//說明：此程序用于展示，連續顯示一屏，在暫停數秒，再顯示下一屏，直到完，再重復開頭顯示
//此程序正確

#include <msp430x13x.h>
#include <math.h>
#include <stdlib.h>
#define uchar unsigned char
#define uint unsigned int

        uchar pre=0;
unsigned char hzdot[] = {

0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,
/*南   C3647 */
0x04,0xF4,0x14,0x54,0x74,0xDF,0x54,0x74,
0x54,0x14,0xF6,0x04,0x00,0x0F,0x00,0x01,
0x01,0x0F,0x01,0x01,0x05,0x08,0x07,0x00,

/*京   C3009 */
0x04,0x04,0x04,0x74,0x54,0x55,0xD6,0x54,
0x54,0x74,0x06,0x04,0x08,0x04,0x02,0x01,
0x04,0x08,0x07,0x00,0x01,0x02,0x06,0x00,

/*航   C2629 */
0x40,0xFC,0x56,0x45,0xFC,0x04,0x04,0xF5,
0x16,0xF4,0x04,0x04,0x08,0x07,0x01,0x08,
0x0F,0x00,0x0C,0x03,0x00,0x07,0x08,0x0E,

/*空   C3153 */
0x48,0x44,0xA4,0x94,0x84,0x85,0x86,0x94,
0x94,0xA4,0x64,0x0C,0x08,0x08,0x08,0x08,
0x08,0x0F,0x08,0x08,0x08,0x08,0x0C,0x08,


/*航   C2629 */
0x40,0xFC,0x56,0x45,0xFC,0x04,0x04,0xF5,
0x16,0xF4,0x04,0x04,0x08,0x07,0x01,0x08,
0x0F,0x00,0x0C,0x03,0x00,0x07,0x08,0x0E,

/*天   C4476 */
0x10,0x12,0x12,0x12,0x12,0xFE,0x92,0x12,
0x12,0x13,0x12,0x10,0x08,0x08,0x04,0x02,
0x01,0x00,0x00,0x01,0x02,0x04,0x0C,0x04,
/*大   C2083 */
0x08,0x08,0x08,0x08,0x88,0x7F,0x88,0x08,
0x08,0x08,0x0C,0x08,0x08,0x08,0x04,0x02,
0x01,0x00,0x00,0x01,0x02,0x04,0x0C,0x04,

/*學   C4907 */
0x20,0x18,0x29,0x2E,0x28,0xA9,0xAE,0x68,
0x2C,0x0B,0x98,0x08,0x01,0x01,0x01,0x01,
0x05,0x09,0x0F,0x01,0x01,0x01,0x01,0x01,
};




unsigned int hantemp[10];

void delay(long v)
{
        while(v!=0)v--;
}

void wcode(uchar c,uchar cs1,uchar cs2)
   {       
        //先片選：CS1，CS2
        //D/I=0
        //R-W=0
        //數據
        //E：0-1-0
        
        if(cs1==1)
            P3OUT|=BIT5;
            else  P3OUT&=~BIT5;
        if(cs2==1)
            P3OUT|=BIT6;
            else  P3OUT&=~BIT6;
        P3OUT&=~BIT2;
        P3OUT&=~BIT3;
        P2OUT=c;
        P3OUT&=~BIT4;
        delay(3);
        P3OUT|=BIT4;
        delay(3);
        P3OUT&=~BIT4;
        
   }

void wdata(uchar c,uchar cs1,uchar cs2)
   {
        //先片選：CS1，CS2   :P35,P36
        //D/I=1         :P32
        //R-W=0         :P33
        //數據          :P2
        //E：0-1-0      :P34
        
        if(cs1==1)
            P3OUT|=BIT5;
            else  P3OUT&=~BIT5;
        if(cs2==1)
            P3OUT|=BIT6;
            else  P3OUT&=~BIT6;
        P3OUT|=BIT2;
        P3OUT&=~BIT3;
        P2OUT=c;
        P3OUT&=~BIT4;
        delay(3);
        P3OUT|=BIT4;
        delay(3);
        P3OUT&=~BIT4;
   }

void set_startline(uchar i)
{
        i=0xc0+i;
        wcode(i,1,1);
}
void set_adr(uchar x,uchar y)
{
        x=x+0xb8;y=y+0x40;
        wcode(x,1,1);
        wcode(y,1,1);
}

void dison_off(uchar o)
{
        o=o+0x3e;
        wcode(o,1,1);
}

void reset(void)
{
        //RST=0,1       :P37
        P3OUT&=~BIT7;
        delay(50);
        P3OUT|=BIT7;
        delay(50);
}


void clr(void)
{ uchar loop,i;

	for(i=0;i<8;i++)
		{

		set_adr(i,0);
		set_startline(0);
		for(loop=0;loop<64;loop++)
			{ wdata(0xf,1,0);
			}

		set_adr(i,0);
		set_startline(0);
		for(loop=0;loop<64;loop++)
			{wdata(0,0,1);
			}

		 }
  }




void full(void)
{ uchar loop,i;

	for(i=0;i<8;i++)
		{
		set_adr(i,0);
		set_startline(0);
		for(loop=0;loop<64;loop++)
			{ wdata(0xff,1,0);
			}
		set_adr(i,0);
		set_startline(0);
		for(loop=0;loop<64;loop++)
			{wdata(0x10,0,1);
			}
		 }
  }


void han(uchar distype,uchar *p,uchar lline,uchar x)     /*  p,點陣開始，顯示開始行（0---3),開始列（0---9)*/
	{
	uchar i,y;
	uchar ss=0;
	if(x>4)
	    {
	    x=x-5;
	    ss=1;
            y=x*12;
	    }
           else y=4+x*12;
        if(distype==1)
          {
         	set_adr(2*lline,y);
	set_startline(0);
	for(i=0;i<12;i++)
		{
		wdata(*(p+i),!ss,ss);
		}
	set_adr(2*lline+1,y);
	set_startline(0);
	for(i=12;i<24;i++)
		{
		wdata(*(p+i),!ss,ss);
		}
          }
          else
          {
         	set_adr(2*lline,y);
	set_startline(0);
	for(i=0;i<12;i++)
		{
		wdata(~(*(p+i)),!ss,ss);
		}
	set_adr(2*lline+1,y);
	set_startline(0);
	for(i=12;i<24;i++)
		{
		wdata(~(*(p+i)),!ss,ss);
		}
          }


	}




void qq(void)
        {
            uchar i,ll,x;
            for(i=0;i<40;i++)
               {
                ll=i  /   10;
                x=i   %   10;
                han(1,hzdot+hantemp[i]*24,i/10,i%10);
                }
        }


interrupt[TIMERA0_VECTOR] void Timer_A (void)
{
  uchar x,i;
CCR0 += 5000;                // Add Offset to CCR0
 x=x+1;
 if(x==60)
       {
       x=0;
       for(i=0;i<40;i++)
         {hantemp[i]=i+pre*40;

         }
       pre=pre+1;
       }
   if(pre==6)
     pre=0;

}


main(void)
{
 	uchar i;
	 WDTCTL = WDTPW + WDTHOLD;        // Stop WDT
//         TACTL = TASSEL1 + TACLR;       // SMCLK, clear TAR
  //        CCTL0 = CCIE;                 // CCR0 interrupt enabled
    //      CCR0 = 5000;
     //     P1DIR |= BIT0;                // P1.0 output
      //    TACTL |= MC1;                 // Start Timer_A in continuous mode
        //  _EINT();                      // 
//        for(i=0;i<40;i++)
  //      hantemp[i]=i;
  

        for(i=0;i<40;i++)
         {hantemp[i]=i;
         }
        P2DIR=0xFF;  
        P3DIR=0XFF;
        reset();
	dison_off(1);
        clr();
        delay(50000);
        full();
        qq();
while(1)
        {
         delay(60000);
         dison_off(1);
        }
}