描述了NTC使用B值計算出實際溫度與輸出的電壓之間的關系。
標簽： ntc計算
上傳時間： 2022-06-15
上傳用戶：
BC20-TE-B NB-Iot 評估板評估板原廠原理圖V1.2。完整對應實物裝置。
上傳時間： 2022-06-17
上傳用戶：
ASR M08-B設置軟件 V3.2 arduino 2560+ASRM08-B測試程序 arduino UNO+ASRM08-B測試程序語音控制臺燈電路圖及C51源碼(不帶校驗碼) 繼電器模塊設置。 ASR M08-B是一款語音識別模塊。首先對模塊添加一些關鍵字，對著該模塊說出關鍵字，串口會返回三位的數，如果是返回特定的三位數字，還會引起ASR M08-B的相關引腳電平的變化。【測試】①打開“ASR M08-B設置軟件 V3.2.exe”。②選擇“串口號”、“打開串口”、點選“十六進制顯示”。③將USB轉串口模塊連接到語音識別模塊上。接線方法如下：語音模塊TXD --> USB模塊RXD語音模塊RXD --> USB模塊TXD語音模塊GND --> USB模塊GND語音模塊3V3 --> USB模塊3V3（此端為3.3V電源供電端。）④將模塊的開關撥到“A”端，最好再按一次上面的大按鈕（按一次即可，為了確保模塊工作在正確的模式）。⑤對著模塊說“開燈”、“關燈”模塊會返回“0B”、“0A”，表示正常(注意：0B對應返回值010，0B對應返回值010，返回是16進制顯示的嘛，設置的時候是10進制設置的)。
標簽： ASR M08-B
上傳時間： 2022-07-06
上傳用戶：aben
NCS8803 3.2.1 功能：是一顆將HDMI信號轉EDP信號的轉接芯片。其應用如下： 3.2.2產品特征 輸入：HDMI 輸出：Embedded-DisplayPort (eDP) EDP接口 1/2/4-lane eDP @ 1.62/2.7Gbps per lane HD to WQXGA (2560*1600) supported 內置EDP協議 HDMI Input HDMI 1.4a supported 支持RGB444/YCbCr444/YCbCr422 像素時鐘： 340MHz 支持雙通道音頻輸入； 參考時鐘 任何頻率，在19MHz到100MHz之間，單端時鐘輸入 內置5000 ppm SSC與否 通信方式 IIC 電源 1.2V core supply 2.5V or 3.3V IO supply 功耗：150Mw 封裝：QFN-56 (7mm x 7mm) 3.2.4 應用產品：廣告機，平板、醫療器械、車機、顯示器、小電視、車載電視等 3.2.5 應用平臺：RK、全志、M-star、炬力等 3.3.6 推廣注意事項A:確認客戶使用屏的分辨率，最常用的是1366x768@60Hz和1920x1080@60Hz BNCS8803支持4-lane DP / eDP輸出通常支持WQXGA所需 (2560 * 1600)及以上60 hz的幀速率 C.確認客戶的信號源，要是標準的HDMI信號,其他的都不行； D.此芯片支持縮放功能，分數縮放比例2:1至1:2； E、此芯片不是純硬件轉換芯片，需要通過IIC或者SPI進行初始化，初始化一般使用客戶CPU進行，這樣方便控制時序也節省成本，如果不使用客戶CPU進行初始化就要另外加MCU進行配置。 設計注意事項： A、NCS8801S設計的時候要特別注意輸入輸出的走線問題，要做好屏蔽以免信號受到干擾。 B、注意電源濾波 C、設計的時候預留LVDS信號要預留阻抗匹配電阻 D、設計的時候復位腳最好由客戶CPU的GPIO口進行控制，以便控制整個方案的時序，避免后面出現問題。
上傳時間： 2022-07-08
上傳用戶：
Many complex systems—such as telecom equipment,memory modules, optical systems, networking equipment,servers and base stations—use FPGAs and otherdigital ICs that require multiple voltage rails that muststart up and shut down in a specific order, otherwise theICs can be damaged. The LTC®2924 is a simple andcompact solution to power supply sequencing in a 16-pinSSOP package (see Figures 1 and 2).
上傳時間： 2013-10-29
上傳用戶：tonyshao
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上傳時間： 2013-10-16
上傳用戶：togetsomething
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上傳時間： 2013-11-24
上傳用戶：defghi010
As logic systems get larger and more complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
上傳時間： 2013-10-08
上傳用戶：zhqzal1014
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上傳時間： 2013-11-15
上傳用戶：han_zh
為了提高傳統溫度控制系統的性能，將PID控制理論與嵌入式系統相結合，采用瑞薩電子公司的H8S/2166作為核心處理器，AD公司的AD7705以及熱敏電阻溫度傳感器作為溫度檢測單元，利用4×6小鍵盤、LCD顯示器和S1D13305液晶控制器達到良好的人機交互，設計出了一個應用于化工領域的嵌入式實時溫度控制系統。相比于傳統溫度控制系統，該系統提供了更強的計算能力和可擴展能力，采用增量PID控制算法實現復雜控制。通過實驗，該系統能達到0.1 ℃的溫度控制精度以及小于120 s的溫度穩定時間。 Abstract: In order to improve the performance of conventional temperature control system， combining PID control theory with embedded systems， using the Renesas Electronics Corp. H8S/2166 micro-controller as a core processors， AD7705 and thermistor temperature sensor as a temperature detection unit and 4×6 small keyboard， LCD and S1D13305 LCD controller as a good human-computer interaction， this paper designed an embedded real-time temperature control system which is applied in chemical industry. Compared with conventional temperature control system， this system provides more computing power and extensibility， and adopts PID control algorithm for complex control. Through the experiment， the system can reach temperature control accuracy of 0.1 ℃ and temperature stabilization time of less than 120 seconds.
上傳時間： 2014-12-26
上傳用戶：003030
