<blockquote id="0wo2i"></blockquote> Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上傳時間： 2014-03-25
上傳用戶：yyyyyyyyyy
gcc 操作參數細解,程編人員在操作gcc時得以了解參數用意
上傳時間： 2015-10-20
上傳用戶：zhaiye
使用pic16f873晶片來設定adi的RGB轉HDMI的功能chip。最主要是裡面一些參數值的設定必須參考原廠的adi chip規格
上傳時間： 2016-07-17
上傳用戶：erkuizhang
使用16f873來設定adi的HDMI轉RGB的chip設定參數值。
上傳時間： 2013-12-17
上傳用戶：sqq
在做2維度樣本分類的過程中,若我們能事先畫出訓練樣本在空間中的分散情形,這將有助於我們在設定SVM分類器的參數C的取值範圍. 例如:若畫出的訓練樣本的散佈較分散,我們可以得知此時採用的參數值可以取在較大的範圍. 所以本程式也是讓想要畫出資料樣本在平面的散佈情形者之一各可行工具.
上傳時間： 2016-08-19
上傳用戶：sy_jiadeyi
VFD-A 內部的參數資料可使用內部 RS-485 串聯通訊介面，設定及修改並可控制交流電機驅動 器運轉及監測交流電機驅動器的運轉狀態，可提高自動化的能力。
上傳時間： 2013-12-24
上傳用戶：invtnewer
CAN BUS的參數和基本相關設定 基本的範例檔案
上傳時間： 2017-02-26
上傳用戶：shawvi
在dos 模式下利用COM port 的介面來讀取 GPS韌體版本並可在後面加參數去更改 COM port 的號碼
上傳時間： 2013-12-17
上傳用戶：ippler8
將AVRmega48的Timer、ADC、IO等初始參數寫成各種副程式，方便直接取用，不必再努力尋找要設定哪些參數。
上傳時間： 2013-12-19
上傳用戶：asdkin
確定SJA1000 CAN控制器的位定時參數_SJA1000weidingshi
上傳時間： 2016-11-24
上傳用戶：test1111
