設計功率MOSFET驅動電路時需重點考慮寄生參數對電路的影響。米勒電容作為MOSFET器件的一項重要參數,在驅動電路的設計時需要重點關注。重點觀察了MOSFET的開通和關斷過程中柵極電壓、漏源極電壓和漏源極電流的變化過程,并分析了米勒電容、寄生電感等寄生參數對漏源極電壓和漏源極電流的影響。分析了柵極電壓在米勒平臺附近產生振蕩的原因,并提出了抑制措施,對功率MOSFET的驅動設計具有一定的指導意義。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an IMPortant parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
標簽： mosfet
上傳時間： 2022-04-02
上傳用戶：默默
電學中的測量技術涉及范圍非常廣,電流測量在電學計量中占有非常重要的位置。如何精確地進行電流測量是精密測量的一大難題。傳統的電流檢測電路多采用運算放大芯片與片外電流檢測電路相結合的方式,電路集成度很低,需要較多的接口和資源才能完成對電路的檢測。本文把所有電路部分都集成在一塊芯片上,包括檢測電阻,運算放大器電路及模擬轉數字轉換電路,從而在電路內部可以進行電流檢測,使電路更好的集成化。前置電路使用二級共源共柵結構的運算放大器,減小溝道長度調制效應造成的電流誤差。10位SAR ADC中采用電容驅動能力強的傳輸門保證了模數轉化器的有效精度。比較器模塊采用再生鎖存器與遲滯比較器作為基礎單元組合解決精密測量的問題。本設計可以作為嵌入芯片內的一小部分而檢測芯片中的微小電流1mA~100mA,工作電壓在1.8v左右,電流檢測精度預期達到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very IMPortant position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the requirement of 10 uA.
上傳時間： 2022-04-03
上傳用戶：
以單片機控制A/D轉換器TLC549為例,對A/D轉換器的主要技術指標進行了分析研究,在Proteus平臺下,完成了A/D轉換電路的構建,采用器件工作時序方式進行程序編寫,借助仿真圖表、虛擬儀器等工具對A/D轉換的數據進行測量并對失調誤差、增益誤差、微分非線性、積分非線性和轉換時間等重要參數進行了詳細分析。結果表明:使用Proteus軟件可對A/D轉換過程進行定性分析,將抽象的A/D轉換器技術指標直觀化、形象化展現出來,有助于學生更好地理解A/D轉換過程。The main technical indicators of A/D converter were analyzed and studied with an example from A/D converter TLC2543 which is controlled by using SCM.It was completed the construction of the A/D converter circuit under the Proteus software.The programming based on the operation sequence of the chip is put forward.With the aid of the simulation tools such as virtual instrument,simulation charts provided by Proteus,the IMPortant parameters of circuit such as offset error,gain error,differential nonlinearity(DNL),integral nonlinearity (INL) and conversion time are analyzed detailedly.Simulation results show that the A/D conversion process can be qualitatively analyzed and visualized the abstract indicators of A/D.The system can help students better to understand the SCM conversion process.
上傳時間： 2022-04-04
上傳用戶：
實驗教學一直是工科教學中不可或缺的組成部分,對培養學生的動手能力,獨立思考能力,創新思維與發散思維具有重要的作用。針對目前電路教學實驗中電路仿真實驗與實物電路實驗各自獨立,無法統一問題,提出將仿真電路實驗與實物電路實驗有機的結合同步操作,并使用Web發布實現遠程實驗操作。采用Multisim作為電路實驗仿真平臺,NI Eiviss II作為實物電路實驗硬件平臺,運用LabVIEW整合Multisim電路仿真實驗與實物電路實驗,實現仿真與實物實驗有機結合,兩種實驗可同步進行。學生在仿真實驗中先可探索實驗,然后做實物實驗。同時運用LabVIEW開發出實驗過程人機交互操作接口界面,使用過程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an IMPortant role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上傳時間： 2022-04-05
上傳用戶：
為適應雙向DC/DC功率變換的電流采樣需求,一種高精度高邊電流采樣電路被提出。其基本思想是在功率電路的高邊串入采樣電阻,借助電流鏡原理并引入偏置電流電路,將雙向電流均轉換為正向電壓輸出。通過理論分析與仿真結合的方法對電流鏡采樣原理及4種不同的偏置電流電路方案進行對比,最后通過實驗數據驗證了高精度高邊電流采樣電路的有效性。實驗數據表明,該采樣電路可在-25~75℃的溫度工作范圍內,針對-10~＋10 A范圍內的電流采樣實現優于5%的采樣精度。Current sensing plays an IMPortant role in controlling,monitoring or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...
上傳時間： 2022-04-22
上傳用戶：
隨著科技的發展，人們在日常生活中使用的電器越來越多，電子設備的電磁兼容性（EMC）也越來越重要。所以，人們對電子設備的電磁兼容性的要求也越來越嚴格，越來越規范。而在市場競爭中，如何降低成本、減少設備體積，是各電子設備制造廠家重點研究的課題。通過對開關電源的EMI濾波電路的類別和相應的技術特點進行分析，設計出一種既能提高性能，又能降低成本的濾波電路。With the development of technology, appliances people use in their daily lives, more and more electronic devices electromagnetic compatibility （ EMC ） has become increasingly IMPortant. So, people electromagnetic compatibility requirements of electronic devices have become increasingly stringent, more and more standardized. The competition in the market, how to reduce costs, reduce equipment size, is the subject of the electronic equipment manufacturer focused on research. Through the technical characteristics of the respective category and the EMI filter circuit switching power supply is analyzed both designed to improve a performance of the filter circuit can reduce the cost.
上傳時間： 2022-04-23
上傳用戶：
超聲波換能器作為一種實用的檢測手段，能實現聲波所攜帶的信息和電能之間轉換。它的性能優良，價格低廉，操作方便，易于調試，因此在工農業生產中發揮著重要的作用。但目前換能器驅動電路的發射頻率多為40 kHz，本文針對1 MHz的超聲波換能器電路進行了設計，主要介紹了它的發射驅動電路和接收驅動電路的設計方案，并對它們的功能進行了詳細地說明。最后搭建實驗平臺，并對電路的輸入、輸出模塊進行了測試。實驗結果表明，換能器電路運行良好，可以為超聲波高精度測量領域的應用提供參考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an IMPortant role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
上傳時間： 2022-04-28
上傳用戶：
This manual documents the Microcontroller profile of version 7 of the ARM? Architecture, the ARMv7-M architecture profile. For short definitions of all the ARMv7 profiles see About the ARMv7 architecture, and architecture profiles on page A1-20.ARMv7 is documented as a set of architecture profiles. The profiles are defined as follows: ARMv7-A The application profile for systems supporting the ARM and Thumb instruction sets, and requiring virtual address support in the memory management model. ARMv7-R The realtime profile for systems supporting the ARM and Thumb instruction sets, and requiring physical address only support in the memory management model ARMv7-M The microcontroller profile for systems supporting only the Thumb instruction set, and where overall size and deterministic operation for an implementation are more IMPortant than absolute performance. While profiles were formally introduced with the ARMv7 development, the A-profile and R-profile have implicitly existed in earlier versions, associated with the Virtual Memory System Architecture (VMSA) and Protected Memory System Architecture (PMSA) respectively.
標簽： arm
上傳時間： 2022-06-02
上傳用戶：
Mathematical modeling has become an IMPortant part of the research and devclopment work in engineering and scicnce. Retaining a competitive edge requiresa fast path between ideas and prototypes, and in this regard mathematical modeling and simulation provide a valuable shortcut for understanding both qualitative and quantitative aspects of scientific and engineering design. To assist you in gaining this edge, COMSOL Multiphysics offers state-of-the art performance, being built from the ground up with a Java3D interface and C/C++ solvers.The Acoustics Module is an optional package that extends the COMSOL Multiphysicsmodcling cnvironment with customized user interfaces and functionality optimizcd for the analysis of acoustics. Like all modules in the COMSOL family, it provides a brary of prewritten ready-to-run models that make it quicker and casier to analyze disciplinc-specific problcms.
上傳時間： 2022-06-19
上傳用戶：
PrefaceDuring the past years, there has been a quickly rising interest in radio access technologies for providingmobile as well as nomadic and fixed services for voice, video, and data. The difference indesign, implementation, and use between telecom and datacom technologies is also becoming moreblurred. One example is cellular technologies from the telecom world being used for broadband dataand wireless LAN from the datacom world being used for voice-over IP.Today, the most widespread radio access technology for mobile communication is digital cellular,with the number of users passing 5 billion by 2010, which is more than half of the world’s population.It has emerged from early deployments of an expensive voice service for a few car-borne users,to today’s widespread use of mobile-communication devices that provide a range of mobile servicesand often include camera, MP3 player, and PDA functions. With this widespread use and increasinginterest in mobile communication, a continuing evolution ahead is foreseen.This book describes LTE, developed in 3GPP (Third Generation Partnership Project) and providingtrue 4G broadband mobile access, starting from the first version in release 8 and through the continuingevolution to release 10, the latest version of LTE. Release 10, also known as LTE-Advanced,is of particular interest as it is the major technology approved by the ITU as fulfilling the IMTAdvancedrequirements. The description in this book is based on LTE release 10 and thus provides acomplete description of the LTE-Advanced radio access from the bottom up.Chapter 1 gives the background to LTE and its evolution, looking also at the different standardsbodies and organizations involved in the process of defining 4G. It also gives a discussion of the reasonsand driving forces behind the evolution.Chapters 2–6 provide a deeper insight into some of the technologies that are part of LTE and itsevolution. Because of its generic nature, these chapters can be used as a background not only for LTEas described in this book, but also for readers who want to understand the technology behind othersystems, such as WCDMA/HSPA, WiMAX, and CDMA2000.Chapters 7–17 constitute the main part of the book. As a start, an introductory technical overviewof LTE is given, where the most IMPortant technology components are introduced based onthe generic technologies described in previous chapters. The following chapters provide a detaileddescription of the protocol structure, the downlink and uplink transmission schemes, and the associatedmechanisms for scheduling, retransmission and interference handling. Broadcast operation andrelaying are also described. This is followed by a discussion of the spectrum flexibility and the associated
上傳時間： 2022-07-08
上傳用戶：
