Abstract: This application note describes how to create, build, and debug appliCations targeted for the MAXQ1050 RISC
標簽： MAXQ CrossStudio 1050 30
上傳時間： 2014-08-11
上傳用戶：qwerasdf
Abstract: Field-programmable gate arrays (FPGAs) are used in a wide variety of appliCations and end markets, including digital signalprocessing, medical imaging, and high-performance computing. This application note outlines the issues related to powering FPGAs.It also discusses Maxim's solutions for powering Xilinx® FPGAs.
上傳時間： 2013-12-16
上傳用戶：haohaoxuexi
This is the Xilinx Dual Processor Reference Designs suite. The designs illustrate a few differentdual-core architectures based on the MicroBlaze™ and PowerPC™ processors. The designsillustrate various concepts described in the Xilinx White Paper WP262 titled, “DesigningMultiprocessor Systems in Platform Studio”. There are simple software appliCations includedwith the reference designs that show various forms of interaction between the two processors.
上傳時間： 2013-10-29
上傳用戶：旭521
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in appliCations where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of appliCations, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive appliCations. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上傳時間： 2013-11-07
上傳用戶：swing
The CC1101 is a low-cost sub- 1 GHztransceiver designed for very low-powerwireless appliCations. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
上傳時間： 2013-11-12
上傳用戶：363186
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size appliCations, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control appliCations as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose appliCations. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上傳時間： 2014-12-30
上傳用戶：aysyzxzm
Abstract: The process of designing a radio system can be complex and often involves many project tradeoffs. Witha little insight, balancing these various characteristics can make the job of designing a radio system easier. Thistutorial explores these tradeoffs and provides details to consider for various radio appliCations. With a focus on theindustrial, scientific, medical (ISM) bands, the subjects of frequency selection, one-way versus two-way systems,modulation techniques, cost, antenna options, power-supply influences, effects on range, and protocol selectionare explored.
標簽： 無線
上傳時間： 2013-12-13
上傳用戶：eastgan
通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。 Abstract: y comparing characteristics and appliCations area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上傳時間： 2014-01-10
上傳用戶：gundan
The RT9018A/B is a high performance positive voltage regulator designed for use in appliCations requining very low Input voltage and very low dropout voltage at up to 3A(peak).
上傳時間： 2013-10-10
上傳用戶：geshaowei
