便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。 微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。 Abstract: Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
上傳時間： 2013-11-19
上傳用戶：moerwang
為了使音頻信號分析儀小巧可靠，成本低廉，設計了以2片MSP430F1611單片機為核心的系統。該系統將音頻信號送入八階巴特沃茲低通濾波器，對信號進行限幅放大、衰減、電平位移、緩沖，并利用一單片機負責對前級處理后的模擬信號進行采樣，將采集得到的音頻信號進行4 096點基2的FFT計算，并對信號加窗函數提高分辨率，另一單片機負責對信號的分析及控制顯示設備。此設計精確的測量了音頻信號的功率譜、周期性、失真度指標，達到較高的頻率分辨率，并能將測量結果通過紅外遙控器顯示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上傳時間： 2013-12-11
上傳用戶：jasonheung
在航電系統維護過程中，為解決定位故障的效率和降低維修成本等問題，提出了基于ICD（Interface Control Document，接口控制文件）的1553B總線的信息監控系統模型。該系統運用數據采集卡對總線中傳輸?shù)男盘栍袩o失真、偏差等電氣特性進行檢測，并使用1553B通訊卡通過測控軟件LabWindows/CVI編程與ICD數據庫的動態鏈接，實現總線信息的解析和故障的判斷。與傳統的維護過程相比，這種模型能夠從信號的電氣特性以及信息的解析等全方位的去檢測判斷故障的來源，并且能夠廣泛在其他1553B總線系統內擴展應用。驗證表明該監控系統可以對總線信息進行快速有效地監測分析，能滿足應用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
標簽： 1553B 總線 信息監控
上傳時間： 2013-11-23
上傳用戶：18752787361
第一章 概述 第二章 微型測控系統常用器件 第三章 工業控制計算技術要點 第四章 單片機存儲系統擴展 第五章 標準總線和串行通信 第六章微型機應用系統常用可編程接口芯片 ............................
上傳時間： 2014-01-09
上傳用戶：dbs012280
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
標簽： 單總線 無線溫度 采集 系統設計
上傳時間： 2013-10-29
上傳用戶：515414293
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸?shù)慕涌陔娐吩韴D。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
標簽： 工控軟件 單片機 串口通訊 多機
上傳時間： 2013-12-19
上傳用戶：tecman
介紹基于ISA總線與KH-9300的數據采集板卡的設置，詳細說明8254定時計數器及8259中斷控制器的結構特點、工作方式、控制字等，探討中斷類型、中斷處理程序、中斷矢量表及其填寫。重點講述使用TorboC編寫中斷服務程序的方法，應注意的主要問題及程序測試的結果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上傳時間： 2013-11-14
上傳用戶：qq527891923
介紹一種基于C8051F060單片機和NAND Flash的數據采集存儲系統，該系統可實現3路信號采樣，每路采樣率為5KS/s,通過異步串行通信接口實現數據傳輸。并詳細說明系統的軟件設計。 Abstract: An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
標簽： C8051F060 數據采集 存儲系統
上傳時間： 2013-10-12
上傳用戶：Jesse_嘉偉
摘要：本文介紹了C8051F系列單片機在遠端測控裝置中的應用，給出了整個系統的結構，包括硬件配置和系統網絡構成，對一些技術問題也做出了詳盡的說明。 關鍵詞：C8051F，遠端測控；硬件配置，單片機，SoC C8051F單片機是完全集成的混合信號系統芯片(SoC)，具有與8051指令集完全兼容的CIP-51內核和高速、高性能、高集成度等特點。在本文設計的一套遠端測控裝置中取得了較好的效果。
標簽： C8051F 單片機 中的應用 測控裝置
上傳時間： 2013-10-28
上傳用戶：s藍莓汁
TLC1543是TI公司推出的采用SPI技術的模數轉換器。具有輸入通道多、高速、高分辨率、性價比高、易于和單片機接口等特點，在各種數據采集系統中有著廣闊的應用空間。51單片機、TLC1543加上很少的外圍器件即可構成一個高性價比的數據采集系統，同時TLC1543占用單片機I/O資源較少，使得單片機有足夠的I/O資源去完成如控制、顯示等功能。由AT89C52和TLC1543構成的三相單獨可調400Hz中頻電源的數據采集系統在實際運用中達到很好的效果。
上傳時間： 2013-11-17
上傳用戶：xg262122
蟲蟲下載站版權所有 京ICP備2021023401號-1
