳用戶：tecman
MG3500SoC是支持H.264高清編解碼器的片上系統，內部集成一個嵌入式ARM926處理器，支持高清H.264編解碼、MPEG鄄2解碼和JPEG編解碼。介紹了MG3500SoC的主要性能特點、引腳排列、主要接口功能及在DVR上的應用，以及MG3500SoC及其周圍器件的硬件設計，提出了在設計中應注意的問題。 Abstract: The MG3500System-on-Chip（SoC）is high definition（HD）H.264codec,including ARM926-EJ processor，H.264encoder/decoder，MPEG2decoder and JPEG/MJPEG encoder/decoder.The features,pin assignments，interfaces and the typical application of MG3500in DVR are introduced in this paper.The application hardware circuit Between the MG3500SoC and peripheral device are given,the questions which the syetem design needs to pay attention are explained.
上傳時間： 2013-11-12
上傳用戶：elinuxzj
