隨著單片機性能不斷提高而價格卻不斷下降, 單片機控制在越來越多的領域得以應用。按照傳統的模式, 在整個項目開發過程中, 先根據控制系統要求設計原理圖, PCB 電路圖繪制, 電路板制作, 元器件的焊接, 然后進行軟件編程, 通過仿真器對系統硬件和軟件調試, 最后將調試成功的程序固化到單片機中。這一過程中的主要問題是, 應用程序需要在硬件完成的情況下才能進行調試。雖然有的軟件可以進行模擬調試, 但是對于一些復雜的程序如人機交互程序, 在沒有硬件的時候, 沒有界面的真實感, 給調試帶來困難。在軟硬件的配合中如需要修改硬件, 要重新制板, 在時間和投入上帶來很大的麻煩?？v觀整個過程, 無論是從硬件成本上, 還是從調試周期上, 傳統開發模式的效率有待提高。能否只使用一種開發工具兼顧仿真, 調試, 制板, 以及最大限度的軟件模擬來作為單片機的開發平臺, 用它取代編程器、仿真器、成品前的硬件測試等工作是廣大單片機開發者的夢想。
PROTEUS 軟件介紹為了更加直觀具體地說明Proteus 軟件的實用價值, 本文以一具體的TAXI 的計價器和計時器電路板的設計過程為例。其電路板要實現的功能是:㈠計時功能(相當于時鐘);㈡里程計價功能:兩公里以?xún)?nèi)價格為4 元, 以后每一公里加0.7 元, 不足一公里取整(如10.3 公里取11 公里);㈢通過鍵盤輸入里程, 模擬計算里程費, 實現Y= (X- 2)*0.7+4 的簡單計算?；谏鲜龉δ? 選用ATMEL 公司生產的通用芯片AT89C51 單片機構成應用系統。AT89C51 是內含8 位4K 程序存儲器, 128B 數據存儲器, 2 個定時器/計數器的通用芯片。系統開發環境采用ProteusISIS 6。2.1 計價器模擬系統硬件構成系統主要由一個AT89C51 單片機、74LS373、74LS240、矩陣鍵盤、4 位7 段數碼管等組成。通用AT89C51 單片機芯片作為整個電路的核心部分、74LS373 作為L(zhǎng)ED 段選控制、74LS240四路反相器則為4 位共陰極7 段數碼管提供位選通信號、矩陣鍵盤輸入控制信號。
標簽：
Proteus
單片機
出租車計價器
上傳時間：
2013-11-09
上傳用戶：木子葉1
Single-Ended and Differential S-Parameters
Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
標簽：
差分電路
單端
模式
上傳時間：
2014-03-25
上傳用戶：yyyyyyyyyy
