/****************************************************************************************
*
*   Disclaimer   This software code and all associated documentation, comments or other 
*  of Warranty:  information (collectively "Software") is provided "AS IS" without 
*                warranty of any kind. MICRON TECHNOLOGY, INC. ("MTI") EXPRESSLY 
*                DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED 
*                TO, NONINFRINGEMENT OF THIRD PARTY RIGHTS, AND ANY IMPLIED WARRANTIES 
*                OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. MTI DOES NOT 
*                WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE 
*                OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. 
*                FURTHERMORE, MTI DOES NOT MAKE ANY REPRESENTATIONS REGARDING THE USE OR 
*                THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS, 
*                ACCURACY, RELIABILITY, OR OTHERWISE. THE ENTIRE RISK ARISING OUT OF USE 
*                OR PERFORMANCE OF THE SOFTWARE REMAINS WITH YOU. IN NO EVENT SHALL MTI, 
*                ITS AFFILIATED COMPANIES OR THEIR SUPPLIERS BE LIABLE FOR ANY DIRECT, 
*                INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES (INCLUDING, 
*                WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, 
*                OR LOSS OF INFORMATION) ARISING OUT OF YOUR USE OF OR INABILITY TO USE 
*                THE SOFTWARE, EVEN IF MTI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
*                DAMAGES. Because some jurisdictions prohibit the exclusion or 
*                limitation of liability for consequential or incidental damages, the 
*                above limitation may not apply to you.
*
*                Copyright 2003 Micron Technology, Inc. All rights reserved.
*
****************************************************************************************/

    // Timing parameters based on Speed Grade

                                          // SYMBOL UNITS DESCRIPTION
                                          // ------ ----- -----------
`ifdef sg5B                               //              Timing Parameters for -5B (CL = 3)
    parameter tCK              =     5.0; // tCK    ns    Nominal Clock Cycle Time
    parameter tDQSQ            =     0.4; // tDQSS  ns    DQS-DQ skew, DQS to last DQ valid, per group, per access    parameter tMRD             =    10.0; // tMRD   ns    Load Mode Register command cycle time
    parameter tRAP             =    15.0; // tRAP   ns    ACTIVE to READ with Auto precharge command
    parameter tRAS             =    40.0; // tRAS   ns    Active to Precharge command time
    parameter tRC              =    55.0; // tRC    ns    Active to Active/Auto Refresh command time
    parameter tRFC             =    70.0; // tRFC   ns    Refresh to Refresh Command interval time
    parameter tRCD             =    15.0; // tRCD   ns    Active to Read/Write command time
    parameter tRP              =    15.0; // tRP    ns    Precharge command period
    parameter tRRD             =    10.0; // tRRD   ns    Active bank a to Active bank b command time
    parameter tWR              =    15.0; // tWR    ns    Write recovery time
`else `ifdef sg6                          //              Timing Parameters for -6 (CL = 2.5)
    parameter tCK              =     6.0; // tCK    ns    Nominal Clock Cycle Time
    parameter tDQSQ            =     0.4; // tDQSS  ns    DQS-DQ skew, DQS to last DQ valid, per group, per access    parameter tMRD             =    12.0; // tMRD   ns    Load Mode Register command cycle time
    parameter tRAP             =    15.0; // tRAP   ns    ACTIVE to READ with Auto precharge command
    parameter tRAS             =    42.0; // tRAS   ns    Active to Precharge command time
    parameter tRC              =    60.0; // tRC    ns    Active to Active/Auto Refresh command time
    parameter tRFC             =    72.0; // tRFC   ns    Refresh to Refresh Command interval time
    parameter tRCD             =    15.0; // tRCD   ns    Active to Read/Write command time
    parameter tRP              =    15.0; // tRP    ns    Precharge command period
    parameter tRRD             =    12.0; // tRRD   ns    Active bank a to Active bank b command time
    parameter tWR              =    15.0; // tWR    ns    Write recovery time
`else `ifdef sg75E                        //              Timing Parameters for -75E (CL = 2)
    parameter tCK              =     7.5; // tCK    ns    Nominal Clock Cycle Time
    parameter tDQSQ            =     0.5; // tDQSS  ns    DQS-DQ skew, DQS to last DQ valid, per group, per access    parameter tMRD             =    15.0; // tMRD   ns    Load Mode Register command cycle time
    parameter tRAP             =    15.0; // tRAP   ns    ACTIVE to READ with Auto precharge command
    parameter tRAS             =    40.0; // tRAS   ns    Active to Precharge command time
    parameter tRC              =    60.0; // tRC    ns    Active to Active/Auto Refresh command time
    parameter tRFC             =    75.0; // tRFC   ns    Refresh to Refresh Command interval time
    parameter tRCD             =    15.0; // tRCD   ns    Active to Read/Write command time
    parameter tRP              =    15.0; // tRP    ns    Precharge command period
    parameter tRRD             =    15.0; // tRRD   ns    Active bank a to Active bank b command time
    parameter tWR              =    15.0; // tWR    ns    Write recovery time
`else `define sg75Z                       //              Timing Parameters for -75Z (CL = 2)
    parameter tCK              =     7.5; // tCK    ns    Nominal Clock Cycle Time
    parameter tDQSQ            =     0.5; // tDQSS  ns    DQS-DQ skew, DQS to last DQ valid, per group, per access    parameter tMRD             =    15.0; // tMRD   ns    Load Mode Register command cycle time
    parameter tRAP             =    20.0; // tRAP   ns    ACTIVE to READ with Auto precharge command
    parameter tRAS             =    40.0; // tRAS   ns    Active to Precharge command time
    parameter tRC              =    65.0; // tRC    ns    Active to Active/Auto Refresh command time
    parameter tRFC             =    75.0; // tRFC   ns    Refresh to Refresh Command interval time
    parameter tRCD             =    20.0; // tRCD   ns    Active to Read/Write command time
    parameter tRP              =    20.0; // tRP    ns    Precharge command period
    parameter tRRD             =    15.0; // tRRD   ns    Active bank a to Active bank b command time
    parameter tWR              =    15.0; // tWR    ns    Write recovery time
`endif `endif `endif
    // Size Parameters based on Part Width

`ifdef x4
    parameter ADDR_BITS        =      13; // Set this parameter to control how many Address bits are used
    parameter DQ_BITS          =       4; // Set this parameter to control how many Data bits are used
    parameter DQS_BITS         =       1; // Set this parameter to control how many DQS bits are used
    parameter DM_BITS          =       1; // Set this parameter to control how many DM bits are used
    parameter COL_BITS         =      12; // Set this parameter to control how many Column bits are used
`else `ifdef x8
    parameter ADDR_BITS        =      13; // Set this parameter to control how many Address bits are used
    parameter DQ_BITS          =       8; // Set this parameter to control how many Data bits are used
    parameter DQS_BITS         =       1; // Set this parameter to control how many DQS bits are used
    parameter DM_BITS          =       1; // Set this parameter to control how many DM bits are used
    parameter COL_BITS         =      11; // Set this parameter to control how many Column bits are used
`else `define x16
    parameter ADDR_BITS        =      13; // Set this parameter to control how many Address bits are used
    parameter DQ_BITS          =      16; // Set this parameter to control how many Data bits are used
    parameter DQS_BITS         =       2; // Set this parameter to control how many DQS bits are used
    parameter DM_BITS          =       2; // Set this parameter to control how many DM bits are used
    parameter COL_BITS         =      10; // Set this parameter to control how many Column bits are used
`endif `endif

    parameter full_mem_bits    = 2+ADDR_BITS+COL_BITS; // Set this parameter to control how many unique addresses are used
    parameter part_mem_bits    = 10;                   // Set this parameter to control how many unique addresses are used    parameter no_halt          =       1; // If set to 1, the model won't halt on command sequence/major errors    parameter Debug            =       1; // Turn on debug message