HIGH SPEED 8051 μC CORE
- Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2
System Clocks
- Up to 25MIPS Throughput with 25MHz System Clock
- 22 Vectored Interrupt Sources
MEMORY
- 4352 Bytes Internal Data RAM (256 + 4k)
- 64k Bytes In-System Programmable FLASH Program Memory
- External Parallel Data Memory Interface – up to 5Mbytes/sec
DIGITAL PERIPHERALS
- 64 Port I/O; All are 5V tolerant
- Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial
Ports Available Concurrently
- Programmable 16-bit Counter/Timer Array with 5 Capture/Compare
Modules
- 5 General Purpose 16-bit Counter/Timers
- Dedicated Watch-Dog Timer; Bi-directional Reset
CLOCK SOURCES
- Internal Programmable Oscillator: 2-to-16MHz
- External Oscillator: Crystal, RC, C, or Clock
- Real-Time Clock Mode using Timer 3 or PCA
SUPPLY VOLTAGE ........................ 2.7V to 3.6V
- Typical Operating Current: 10mA @ 25MHz
- Multiple Power Saving Sleep and Shutdown Modes
100-Pin TQFP (64-Pin Version Available)
Temperature Range: –40°C to +85°C
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸?shù)慕涌陔娐吩韴D。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。
Abstract:
In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。
Abstract:
Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
