在半導體制冷技術的工作性能及其優缺點研究的基礎上,設計了以單片機為核心控制元件,以TEC1-12706為執行元件的半導體制冷溫度控制系統。采用高精度分段式PID控制算法配合PWM輸出控制的方法實現溫度控制;選擇數字傳感器DS18B20為溫度檢測元件,還包含1602液晶顯示模塊、按鍵調整輸入模塊和H橋驅動模塊等。實際測試表明,該系統結構簡單易行,操作方便,工作性能優良,同時針對該系統專門設計的溫控算法,使半導體制冷器能更好地適應不同工況而充分發揮其制冷制熱工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM output control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test sHows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.
上傳時間： 2022-03-27
上傳用戶：
數字示波器功能強大,使用方便,但是價格相對昂貴。本文以Ti的MSP430F5529為主控器,以Altera公司的EP2C5T144C8 FPGA器件為邏輯控制部件設計數字示波器。模擬信號經程控放大、整形電路后形成方波信號送至FPGA測頻,根據頻率值選擇采用片上及片外高速AD分段采樣。FPGA控制片外AD采樣并將數據輸入到FIFO模塊中緩存,由單片機進行頻譜分析。測試表明:簡易示波器可以實現自動選檔、多采樣率采樣、高精度測頻及頻譜分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test sHows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上傳時間： 2022-03-27
上傳用戶：
在傳統智能小車驅動電路設計中,較多考慮使用直流電機還是步進電機,電機功率、能耗等性能參數。使用具有armCortexM4內核的STM32嵌入式平臺控制四輪的4個直流電機。文章基于PWM技術及PID算法,對四輪進行精準地速度、轉向及啟停控制,實驗表明此小車具有優越各種地形適應能力。In the traditional intelligent car drive circuit design,DC motor or stepping motor,motor power,energy consumption and other performance parameters are considered.The four DC motors with four wheels are controlled by STM32 embedded platform with arm Cortex M4 kernel.Based on the PWM technology and PID algorithm,the accurate ground speed,steering,and start-stop control of the four wheels are carried out.The experiment sHows that the vehicle has the superior adaptability to all kinds of terrains.
上傳時間： 2022-04-02
上傳用戶：
This example sHows how you can use signal functions in the Visiondebugger to simulate a signal that is coming into one of the analog inputs of the LPC21xx.The Measure example is described in detail in the Getting StartedUser's Guide.The MEASURE example program is available for several targets:Simulator: uVision Simulator for LPC2129MCB2100: Keil MCB2100 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN0 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no parity, 8-bits, 1 stop bit, flow control noneMCB2130: Keil MCB2130 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN1 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no parity, 8-bits, 1 stop bit, flow control none
標簽： dac8568
上傳時間： 2022-06-28
上傳用戶：
