?? crc.pin
字號:
-- Copyright (C) 1991-2004 Altera Corporation
-- Any megafunction design, and related netlist (encrypted or decrypted),
-- support information, device programming or simulation file, and any other
-- associated documentation or information provided by Altera or a partner
-- under Altera's Megafunction Partnership Program may be used only
-- to program PLD devices (but not masked PLD devices) from Altera. Any
-- other use of such megafunction design, netlist, support information,
-- device programming or simulation file, or any other related documentation
-- or information is prohibited for any other purpose, including, but not
-- limited to modification, reverse engineering, de-compiling, or use with
-- any other silicon devices, unless such use is explicitly licensed under
-- a separate agreement with Altera or a megafunction partner. Title to the
-- intellectual property, including patents, copyrights, trademarks, trade
-- secrets, or maskworks, embodied in any such megafunction design, netlist,
-- support information, device programming or simulation file, or any other
-- related documentation or information provided by Altera or a megafunction
-- partner, remains with Altera, the megafunction partner, or their respective
-- licensors. No other licenses, including any licenses needed under any third
-- party's intellectual property, are provided herein.
--
-- This is a Quartus II output file. It is for reporting purposes only, and is
-- not intended for use as a Quartus II input file. This file cannot be used
-- to make Quartus II pin assignments - for instructions on how to make pin
-- assignments, please see Quartus II help.
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
-- NC : No Connect. This pin has no internal connection to the device.
-- VCCINT : Dedicated power pin, which MUST be connected to VCC (1.5V).
-- VCCIO : Dedicated power pin, which MUST be connected to VCC
-- of its bank.
-- Bank 1: 3.3V
-- Bank 2: 3.3V
-- Bank 3: 3.3V
-- Bank 4: 3.3V
-- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND.
-- It can also be used to report unused dedicated pins. The connection
-- on the board for unused dedicated pins depends on whether this will
-- be used in a future design. One example is device migration. When
-- using device migration, refer to the device pin-tables. If it is a
-- GND pin in the pin table or if it will not be used in a future design
-- for another purpose the it MUST be connected to GND. If it is an unused
-- dedicated pin, then it can be connected to a valid signal on the board
-- (low, high, or toggling) if that signal is required for a different
-- revision of the design.
-- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins.
-- This pin should be connected to GND. It may also be connected to a
-- valid signal on the board (low, high, or toggling) if that signal
-- is required for a different revision of the design.
-- GND* : Unused I/O pin. This pin can either be left unconnected or
-- connected to GND. Connecting this pin to GND will improve the
-- device's immunity to noise.
-- RESERVED : Unused I/O pin, which MUST be left unconnected.
-- RESERVED_INPUT : Pin is tri-stated and should be connected to the board.
---------------------------------------------------------------------------------
Quartus II Version 4.2 Build 157 12/07/2004 SJ Full Version
CHIP "crc" ASSIGNED TO AN: EP1C20F400C8
Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment
-------------------------------------------------------------------------------------------------------------
GND : A1 : gnd : : : :
VCCINT : A2 : power : : 1.5V : :
GND : A3 : gnd : : : :
GND* : A4 : : : : 2 :
VCCIO2 : A5 : power : : 3.3V : 2 :
GND* : A6 : : : : 2 :
GND* : A7 : : : : 2 :
GND* : A8 : : : : 2 :
GND* : A9 : : : : 2 :
GND* : A10 : : : : 2 :
GND* : A11 : : : : 2 :
GND* : A12 : : : : 2 :
GND* : A13 : : : : 2 :
GND* : A14 : : : : 2 :
GND* : A15 : : : : 2 :
VCCIO2 : A16 : power : : 3.3V : 2 :
GND* : A17 : : : : 2 :
GND : A18 : gnd : : : :
VCCINT : A19 : power : : 1.5V : :
GND : A20 : gnd : : : :
VCCINT : B1 : power : : 1.5V : :
GND : B2 : gnd : : : :
GND* : B3 : : : : 2 :
GND* : B4 : : : : 2 :
GND* : B5 : : : : 2 :
GND* : B6 : : : : 2 :
GND* : B7 : : : : 2 :
GND* : B8 : : : : 2 :
GND* : B9 : : : : 2 :
GND* : B10 : : : : 2 :
GND* : B11 : : : : 2 :
GND* : B12 : : : : 2 :
GND* : B13 : : : : 2 :
GND* : B14 : : : : 2 :
GND* : B15 : : : : 2 :
GND* : B16 : : : : 2 :
GND* : B17 : : : : 2 :
GND* : B18 : : : : 2 :
GND : B19 : gnd : : : :
VCCINT : B20 : power : : 1.5V : :
GND : C1 : gnd : : : :
GND* : C2 : : : : 1 :
GND* : C3 : : : : 1 :
GND* : C4 : : : : 2 :
GND* : C5 : : : : 2 :
GND* : C6 : : : : 2 :
GND* : C7 : : : : 2 :
GND* : C8 : : : : 2 :
GND* : C9 : : : : 2 :
GND* : C10 : : : : 2 :
GND* : C11 : : : : 2 :
GND* : C12 : : : : 2 :
GND* : C13 : : : : 2 :
?? 快捷鍵說明
復制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號
Ctrl + =
減小字號
Ctrl + -