#include"iom16.h"

#ifndef __AD9851_CONFIG_H__
#define __AD9851_CONFIG_H__

/*************數據類型定義***************/
#define uchar unsigned char  
#define uint  unsigned int
#define FQ    1                       //所使用的晶振的頻率，單位為MHZ，
#define Fosc 20000000;                //接到DDS上的晶振的頻率



/************液晶接口定義***************/
#define RS_BIT PD6                    //RS接到PD6
#define RW_BIT PD5                    //RW接到PD5
#define EN_BIT PD4                    //EN接到PD4
#define LCD_CON_DDR  DDRD
#define LCD_CON_PORT PORTD
#define LCD_DATA_DDR DDRA             //PA為數據接口
#define LCD_DATA_PORT PORTA
#define LCD_DATA_PIN  PINA
#define RS_CLR PORTD &= ~(1 << RS_BIT)
#define RS_SET PORTD |= (1 << RS_BIT)
#define RW_CLR PORTD &= ~(1 << RW_BIT)
#define RW_SET PORTD |= (1 << RW_BIT)
#define EN_CLR PORTD &= ~(1 << EN_BIT)
#define EN_SET PORTD |= (1 << EN_BIT)

/***********液晶子程序定義****************/
/*顯示屏命令寫入函數*/
void LCD_write_com(unsigned char com);
void LCD_write_data(unsigned char data);
/*顯示屏清空顯示*/
void LCD_clear(void);
/*顯示屏字符串寫入函數*/
void showstring(unsigned char x,unsigned char y,unsigned char *s);
/*顯示屏單字符寫入函數*/
void showchar(unsigned char x,unsigned char y,unsigned char data);
/*顯示屏初始化函數*/
void LCD_init(void);
void delay_nus(unsigned int n);
void delay_nms(unsigned int n);


/************鍵盤接口定義*****************/
#define KEY_DDR   DDRB        
#define KEY_PORT  PORTB
#define KEY_PIN   PINB

/***********鍵盤子程序定義****************/
uchar get_key(void);
uchar key_scan(void);


/***********AD9851相關部分***************/
#define DDS_CON_DDR  DDRD
#define DDS_CON_DIR 0X8D
#define DDS_DATA_DDR DDRC
#define DDS_DATA_DIR 0X80
#define DDS_CON_PORT PORTD
#define DDS_DATA_PORT PORTC
#define DDS_CON_PIN  PIND
#define SET_DDS_REST DDS_CON_PORT|=(1<<7)  //RESET 接到PD7
#define CLR_DDS_REST DDS_CON_PORT&=~(1<<7)
#define SET_DDS_WCLK DDS_CON_PORT|=(1<<3)  //WCLK 接到PD3
#define CLR_DDS_WCLK DDS_CON_PORT&=~(1<<3) 
#define SET_DDS_FQUD DDS_CON_PORT|=(1<<2)  //FQUD 接到PD2
#define CLR_DDS_FQUD DDS_CON_PORT&=~(1<<2)
#define DDS_DATA_BIT PORTC_Bit7            //位操作

void set_dds_to_serial(void);              //相關控制端口初始化，將DDS轉為串行控制方式，并設置一個初始頻率
void write_word(uchar *s);                 //寫入控制字的子函數

#endif