介紹了以AVR單片機ATmega16為核心，采用前端信號調理電路、程控增益放大器以及波形顯示LCD（GDM12864A）實現的一個簡易示波器。并給出該系統設計的硬件和軟件設計方案。
Abstract:
Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR microcontroller ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,gain-programmed amplifier circuit and LCD’s interface circuit and so on.
為了解決磁放大器性能測試過程中，需要對其供給不同數值恒定電流的問題，設計了一種基于DAC7512和單片機的數控恒流源系統。該系統采用AT89C51作為主控器件，將計算機發送的電流控制字命令轉換為D/A轉換器控制字，通過模擬SPI通信接口，寫D/A控制字到DAC7512，從而控制其輸出相應數字電壓值，經差動縮放電路、電壓/電路變換電路和功率驅動電路，最后輸出恒定電流。實驗結果表明，恒流源輸出電流調節范圍為-45~+45 mA、精度為±0.1 mA，分辨率達0.024 4 mA，具有應用靈活，外圍電路簡單，可靠性高的特點。該數控直流恒流源也可為相關產品的測試系統研發提供參考。
Abstract:
In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。
Abstract:
In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
