為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
標簽： 單總線 無線溫度 采集 系統設計
上傳時間： 2013-10-29
上傳用戶：515414293
氣壓是氣象監測中的一個重要參數，提出了一種氣壓數據采集模塊設計方案，該模塊采用數字氣壓傳感器MS5534B、MSP430單片機MSP430F2272和帶實時時鐘（RTC）64 KB鐵電存儲器。通過低功耗軟件設計方法以微安級整體平均功耗實現了氣壓數據的采集和存儲，適合電池供電的連續高精度氣壓采集應用。給出了模塊的軟硬件設計以及MS5534B的性能指標和使用經驗。 Abstract: Air pressure is an important parameter in weather monitor.This paper futs forward a new design scheme of low power-air pressure data acquisition module.The module uses a digital output barometer sensor MS5534B,MSP430 microcontroller MSP430F2272 and integrated RTC 64KB FRAM,precision air pressure measurement and storage chip.Another point of this module is low power consumption, so it is well suited for battery powered air pressure data acquisition applications. At the same time,the software and hardware deign of module is presented,And the speciaties and use notices of MS5534B are given.
上傳時間： 2014-12-27
上傳用戶：drink！
為深入了解基于UC3854A控制的PFC變換器中的動力學特性，研究系統參數變化對變換器中分岔現象的影響，在建立Boost PFC變換器雙閉環數學模型的基礎上，用Matlab軟件對變換器中慢時標分岔及混沌等不穩定現象進行了仿真。在對PFC變換器中慢時標分岔現象仿真的基礎上，分析了系統參數變化對分岔點的影響，并進行了仿真驗證。仿真結果清晰地顯示了輸入整流電壓的幅值變化對系統分岔點的影響。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上傳時間： 2013-10-17
上傳用戶：杜瑩12345
MPLAB C30用戶指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上傳時間： 2013-10-21
上傳用戶：13925096126
CAT5110/18/19/23/24/25 linear-taper digitally programmable potentiometers perform the same function as a mechanical potentiometer or a variable resistor. These devices consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a2-wire up/down serial interface.
上傳時間： 2013-11-22
上傳用戶：541657925
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
標簽： Pulsoximeter Single-Chip Des
上傳時間： 2013-10-27
上傳用戶：黑漆漆
The XL6003 regulator is fixed frequency PWM Boost (step-up) DC/DC converter, capable ofdriving 1050mA load current with excellent line and load regulation. The regulator is simple to use because it includes internal frequency compensation and a fixed-frequency oscillator so that it requires a minimum number of external components to work. The XL6003 could directly drive 5~10 3W LED units at VIN=12V.
上傳時間： 2013-11-07
上傳用戶：xy@1314
<Almost since the introduction of microcontrollers as electronic components there always has been an oscillatorcircuit on the device to make it work. From application point of view only some external components wererequired to make it work. However, to make sure that it will always work required more effort. This report is basedon feedback from the market from customers applying 8-bit mircrocontrollers.>
標簽： oscillators X-tal bit mic
上傳時間： 2013-11-12
上傳用戶：穿著衣服的大衛
基于單DSP的VoIP模擬電話適配器研究與實現:提出和實現了一種新穎的基于單個通用數字信號處理器(DSP)的VoIP模擬電話適配器方案。DSP的I/O和存儲資源非常有限，通常適于運算密集型應用，不適宜控制密集型應用[5]。該系統高效利用單DSP的I/O和片內外存儲器資源，采用μC/OS-II嵌入式實時操作系統，支持SIP和TCP-UDP/IP協議，通過LAN或者寬帶接入，使普通電話機成為Internet終端，實現IP電話。該系統軟硬件結構緊湊高效，運行穩定，成本低，具有廣闊的應用前景。關鍵詞：模擬電話適配器；IP電話；數字信號處理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitFixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上傳時間： 2013-11-20
上傳用戶：Wwill
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
標簽： LabVIEW 單片機 空調 溫度場
上傳時間： 2014-05-05
上傳用戶：KSLYZ
蟲蟲下載站版權所有 京ICP備2021023401號-1
