摘要：68HC08系列單片機在運行程序時往往需要保存某些參數使其掉電不丟失，為節約成本提高可靠性，可以將這些參數保存在片內FLASH中。片內FLASH主要是用來保存用戶程序的，為避免在程序運行時往FLASH中寫入數據所導致的單片機復位，因此采用了調用芯片內部監控ROM中自帶的FLASH操作子程序的方法。該方法適用于所有68HC08系列片內含FLASH芯片的單片機，具有很高的實用性和應用前景。
上傳時間： 2013-10-12
上傳用戶：zfyiaaa
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上傳時間： 2013-10-26
上傳用戶：fengweihao158@163.com
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上傳時間： 2013-10-28
上傳用戶：13691535575
LM3S 系列微控制器Flash 存儲器應用
上傳時間： 2014-12-27
上傳用戶：weixiao99
摘要：MOTOROLA新推出的MC68HC908系列8位單片機，采用片內FLASH取代過去常的片內ROM或EPROM，使單片機具有了在線編程寫入或擦除的功能，其應用范圍和方便性也因此而大大增加了。
上傳時間： 2013-10-11
上傳用戶：haoxiyizhong
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上傳時間： 2013-11-15
上傳用戶：zouxinwang
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
標簽： PROGRAMMER-TO PICKIT 8482
上傳時間： 2013-10-29
上傳用戶：ca05991270
LM3S 系列微控制器Flash 存儲器應用 在眾多的單片機中都集成了 Flash 存儲器系統，該存儲器系統可用作代碼和數據的存儲。它在整個存儲器中所處的位置在最起始的位置，一般其起始地址從零開始。
上傳時間： 2013-10-09
上傳用戶：aix008
高可靠性8位/16位All flash MCU結構、特點及應用 目錄NEC的MCU產品系列介紹NEC “全閃存單片機” 的特點NEC 8位MCU產品NEC 8位MCU特色功能介紹NEC 16位MCU特色功能介紹
上傳時間： 2013-11-22
上傳用戶：ouyangmark
德州儀器 (TI) 宣布推出價格更低的、基于 Stellaris ARM Cortex™-M3 的全新微處理器產品，擴展了旗下微處理器 (MCU) 陣營，從而為開發人員滿足嵌入式設計需求提供了更高的靈活性。29 款全新 Stellaris MCU 包括針對運動控制應用、智能模擬功能以及擴展的高級連接選項等的獨特 IP，可為工業應用提供各種價格／性能的解決方案。此外，該產品系列還可提供更大范圍的存儲器引腳兼容以及最新緊湊型封裝，可顯著節省空間與成本。由于 Stellaris MCU 卓越的集成度已融入 TI 的規模效應之中，由此帶來的高效率可使整個 Stellaris 系列的價格平均下降 13%。TI 綜合 StellarisWare® 軟件可為每款器件提供支持，從而可加速能源、安全以及連接市場領域的應用開發。
上傳時間： 2013-11-02
上傳用戶：604759954
