<strike id="ew24i"></strike>
<strike id="ew24i"></strike>
The IA-32 Software Developer’s Manual, Volume 3: System Programming Guide (Order Number 245472), is part of a three-volume set that describes the architecture and programming environment of all IA-32 Intel® Architecture processors. The IA-32 Software Developer’s Manual, Volume 3, describes the operating-system support environment of an IA-32 processor, including memory management, protection, task management, INTerrupt and exception handling, and system management mode. It also provides IA-32 processor compatibility information. This volume is aimed at operating- system and BIOS designers and programmers.
標簽： Programming Developer Software 245472
上傳時間： 2013-12-23
上傳用戶：小碼農lz
This example demonstrates how the C8051F06x SMBus interface can communicate // with a 256 byte I2C Serial EEPROM (Microchip 24LC02B). // - INTerrupt-driven SMBus implementation // - Only master states defined (no slave or arbitration) // - Timer4 used by SMBus for SCL low timeout detection // - SCL frequency defined by <SMB_FREQUENCY> constant
標簽： demonstrates communicate C8051F06x interface
上傳時間： 2016-04-12
上傳用戶：hanli8870
This will sample all 8 A/D-channels by the continous mode. Each end of conversion will call an INTerrupt routine, where the AD-channel is put to Port4[2..0] and the upper nibble of the result is put to Port4[7..4]. Port 4 is connected to the user LEDs of the FlashCan100P Evaluation-Board
標簽： will D-channels conversion continous
上傳時間： 2013-12-09
上傳用戶：zm7516678
This example provides a description of how to set a communication with the bxCAN in loopback mode: - transmit and receive a standard data frame by polling at 100Kbit/S - transmit and receive an extended data frame with INTerrupt at 500Kbit/S - lit some LEDs depending of the program succeed or not
標簽： communication description provides loopback
上傳時間： 2016-04-24
上傳用戶：frank1234
This example provides a description of how to use a DMA channel to transfer a word data buffer from memory (Flash) to memory (RAM). The dedicated DMA channel is configured to transfer once a time a 32 word data buffer stored as constant in the Flash memory to another buffer in the RAM memory. The received data are stored in the DST_Buffer. The DMA channel transfer complete INTerrupt is enabled to generate an INTerrupt at the end of the buffer transfer. As soon as the transfer is completed an INTerrupt is generated and in the DMA channel INTerrupt routine the transfer complete INTerrupt pending bit is cleared. The data counter is stored before and after the transfer to show that all data has been transfered. TransferStatus gives the data transfer status where it is PASSED if transmitted and received data are the same otherwise it is FAILED
標簽： description provides transfer example
上傳時間： 2016-04-24
上傳用戶：ecooo
This example project shows how to use the IAR Embedded Workbench for ARM to develop code for the IAR-STM32-SK evaluation board. It shows basic use of I/O, timer and the INTerrupt controllers. Displays running lights on the board LED s.
標簽： Workbench for the Embedded
上傳時間： 2013-12-20
上傳用戶：Breathe0125
A huge program that consist of polling mechanism of a main controller to 32 slave in a fireman intercom environment. Including the handset condition detection, LCD controller, keypad controller, INTerrupt handling and ADC.
標簽： controller mechanism consist fireman
上傳時間： 2016-06-19
上傳用戶：璇珠官人
fft源代碼,#include "f2407_c.h" #include "math.h" #define N 32 // FFT變換的點數 extern void fft(void)； extern void resave(void)； INTerrupt void phantom(void)； void sysinit(void)； extern int input[2*N]；
上傳時間： 2016-06-28
上傳用戶：LouieWu
S3C2410開發實驗源代碼及實驗指導；內容包括： LED_ON LED_ON_C IO_ports arm-linux-ld memory_controller Nand Flash controller uart printf,scanf INTerrupt controller timer mmu clock vivi等； 主要講述了單片機s3c2410的使用。
標簽： memory_controller arm-linux-ld IO_ports LED_ON_C
上傳時間： 2013-12-21
上傳用戶：851197153
s3c2410嵌入式引導程序vivi中的驅動部分，已分成單個的實驗，包括mmu、sdram、uart、timer、INTerrupt等，可按每個實驗單獨學習一個內容
上傳時間： 2016-07-21
上傳用戶：GavinNeko
