-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
標簽：
Signal
Input
Fall
rise
上傳時間：
2013-10-23
上傳用戶：copu
-
FPGAs rise to meetincreasing DSP system
requirements
標簽：
meetincreasing
requirements
system
FPGAs
上傳時間：
2013-12-20
上傳用戶：498732662
-
Three-dimensional real-time graphics are a prevalent technology nowadays, thanks
to the steady rise of processing power and specialized graphics hardware. One of the
goals of computer graphics most sought after and difficult to achieve is to reproduce realistic outdoor environments featuring dense forests.
標簽：
Three-dimensional
technology
real-time
prevalent
上傳時間：
2014-01-15
上傳用戶：壞天使kk
-
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
標簽：
二極管
導通
開關穩壓器
上傳時間：
2013-10-10
上傳用戶：誰偷了我的麥兜
-
As logic systems get larger and more complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
標簽：
高效率
密度
多相轉換器
高電流
上傳時間：
2013-10-08
上傳用戶：zhqzal1014
-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
標簽：
C16x
微控制器
輸入信號
時序圖
上傳時間：
2014-04-02
上傳用戶：han_zh
-
多遠程二極管溫度傳感器-Design Considerations for pc thermal management
Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
標簽：
Considerat
Design
遠程
二極管
上傳時間：
2014-12-21
上傳用戶：ljd123456
-
The LT® 1529/LT1529-3.3/LT1529-5 are 3A low dropout
regulators with micropower quiescent current and shutdown.
The devices are capable of supplying 3A of output
current with a dropout voltage of 0.6V. Designed for use
in battery-powered systems, the low quiescent current,
50mA operating and 16mA in shutdown, make them an
ideal choice. The quiescent current is well controlled it
does not rise in dropout as it does with many other low
dropout PNP regulators.
標簽：
1529
micropower
regulators
quiescent
上傳時間：
2013-12-17
上傳用戶：qiao8960
-
Student status management system is development two aspects that typical information management system, IMS( MIS), its development includes primarily the background database creates with support and the front end applies the procedure.Creates to rise to the former request the consistency of data is strong with the integrity, the library that the safeness of data like.But request the latter very much to apply the procedure function complete, easy usage etc. characteristics.
標簽：
management
development
information
Student
上傳時間：
2015-11-01
上傳用戶：1101055045
-
Anyone who interacts with today s modern databases needs to know SQL (Structured Query Language), the standard language for generating, manipulating, and retrieving database information. In recent years, the dramatic rise in the popularity of relational databases and multi-user databases has fueled a healthy demand for application developers and others who can write SQL code efficiently and correctly.
標簽：
Structured
interacts
databases
Language
上傳時間：
2016-01-02
上傳用戶：qlpqlq
