On the design of an FPGA-Based OFDM modulator for IEEE 802.11a
標簽： FPGA-Based modulator 802.11 design
上傳時間： 2013-09-02
上傳用戶：zjwangyichao
POWER PCB轉PROTEL的方法，詳細說明了其轉換過程。
上傳時間： 2013-09-11
上傳用戶：cjl42111
power pcb To protel 軟件
上傳時間： 2013-09-11
上傳用戶：sunshine1402
protel s help on line
上傳時間： 2013-09-18
上傳用戶：iswlkje
The trend in ADCs and DACs is toward higher speeds and higher resolutions atreduced power levels. Modern data converters generally operate on ±5V (dualsupply) or +5V (single supply). In fact, many new converters operate on a single +3Vsupply. This trend has created a number of design and applications problems whichwere much less important in earlier data converters, where ±15V supplies and ±10Vinput ranges were the standard.
上傳時間： 2013-11-16
上傳用戶：sjw920325
Abstract: This tutorial discusses proper printed-circuit board (PCB) grounding for mixed-signal designs. Formost applications a simple method without cuts in the ground plane allows for successful PCB layouts withthis kind of IC. We begin this document with the basics: where the current flows. Later, we describe how toplace components and route signal traces to minimize problems with crosstalk. Finally, we move on toconsider power supply-currents and end by discussing how to extend what we have learned to circuits withmultiple mixed-signal ICs.
上傳時間： 2013-11-04
上傳用戶：pol123
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上傳時間： 2013-10-09
上傳用戶：yepeng139
Recently a new technology for high voltage Power MOSFETshas been introduced – the CoolMOS™ . Based on thenew device concept of charge compensation the RDS(on) areaproduct for e.g. 600V transistors has been reduced by afactor of 5. The devices show no bipolar current contributionlike the well known tail current observed during the turn-offphase of IGBTs. CoolMOS™ virtually combines the lowswitching losses of a MOSFET with the on-state losses of anIGBT.
標簽： COOLMOS
上傳時間： 2013-11-14
上傳用戶：zhyiroy
Abstract: This application note presents an overview of the operational characteristics of accurate I²C real-time clocks (RTCs),including the DS3231, DS3231M, and DS3232. It focuses on general application guidelines that facilitate use of device resources forpower management, I²C communication circuit configurations, and I²C characteristics relative to device power-up sequences andinitializations. Additional discussions on decoupling are provided to support developing strategies for mitigating power-supply pushingof device frequency.
上傳時間： 2013-11-23
上傳用戶：WMC_geophy
設計了水聲信號發生系統中的功率放大電路，可將前級電路產生的方波信號轉換為正弦信號，同時進行濾波、功率放大，使其滿足換能器對輸入信號的要求。該電路以單片機AT89C52，集成6階巴特沃思低通濾波芯片MF6以及大功率運算放大器LM12為核心，通過標準RS232接口與PC進行通信，實現信號增益的程控調節，對干擾信號具有良好的抑制作用。經調試該電路工作穩定正常，輸出波形無失真，在輸出功率以及放大增益、波紋系數等方面均滿足設計要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上傳時間： 2013-11-20
上傳用戶：qwe1234
