Abstract: Some types of loads require more current during startup than when running. Other loads can be limited to a lower-powercurrent during startup but require a Higher operating current. This article describes an application circuit that automatically adjusts apower circuit’s overcurrent protection level up or down after startup is complete.
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for Higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for Higher effi ciency.
Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their Higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
While simplicity and high effi ciency (for cool running) areno longer optional features in isolated power supplies, itis traditionally diffi cult to achieve both. Achieving higheffi ciency often requires the use of advanced topologiesand home-brewed secondary synchronous rectifi cationschemes once reserved only for Higher power applications.This only adds to the parts count and to the designcomplexity associated with the reference and optocouplercircuits typically used to maintain isolation. Fortunately, abreakthrough IC makes it possible to achieve both high efficiency and simplicity in a synchronous fl yback topology.The LT®3825 simplifi es and improves the performance oflow voltage, high current fl yback supplies by providingprecise synchronous rectifi er timing and eliminating theneed for optocoupler feedback while maintaining excellentregulation and superior loop response.
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, Higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
現有基于MAX7219芯片的數碼管驅動電路只適用于小尺寸LED，為擴展其使用范圍，在介紹動態顯示芯片MAX7219功能的基礎上，提出了一個基于該芯片的8位高亮度8英寸數碼管驅動電路。電路保留了MAX7219芯片的功能強大、編程簡單等優點，通過74LS273鎖存器和ULN2803達林頓驅動器，實現了對任意大尺寸數碼管提供較高電壓和電流驅動的靜態顯示，并亮度可調。
Abstract:
The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with Higher voltage and current was achieved with the help of 74LS273 and ULN2803.
生活中許多目標的高度和水平距離需要進行測量。目前主要的測量方法，仍以傳統的皮尺丈量為主，測量效率不高，有時還很不方便，沒有技術成熟的數字式測高測距產品。以基本的數學方法為理論依據，利用遙控小車做為載體，采用角度傳感器測量角度、霍爾傳感器測量水平距離等，通過單片機LM3S615進行數據計算，實現了對待測目標物體的高度、水平距離等數據的快速、精確和數字式的測量，高度測量精度可達99.06%，水平測量精度則可達98.06%。
Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is Higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
實時時鐘是微機保護裝置的重要部件，在討論PCF8583結構與功能的基礎上，提出采用dsPIC33F系列微處理器與串行I2C時鐘PCF8583的接口設計方案，給出了相應的接口電路與軟件流程。該設計方案結構簡單，可靠性高，開發周期短，具有一定的實用與參考價值。所設計的微機保護裝置已投入現場運行，效果良好。
Abstract:
Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，Higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel
Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to
enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements
include Higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power switches, sensors,
push buttons, LEDs, fans, etc.
The LPC1769/68/67/66/65/64 are ARM Cortex-M3 based microcontrollers for embedded applications featuring a high level of integration and low power consumption. The ARM Cortex-M3 is a next generation core that offers system enhancements such as enhanced debug features and a Higher level of support block integration.
