特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 前置量設定功能(二段設定)可選擇 數位化指撥設定操作簡易 計數暫時停止功能 3組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
標簽：
72
mm
微電腦
計數器
上傳時間：
2013-11-12
上傳用戶：909000580
Single-Ended and Differential S-Parameters
Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
標簽：
差分電路
單端
模式
上傳時間：
2014-03-25
上傳用戶：yyyyyyyyyy
PCB Layout Rule Rev1.70, 規範內容如附件所示, 其中分為:
(1) ”PCB LAYOUT 基本規範”:為R&D Layout時必須遵守的事項, 否則SMT,DIP,裁板時無法生產.
(2) “錫偷LAYOUT RULE建議規範”: 加適合的錫偷可降低短路及錫球.
(3) “PCB LAYOUT 建議規範”:為製造單位為提高量產良率,建議R&D在design階段即加入PCB Layout.
(4) ”零件選用建議規範”: Connector零件在未來應用逐漸廣泛, 又是SMT生產時是偏移及置件不良的主因,故製造希望R&D及採購在購買異形零件時能顧慮製造的需求, 提高自動置件的比例.
標簽：
LAYOUT
PCB
設計規范
上傳時間：
2013-11-03
上傳用戶：tzl1975
