?? testbnch.v
字號(hào):
end end while (rc < count) begin @(posedge clk); if (tc < count) begin // Firstly See if the Transmitter is ready if (UARTstatus1_txrdy == 1'b1) begin wdata = tdata[tc]; cpu_write(wdata); tc = tc + 1; end end // Now See if any received data if (UARTstatus2_rxrdy == 1'b1) begin cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end // Verify that correct data received begin passflag = 0; for(i = 0; i <= count - 1; i = i + 1) begin if (rdata[i] != tdata[i]) begin $display("THIS TEST IS FAILED\n"); $finish; end else begin passflag = passflag +1; if (passflag == count) begin $display("THIS TEST IS PASSED\n"); $display("-----------------------------------------------------"); end end end end $display("Setting UART1 Operating Mode 8 bit, parity disabled"); UARTconfig1_bit8 = 1'b1 ; UARTconfig1_parity_en = 1'b0 ; UARTconfig1_odd_n_even = 1'b1 ; $display("Setting UART2 Operating Mode 8 bit, parity disabled"); UARTconfig2_bit8 = 1'b1 ; UARTconfig2_parity_en = 1'b0 ; UARTconfig2_odd_n_even = 1'b1 ; repeat (10) @(posedge clk); begin if (FIFO_DEPTH_16 == 1) count = 16; else count = 256; end tc = 0; rc = 0; $display("Testing Continuous Data Stream UART1 to UART2"); // Initialiase test data begin for(i = 0; i <= count-1; i = i + 1) begin tdata[i] = i; end end while (rc < count) begin @(posedge clk); if (tc < count) begin // Firstly See if the Transmitter is ready if (UARTstatus1_txrdy == 1'b1) begin wdata = tdata[tc]; cpu_write(wdata); tc = tc + 1; end end // Now See if any received data if (UARTstatus2_rxrdy == 1'b1) begin cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end // Verify that correct data received begin passflag = 0; for(i = 0; i <= count - 1; i = i + 1) begin if (rdata[i] != tdata[i]) begin $display("THIS TEST IS FAILED\n"); $finish; end else begin passflag = passflag +1; if (passflag == count) begin $display("THIS TEST IS PASSED\n"); $display("-----------------------------------------------------"); end end end end $display("Setting UART1 Operating Mode 7 bit, parity disabled"); UARTconfig1_bit8 = 1'b0 ; UARTconfig1_parity_en = 1'b0 ; UARTconfig1_odd_n_even = 1'b1 ; $display("Setting UART2 Operating Mode 7 bit, parity disabled"); UARTconfig2_bit8 = 1'b0 ; UARTconfig2_parity_en = 1'b0 ; UARTconfig2_odd_n_even = 1'b1 ; repeat (10) @(posedge clk); begin if (FIFO_DEPTH_16 == 1) count = 16; else count = 128; end tc = 0; rc = 0; $display("Testing Continuous Data Stream UART1 to UART2"); // Initialiase test data begin for(i = 0; i <= count-1; i = i + 1) begin tdata[i] = i; end end while (rc < count) begin @(posedge clk); if (tc < count) begin // Firstly See if the Transmitter is ready if (UARTstatus1_txrdy == 1'b1) begin wdata = tdata[tc]; cpu_write(wdata); tc = tc + 1; end end // Now See if any received data if (UARTstatus2_rxrdy == 1'b1) begin cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end // Verify that correct data received begin passflag = 0; for(i = 0; i <= count - 1; i = i + 1) begin if (rdata[i] != tdata[i]) begin $display("THIS TEST IS FAILED\n"); $finish; end else begin passflag = passflag +1; if (passflag == count) begin $display("THIS TEST IS PASSED\n"); $display("-----------------------------------------------------"); end end end end //--------------------------------- // Testing PARITY ERROR Generations //--------------------------------- $display("Setting UART1 8bit, parity enabled, and even parity"); // UART1 8bit, parity enabled, and even parity UARTconfig1_bit8 = 1'b1 ; UARTconfig1_parity_en = 1'b1 ; UARTconfig1_odd_n_even = 1'b0 ; $display("Setting UART2 8bit, parity enabled, and odd parity"); // UART2 8bit, parity enabled, and odd parity UARTconfig2_bit8 = 1'b1 ; UARTconfig2_parity_en = 1'b1 ; UARTconfig2_odd_n_even = 1'b1 ; repeat (10) @(posedge clk); begin if (FIFO_DEPTH_16 == 1) count = 16; else count = 256; end $display("Testing parity error generation"); // Initialiase test data tc = 0; rc = 0; i = 0; begin for(i = 0; i <= count-1; i = i + 1) begin tdata[i] = i; par_err[i] = 0; end end while (rc < count) begin @(posedge clk); if (tc < count) begin // Firstly See if the Transmitter is ready if (UARTstatus1_txrdy == 1'b1) begin wdata = tdata[tc]; cpu_write(wdata); tc = tc + 1; end end if (RX_FIFO == 0) begin // Now See if any received data if (UARTstatus2_rxrdy == 1'b1) begin par_err[rc] = UARTstatus2_parity_err; cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end else begin if (UARTstatus2_parity_err == 1'b1) begin par_err[rc] = UARTstatus2_parity_err; cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end end begin passflag = 0; for(i = 0; i <= count - 1; i = i + 1) begin if (par_err[i] != 1) begin $display("THIS TEST IS FAILED\n"); $finish; end else begin passflag = passflag +1; if (passflag == count) begin $display("THIS TEST IS PASSED\n"); $display("-----------------------------------------------------"); end end end end $display("Setting UART1 8bit, parity enabled, and odd parity"); // UART1 8bit, parity enabled, and odd parity UARTconfig1_bit8 = 1'b1 ; UARTconfig1_parity_en = 1'b1 ; UARTconfig1_odd_n_even = 1'b1 ; $display("Setting UART2 8bit, parity enabled, and even parity"); // UART2 8bit, parity enabled, and even parity UARTconfig2_bit8 = 1'b1 ; UARTconfig2_parity_en = 1'b1 ; UARTconfig2_odd_n_even = 1'b0 ; repeat (10) @(posedge clk); begin if (FIFO_DEPTH_16 == 1) count = 16; else count = 256; end $display("Testing parity error generation"); // Initialiase test data tc = 0; rc = 0; i = 0; begin for(i = 0; i <= count-1; i = i + 1) begin tdata[i] = i; par_err[i] = 0; end end while (rc < count) begin @(posedge clk); if (tc < count) begin // Firstly See if the Transmitter is ready if (UARTstatus1_txrdy == 1'b1) begin wdata = tdata[tc]; cpu_write(wdata); tc = tc + 1; end end if (RX_FIFO == 0) begin // Now See if any received data if (UARTstatus2_rxrdy == 1'b1) begin par_err[rc] = UARTstatus2_parity_err; cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end else begin if (UARTstatus2_parity_err == 1'b1) begin par_err[rc] = UARTstatus2_parity_err; cpu_read; rdata[rc] = UARTstatus2_data_out; rc = rc + 1; end end end begin passflag = 0; for(i = 0; i <= count - 1; i = i + 1) begin if (par_err[i] != 1) begin $display("THIS TEST IS FAILED\n"); $finish;?? 快捷鍵說明
復(fù)制代碼
Ctrl + C
搜索代碼
Ctrl + F
全屏模式
F11
切換主題
Ctrl + Shift + D
顯示快捷鍵
?
增大字號(hào)
Ctrl + =
減小字號(hào)
Ctrl + -