本代碼為編碼開關代碼，編碼開關也就是數字音響中的 360度旋轉的數字音量以及顯示器上用的（單鍵飛梭開 關）等類似鼠標滾輪的手動計數輸入設備。 我使用的編碼開關為5個引腳的，其中2個引腳為按下 轉輪開關（也就相當于鼠標中鍵）。另外3個引腳用來 檢測旋轉方向以及旋轉步數的檢測端。引腳分別為a,b,c b接地a，c分別接到P2.0和P2.1口并分別接兩個10K上拉 電阻，并且a，c需要分別對地接一個104的電容，否則 因為編碼開關的觸點抖動會引起輕微誤動作。本程序不 使用定時器，不占用中斷，不使用延時代碼，并對每個 細分步數進行判斷，避免一切誤動作，性能超級穩定。 我使用的編碼器是APLS的EC11B可以參照附件的時序圖 編碼器控制流水燈最能說明問題，下面是以一段流水 燈來演示。
上傳時間： 2017-07-03
上傳用戶：gaojiao1999
/* ********************************************************************************************************* * uC/TCP-IP V2 * The Embedded TCP/IP Suite * * (c) Copyright 2003-2010; Micrium, Inc.; Weston, FL * * All rights reserved. Protected by international copyright laws. * * uC/TCP-IP is provided in source form to registered licensees ONLY. It is * illegal to distribute this source code to any third party unless you receive * written permission by an authorized Micrium representative. Knowledge of * the source code may NOT be used to develop a similar product. * * Please help us continue to provide the Embedded community with the finest * software available. Your honesty is greatly appreciated. * * You can contact us at www.micrium.com. ********************************************************************************************************* */ /* ********************************************************************************************************* * * NETWORK TCP LAYER * (TRANSMISSION CONTROL PROTOCOL) * * Filename : net_tcp.h * Version : V2.10 * Programmer(s) : ITJ ********************************************************************************************************* * Note(s) : (1) Supports Transmission Control Protocol as described in RFC #793 with the following * restrictions/constraints : * * (a) TCP Security & Precedence NOT supported RFC # 793, Section 3.6 * * (b) TCP Urgent Data NOT supported RFC # 793, Section 3.7 * 'The Communication of * Urgent Information' * * (c) The following TCP options NOT supported : * * (1) Window Scale RFC #1072, Section 2 * RFC #1323, Section 2 * (2) Selective Acknowledgement (SACK) RFC #1072, Section 3 * RFC #2018 * RFC #2883 * (3) TCP Echo RFC #1072, Section 4 * (4) Timestamp RFC #1323, Section 3.2 * (5) Protection Against Wrapped Sequences (PAWS) RFC #1323, Section 4 * * (d) #### IP-Options-to-TCP-Connection RFC #1122, Section 4.2.3.8 * Handling NOT supported * * (e) #### ICMP-Error-Message-to-TCP-Connection RFC #1122, Section 4.2.3.9 * Handling NOT currently supported * * (2) TCP Layer assumes/requires Network Socket Layer (see 'net_sock.h MODULE Note #1a2'). ********************************************************************************************************* */ /*$PAGE*/ /* ********************************************************************************************************* * MODULE * * Note(s) : (1) TCP Layer module is NOT required for UDP-to-Application API configuration. * * See also 'net_cfg.h TRANSPORT LAYER CONFIGURATION' * & 'net_cfg.h USER DATAGRAM PROTOCOL LAYER CONFIGURATION'. * * See also 'net_tcp.h Note #2'. * * (2) The following TCP-module-present configuration value MUST be pre-#define'd in * 'net_cfg_net.h' PRIOR to all other network modules that require TCP Layer * configuration (see 'net_cfg_net.h TCP LAYER CONFIGURATION Note #2b') : * * NET_TCP_MODULE_PRESENT ********************************************************************************************************* */ #ifdef NET_TCP_MODULE_PRESENT /* See Note #2. */ /* ********************************************************************************************************* * EXTERNS ********************************************************************************************************* */ #if ((defined(NET_TCP_MODULE)) && \ (defined(NET_GLOBALS_EXT))) #define NET_TCP_EXT #else #define NET_TCP_EXT extern #endif /*$PAGE*/ /* ********************************************************************************************************* * DEFINES ********************************************************************************************************* */ /* ********************************************************************************************************* * TCP HEADER DEFINES * * Note(s) : (1) The following TCP value MUST be pre-#define'd in 'net_def.h' PRIOR to 'net_buf.h' so that * the Network Buffer Module can configure maximum buffer header size (see 'net_def.h TCP * LAYER DEFINES' & 'net_buf.h NETWORK BUFFER INDEX & SIZE DEFINES Note #1') : * * (a) NET_TCP_HDR_SIZE_MAX 60 (NET_TCP_HDR_LEN_MAX * * NET_TCP_HDR_LEN_WORD_SIZE) * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_LEN_MASK 0xF000u #define NET_TCP_HDR_LEN_SHIFT 12u #define NET_TCP_HDR_LEN_NONE 0u #define NET_TCP_HDR_LEN_MIN 5u #define NET_TCP_HDR_LEN_MAX 15u #define NET_TCP_HDR_LEN_WORD_SIZE CPU_WORD_SIZE_32 #define NET_TCP_HDR_SIZE_MIN (NET_TCP_HDR_LEN_MIN * NET_TCP_HDR_LEN_WORD_SIZE) #if 0 /* See Note #1a. */ #define NET_TCP_HDR_SIZE_MAX (NET_TCP_HDR_LEN_MAX * NET_TCP_HDR_LEN_WORD_SIZE) #endif #define NET_TCP_HDR_SIZE_TOT_MIN (NET_IP_HDR_SIZE_TOT_MIN + NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_SIZE_TOT_MAX (NET_IP_HDR_SIZE_TOT_MAX + NET_TCP_HDR_SIZE_MAX) #define NET_TCP_PSEUDO_HDR_SIZE 12u /* = sizeof(NET_TCP_PSEUDO_HDR) */ #define NET_TCP_PORT_NBR_RESERVED NET_PORT_NBR_RESERVED #define NET_TCP_PORT_NBR_NONE NET_TCP_PORT_NBR_RESERVED #define NET_TCP_HDR_URG_PTR_NONE 0x0000u /* See Note #2. */ /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER FLAG DEFINES * * Note(s) : (1) See 'TCP HEADER Note #2' for flag fields. * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_FLAG_MASK 0x0FFFu #define NET_TCP_HDR_FLAG_NONE DEF_BIT_NONE #define NET_TCP_HDR_FLAG_RESERVED 0x0FE0u /* MUST be '0'. */ #define NET_TCP_HDR_FLAG_URGENT DEF_BIT_05 /* See Note #2. */ #define NET_TCP_HDR_FLAG_ACK DEF_BIT_04 #define NET_TCP_HDR_FLAG_PUSH DEF_BIT_03 #define NET_TCP_HDR_FLAG_RESET DEF_BIT_02 #define NET_TCP_HDR_FLAG_SYNC DEF_BIT_01 #define NET_TCP_HDR_FLAG_FIN DEF_BIT_00 #define NET_TCP_HDR_FLAG_CLOSE NET_TCP_HDR_FLAG_FIN /* ********************************************************************************************************* * TCP FLAG DEFINES ********************************************************************************************************* */ /* ------------------ NET TCP FLAGS ------------------- */ #define NET_TCP_FLAG_NONE DEF_BIT_NONE #define NET_TCP_FLAG_USED DEF_BIT_00 /* TCP conn cur used; i.e. NOT in free TCP conn pool. */ /* ------------------ TCP TX FLAGS ------------------- */ /* TCP tx flags copied from TCP hdr flags. */ #define NET_TCP_FLAG_TX_FIN NET_TCP_HDR_FLAG_FIN #define NET_TCP_FLAG_TX_CLOSE NET_TCP_FLAG_TX_FIN #define NET_TCP_FLAG_TX_SYNC NET_TCP_HDR_FLAG_SYNC #define NET_TCP_FLAG_TX_RESET NET_TCP_HDR_FLAG_RESET #define NET_TCP_FLAG_TX_PUSH NET_TCP_HDR_FLAG_PUSH #define NET_TCP_FLAG_TX_ACK NET_TCP_HDR_FLAG_ACK #define NET_TCP_FLAG_TX_URGENT NET_TCP_HDR_FLAG_URGENT #define NET_TCP_FLAG_TX_BLOCK DEF_BIT_07 /* ------------------ TCP RX FLAGS ------------------- */ #define NET_TCP_FLAG_RX_DATA_PEEK DEF_BIT_08 #define NET_TCP_FLAG_RX_BLOCK DEF_BIT_15 /*$PAGE*/ /* ********************************************************************************************************* * TCP TYPE DEFINES * * Note(s) : (1) NET_TCP_TYPE_&&& #define values specifically chosen as ASCII representations of the TCP * types. Memory displays of TCP types will display with their chosen ASCII names. ********************************************************************************************************* */ /* ------------------ NET TCP TYPES ------------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x20504354u /* "TCP " in ASCII. */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x43542050u /* "TCP " in ASCII. */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #endif #endif /* ********************************************************************************************************* * TCP SEQUENCE NUMBER DEFINES * * Note(s) : (1) TCP initial transmit sequence number is incremented by a fixed value, preferably a large * prime value or a large value with multiple unique factors. * * (a) One reasonable TCP initial transmit sequence number increment value example : * * 65527 = 37 * 23 * 11 * 7 * * * #### NET_TCP_TX_SEQ_NBR_CTR_INC could be developer-configured in 'net_cfg.h'. * * See also 'NET_TCP_TX_GET_SEQ_NBR() Notes #1b2 & #1c2'. ********************************************************************************************************* */ #define NET_TCP_SEQ_NBR_NONE 0u #define NET_TCP_ACK_NBR_NONE NET_TCP_SEQ_NBR_NONE #define NET_TCP_TX_SEQ_NBR_CTR_INC 65527u /* See Note #1. */ #define NET_TCP_ACK_NBR_DUP_WIN_SIZE_SCALE 4 /*$PAGE*/ /* ********************************************************************************************************* * TCP DATA/TOTAL LENGTH DEFINES * * Note(s) : (1) (a) TCP total length #define's (NET_TCP_TOT_LEN) relate to the total size of a complete * TCP packet, including the packet's TCP header. Note that a complete TCP packet MAY * be fragmented in multiple Internet Protocol packets. * * (b) TCP data length #define's (NET_TCP_DATA_LEN) relate to the data size of a complete * TCP packet, equal to the total TCP packet length minus its TCP header size. Note * that a complete TCP packet MAY be fragmented in multiple Internet Protocol packets. ********************************************************************************************************* */ /* See Notes #1a & #1b. */ #define NET_TCP_DATA_LEN_MIN 0u #define NET_TCP_TOT_LEN_MIN (NET_TCP_HDR_SIZE_MIN + NET_TCP_DATA_LEN_MIN) #define NET_TCP_TOT_LEN_MAX (NET_IP_TOT_LEN_MAX - NET_IP_HDR_SIZE_MIN ) #define NET_TCP_DATA_LEN_MAX (NET_TCP_TOT_LEN_MAX - NET_TCP_HDR_SIZE_MIN) /*$PAGE*/ /* ********************************************************************************************************* * TCP SEGMENT SIZE DEFINES * * Note(s) : (1) (a) RFC # 879, Section 3 states that the TCP Maximum Segment Size "counts only * data octets in the segment, ... not the TCP header or the IP header". * * (b) RFC #1122, Section 4.2.2.6 requires that : * * (1) "The MSS value to be sent in an MSS option must be less than or equal to * * (A) MMS_R - 20 * * where MMS_R is the maximum size for a transport-layer message that can * be received." * * (2) "If an MSS option is not received at connection setup, TCP MUST assume a * default send MSS of 536 (576 - 40)." * * See also 'net_ip.h IP DATA/TOTAL LENGTH DEFINES Note #1'. ********************************************************************************************************* */ /* See Note #1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT (NET_IP_MAX_DATAGRAM_SIZE_DFLT - NET_IP_HDR_SIZE_MIN - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_MAX_SEG_SIZE_DFLT_RX NET_TCP_DATA_LEN_MAX /* See Note #1b1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT_TX NET_TCP_MAX_SEG_SIZE_DFLT /* See Note #1b2. */ #define NET_TCP_MAX_SEG_SIZE_NONE 0u #define NET_TCP_MAX_SEG_SIZE_MIN NET_TCP_MAX_SEG_SIZE_DFLT #define NET_TCP_MAX_SEG_SIZE_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_MIN NET_TCP_DATA_LEN_MIN #define NET_TCP_SEG_LEN_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_SYNC 1u #define NET_TCP_SEG_LEN_FIN 1u #define NET_TCP_SEG_LEN_CLOSE NET_TCP_SEG_LEN_FIN #define NET_TCP_SEG_LEN_ACK 0u #define NET_TCP_SEG_LEN_RESET 0u #define NET_TCP_SEG_LEN_PROBE 0u #define NET_TCP_DATA_LEN_TX_SYNC 0u #define NET_TCP_DATA_LEN_TX_FIN 0u #define NET_TCP_DATA_LEN_TX_CLOSE NET_TCP_DATA_LEN_TX_FIN #define NET_TCP_DATA_LEN_TX_ACK 0u #define NET_TCP_DATA_LEN_TX_PROBE_NO_DATA 0u #define NET_TCP_DATA_LEN_TX_PROBE_DATA 1u #define NET_TCP_DATA_LEN_TX_RESET 0u #define NET_TCP_TX_PROBE_DATA 0x00u /* ********************************************************************************************************* * TCP WINDOW SIZE DEFINES * * Note(s) : (1) Although NO RFC specifies the absolute minimum TCP connection window size value allowed, * RFC #793, Section 3.7 'Data Communication : Managing the Window' states that for "the * window ... there is an assumption that this is related to the currently available data * buffer space available for this connection". ********************************************************************************************************* */ #define NET_TCP_WIN_SIZE_NONE 0u #define NET_TCP_WIN_SIZE_MIN NET_TCP_MAX_SEG_SIZE_MIN #define NET_TCP_WIN_SIZE_MAX DEF_INT_16U_MAX_VAL /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER OPTIONS DEFINES * * Note(s) : (1) See the following RFC's for TCP options summary : * * (a) RFC # 793, Section 3.1 'Header Format : Options' * (b) RFC #1122; Sections 4.2.2.5, 4.2.2.6 * * (2) TCP option types are encoded in the first octet for each TCP option as follows : * * -------- * | TYPE | * -------- * * The TCP option type value determines the TCP option format : * * (a) The following TCP option types are single-octet TCP options -- i.e. the option type * octet is the ONLY octet for the TCP option. * * (1) TYPE = 0 End of Options List * (2) TYPE = 1 No Operation * * * (b) All other TCP options MUST be multi-octet TCP options (see RFC #1122, Section 4.2.2.5) : * * ------------------------------ * | TYPE | LEN | TCP OPT | * ------------------------------ * * where * TYPE Indicates the specific TCP option type * LEN Indicates the total TCP option length, in octets, including * the option type & the option length octets * TCP OPT Additional TCP option octets, if any, that contain the remaining * TCP option information * * The following TCP option types are multi-octet TCP options where the option's second * octet specify the total TCP option length, in octets, including the option type & the * option length octets : * * (1) TYPE = 2 Maximum Segment Size See RFC # 793, Section 3.1 'Header Format : * Options : Maximum Segment Size'; * RFC #1122, Section 4.2.2.6; * RFC # 879, Section 3 * * (2) TYPE = 3 Window Scale See 'net_tcp.h Note #1c1' * (3) TYPE = 4 SACK Allowed See 'net_tcp.h Note #1c2' * (4) TYPE = 5 SACK Option See 'net_tcp.h Note #1c2' * (5) TYPE = 6 Echo Request See 'net_tcp.h Note #1c3' * (6) TYPE = 7 Echo Reply See 'net_tcp.h Note #1c3' * (7) TYPE = 8 Timestamp See 'net_tcp.h Note #1c4' * * (3) TCP header allows for a maximum option list length of 40 octets : * * NET_TCP_HDR_OPT_SIZE_MAX = NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN * * = 60 - 20 * * = 40 * * (4) 'NET_TCP_OPT_SIZE' MUST be pre-defined PRIOR to all definitions that require TCP option * size data type. ********************************************************************************************************* */ /*$PAGE*/ #define NET_TCP_HDR_OPT_END_LIST 0u #define NET_TCP_HDR_OPT_NOP 1u #define NET_TCP_HDR_OPT_MAX_SEG_SIZE 2u #define NET_TCP_HDR_OPT_WIN_SCALE 3u #define NET_TCP_HDR_OPT_SACK_PERMIT 4u #define NET_TCP_HDR_OPT_SACK 5u #define NET_TCP_HDR_OPT_ECHO_REQ 6u #define NET_TCP_HDR_OPT_ECHO_REPLY 7u #define NET_TCP_HDR_OPT_TS 8u #define NET_TCP_HDR_OPT_PAD NET_TCP_HDR_OPT_END_LIST #define NET_TCP_HDR_OPT_LEN_END_LIST 1u #define NET_TCP_HDR_OPT_LEN_NOP 1u #define NET_TCP_HDR_OPT_LEN_MAX_SEG_SIZE 4u #define NET_TCP_HDR_OPT_LEN_WIN_SCALE 3u #define NET_TCP_HDR_OPT_LEN_SACK_PERMIT 2u #define NET_TCP_HDR_OPT_LEN_ECHO_REQ 6u #define NET_TCP_HDR_OPT_LEN_ECHO_REPLY 6u #define NET_TCP_HDR_OPT_LEN_TS 10u #define NET_TCP_HDR_OPT_LEN_SACK_MIN 6u #define NET_TCP_HDR_OPT_LEN_SACK_MAX 38u #define NET_TCP_HDR_OPT_LEN_MIN 1u #define NET_TCP_HDR_OPT_LEN_MIN_LEN 2u #define NET_TCP_HDR_OPT_LEN_MAX 38u typedef CPU_INT32U NET_TCP_OPT_SIZE; /* TCP opt size data type (see Note #4). */ #define NET_TCP_HDR_OPT_SIZE_WORD (sizeof(NET_TCP_OPT_SIZE)) #define NET_TCP_HDR_OPT_SIZE_MAX (NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_OPT_NBR_MIN 0u #define NET_TCP_HDR_OPT_NBR_MAX (NET_TCP_HDR_OPT_SIZE_MAX / NET_TCP_HDR_OPT_SIZE_WORD) #define NET_TCP_HDR_OPT_IX NET_TCP_HDR_SIZE_MIN /*$PAGE*/ /* ********************************************************************************************************* * TCP OPTION CONFIGURATION TYPE DEFINES * * Note(s) : (1) NET_TCP_OPT_CFG_TYPE_&&& #define values specifically chosen as ASCII representations of * the TCP option configuration types. Memory displays of TCP option configuration buffers * will display the TCP option configuration TYPEs with their chosen ASCII names. ********************************************************************************************************* */ /* ---------------- TCP OPT CFG TYPES ----------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_OPT_CFG_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x2053534Du /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x204E4957u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x504B4353u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x4B434153u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x51455245u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4F484345u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x20205354u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x534D2053u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x4957204Eu /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x4353504Bu /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x41534B43u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x52455145u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x43454F48u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x53542020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #endif #endif /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION TIMEOUT DEFINES * * Note(s) : (1) (a) (1) RFC #1122, Section 4.2.2.13 'DISCUSSION' states that "the graceful close algorithm * of TCP requires that the connection state remain defined on (at least) one end of * the connection, for a timeout period of 2xMSL ... During this period, the (remote * socket, local socket) pair that defines the connection is busy and cannot be reused". * * (2) The following sections reiterate that the TIME-WAIT state timeout scalar is two * maximum segment lifetimes (2 MSL) : * * (A) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check Sequence Number : TIME-WAIT STATE' * (B) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check FIN Bit : TIME-WAIT STATE' * * (b) (1) RFC #793, Section 3.3 'Sequence Numbers : Knowing When to Keep Quiet' states that * "the Maximum Segment Lifetime (MSL) is ... to be 2 minutes. This is an engineering * choice, and may be changed if experience indicates it is desirable to do so". * * (2) Microsoft Corporation's Windows XP defaults MSL to 15 seconds. ********************************************************************************************************* */ /* Max seg timeout (see Note #1b) : */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MIN_SEC ( 0u ) /* ... min = 0 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MAX_SEC ( 2u * DEF_TIME_NBR_SEC_PER_MIN) /* ... max = 2 minutes */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_DFLT_SEC ( 15u ) /* ... dflt = 15 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_SCALAR 2u /* ... scalar (see Note #1a). */ #define NET_TCP_CONN_TIMEOUT_CONN_DFLT_SEC (120u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt conn timeout = 120 minutes */ #define NET_TCP_CONN_TIMEOUT_USER_DFLT_SEC ( 30u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt user timeout = 30 minutes */ /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION STATES * * Note(s) : (1) See the following RFC's for TCP state machine summary : * * (a) RFC # 793; Sections 3.2, 3.4, 3.5, 3.9 * (b) RFC #1122; Sections 4.2.2.8, 4.2.2.10, 4.2.2.11, 4.2.2.13, 4.2.2.18, 4.2.2.20 * * (2) (a) #### Additional closing-data-available state used for closing connections to allow the * application layer to receive any remaining data. * * See also 'net_tcp.c NetTCP_RxPktConnHandlerFinWait1() Note #2f5A2', * 'net_tcp.c NetTCP_RxPktConnHandlerFinWait2() Note #2f5B', * 'net_tcp.c NetTCP_RxPktConnHandlerClosing() Note #2d2B2a1B', * & 'net_tcp.c NetTCP_RxPktConnHandlerLastAck() Note #2d2A1b'. ********************************************************************************************************* */ #define NET_TCP_CONN_STATE_NONE 0u #define NET_TCP_CONN_STATE_FREE 1u #define NET_TCP_CONN_STATE_CLOSED 10u #define NET_TCP_CONN_STATE_LISTEN 20u #define NET_TCP_CONN_STATE_SYNC_RXD 30u #define NET_TCP_CONN_STATE_SYNC_RXD_PASSIVE 31u #define NET_TCP_CONN_STATE_SYNC_RXD_ACTIVE 32u #define NET_TCP_CONN_STATE_SYNC_TXD 35u #define NET_TCP_CONN_STATE_CONN 40u #define NET_TCP_CONN_STATE_FIN_WAIT_1 50u #define NET_TCP_CONN_STATE_FIN_WAIT_2 51u #define NET_TCP_CONN_STATE_CLOSING 52u #define NET_TCP_CONN_STATE_TIME_WAIT 53u #define NET_TCP_CONN_STATE_CLOSE_WAIT 55u #define NET_TCP_CONN_STATE_LAST_ACK 56u #define NET_TCP_CONN_STATE_CLOSING_DATA_AVAIL 59u /* See Note #2a. */ /* ********************************************************************************************************* * TCP CONNECTION QUEUE STATES ********************************************************************************************************* */ #define NET_TCP_RX_Q_STATE_NONE 0u #define NET_TCP_RX_Q_STATE_CLOSED 100u #define NET_TCP_RX_Q_STATE_CLOSING 101u #define NET_TCP_RX_Q_STATE_SYNC 110u #define NET_TCP_RX_Q_STATE_CONN 111u #define NET_TCP_TX_Q_STATE_NONE 0u #define NET_TCP_TX_Q_STATE_CLOSED 200u #define NET_TCP_TX_Q_STATE_CLOSING 201u #define NET_TCP_TX_Q_STATE_SYNC 210u #define NET_TCP_TX_Q_STATE_CONN 211u #define NET_TCP_TX_Q_STATE_SUSPEND 215u #define NET_TCP_TX_Q_STATE_CLOSED_SUSPEND 220u #define NET_TCP_TX_Q_STATE_CLOSING_SUSPEND 221u /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION CODE DEFINES **************
上傳時間： 2015-11-22
上傳用戶：the same kong
/* * _168ZHONGDUAN2.c * * Created: 2014/11/2 15:12:45 * Author: lenovo */ #include <avr/io.h> #include <avr/iom168pa.h> #include <avr/interrupt.h> #include <util/delay.h> #include <avr/eeprom.h> //#include <util/delay_basic.h> //unsigned char const SEGtable[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x40}; #define BIT(x) (1<<(x)) #include<avr/signal.h> #include<avr/pgmspace.h> #include<util/delay.h> #include<avr/eeprom.h> #define setb(val,bitn) (val|=(1<<(bitn)))//設置某IO口某位為1 #define clr(val,bitn) (val&=~(1<<(bitn)))//設置某IO口某位為0 #define get(val,bitn) (val&(1<<(bitn)))//讀取某位狀態 //uchar ACT[8] ={0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f}; #define CPL_BIT(x,y) (x^=(1<<y)) #define CLR_BIT(x,y) (x&=~(1<<y)) #define SET_1(a,b) a|=(1<<b) #define CLE_0(a,b) a&=~(1<<b) /*------宏定義------*/ #include <avr/wdt.h> #include <avr/sleep.h> #include <avr/interrupt.h> #include <avr/pgmspace.h> #include <util/delay.h> #include <avr/eeprom.h> #define setb(val,bitn) (val|=(1<<(bitn)))//設置某IO口某位為1 #define clr(val,bitn) (val&=~(1<<(bitn)))//設置某IO口某位為0 #define get(val,bitn) (val&(1<<(bitn)))//讀取某位狀態 #define uint8 unsigned char #define uint16 unsigned int #define P_LCDCS1 setb(PORTB,5) #define P_LCDCS0 clr(PORTB,5) #define P_LCDRST1 setb(PORTB,1) #define P_LCDRST0 clr(PORTB,1) #define P_LCDRS1 setb(PORTB,2) #define P_LCDRS0 clr(PORTB,2) #define P_LCDDAT1 setb(PORTB,4) #define P_LCDDAT0 clr(PORTB,4) #define P_LCDCLK1 setb(PORTB,3) #define P_LCDCLK0 clr(PORTB,3) //#define LCD_ //-----頁地址定義----- #define Page1 0 #define Page2 1 #define Page3 2 #define Page4 3 #define Page5 4 #define Page6 5 #define Page7 6 #define Page8 7 //-----列地址定義-----每8列地址增1 #define List8_1 0 #define List8_2 7 #define List8_3 15 #define List8_4 23 #define List8_5 31 #define List8_6 39 #define List8_7 47 #define List8_8 55 #define List8_9 63 #define List8_10 71 #define List8_11 79 #define List8_12 87 #define List8_13 95 #define List8_14 103 #define List8_15 111 #define List8_16 119 //#define List8_17 127 //-----列地址定義-----每16列地址增1 #define List16_1 0 #define List16_2 15 #define List16_3 31 #define List16_4 47 #define List16_5 63 #define List16_6 79 #define List16_7 95 #define List16_8 111 //---------------------------------- #define STR_CHARG "Charge" //提示充電 #define STR_PRCE "%" //電量百分比 #define STR_ERR "Err" //出錯顯示 #define STR_OFF "OFF" //關機顯示 //待機顯示 #define STR_WAIT1 "Portable UPS" #define STR_WAIT2 "110V/60HZ" #define STR_WAIT3 "Select:DC OR AC" #define STR_WAIT4 "BATTERY:" //開機顯示 #define STR_OUTSTATUS "Out Status:" #define STR_DCOUT12V "DC12V" #define STR_DCOUT5V "DC5V" #define STR_ACOUT "AC110V" //#define STR_MAOHAO ":" //====================================== extern uint8 LOCKA[2][16] ; //extern uint8 code BATS[10][16] ; extern uint8 BAT2S[12][32] ; extern uint8 NC[] ; extern uint8 mao_hao[] ; extern uint8 num1[] ; extern uint8 num2[] ; extern uint8 num3[] ; extern uint8 num4[] ; extern uint8 num5[] ; extern uint8 num6[] ; extern uint8 num7[] ; extern uint8 num8[] ; extern uint8 num9[] ; extern uint8 Tab_Ascii_8x16[95][16] ; extern uint8 Tab_Ascii_5x7[95][5] ; extern uint8 zhuang1[] ; extern uint8 tai1[] ; extern uint8 shi1[] ; extern uint8 yong1[] ; //---------------------------------- //extern void LcdWriteCommand(uint8 data1) ; extern void Display_Graphic_32x32(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_32x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_16x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_Graphic_8x16(uint8 page,uint8 column,uint8 *dp) ; extern void Display_String_8x16(uint8 page,uint8 column,uint8 *text) ; extern void Display_Num_8x16(uint8 page,uint8 column,uint8 Num) ; extern void Display_Digital_8x16(uint8 page,uint8 column,uint8 *a) ; extern void Display_Nop_8x16(uint8 page,uint8 column,uint8 DatLong) ; extern void Display_String_5x7(uint8 page,uint8 column,uint8 *text) ; extern void Full_Display(void) ; extern void Clear_Screen(void) ; extern void Init_lcd12864(void) ; //#endif //========c12864.c============================================== /*************************************************** LCD:晶聯訊電子 JLX12864G-086-PN(不帶字庫IC-UC1701X) 僅支持串行驅動方式 ***************************************************/ //#include "global.h" //#include "c12864.h" #define Tab_Ascii_8x16_CALL1 //粗體字形 #define Tab_Ascii_8x16_CALL2 //細體字形 #define Tab_Ascii_5x7_CALL #define Display_Graphic_32x32_CALL #define Display_Graphic_32x16_CALL #define Display_Graphic_16x16_CALL #define Display_Graphic_8x16_CALL #define Display_String_8x16_CALL //顯示字符串 #define Display_Num_8x16_CALL //顯示單個數據0-9 #define Display_Digital_8x16_CALL //顯示數據0-9999 #define Display_Nop_8x16_CALL //填充8*16的空字符N個 #define Display_String_5x7_CALL #define Full_Display_CALL //============================================================================== uint8 aa[]={0,1,2,3,4,5,6,7,8,9}; uint8 LOCKA[2][16]={ //-- 童鎖符號 -- //-- 此字體下對應的點陣為：寬x高=16x16 -- //0x00, 0x00, 0xc0, 0xe0, 0xf0, 0xd8, 0xcc, 0xc4, 0xc4, 0xcc, 0xd8, 0xf0, 0xe0, 0xc0, 0x00, 0x00, //0x00, 0x00, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x00, 0x00, 0x00, 0x00, 0xc0, 0xe0, 0xb0, 0x98, 0x8c, 0x8c, 0x8c, 0x8c, 0x98, 0xb0, 0xe0, 0xc0, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x3f, 0x00, 0x00, } ; const PROGMEM uint8_t BATS[10][16]={ //-- 電池符號 -- //-- 此字體下對應的點陣為：寬x高=16x16 -- 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x40, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x70, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x0c, 0x0e, 0x0e, 0x0c, 0x08, 0x08, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7e, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0xc8, 0xc8, 0xcc, 0xce, 0xce, 0xcc, 0xc8, 0xc8, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0xf8, 0xf8, 0xfc, 0xfe, 0xfe, 0xfc, 0xf8, 0xf8, 0xf8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x7f, 0x00, 0x00, 0x00, }; const PROGMEM uint8_t BAT2S1[12][32]={ /*-- 電池符號 --*/ /*-- 此字體下對應的點陣為：寬x高=32x16 --*/ {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0x08, 0x08, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x3f, 0x07, 0x03}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xf8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xe8, 0xe8, 0x08, 0x08, 0xf8, 0xc0, 0x80}, {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x2f, 0x2f, 0x20, 0x20, 0x3f, 0x07, 0x03}, } ; const PROGMEM uint8_t BAT2S2[2][32]={ //-- 電池符號 不顯示 -- //-- 此字體下對應的點陣為：寬x高=32x16 -- 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, } ; uint8 NC[]={ /*-- 文字: 空符號 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, } ; uint8 mao_hao[]={ /*-- 文字: : (冒號） --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00}; uint8 num0[]={ /*-- 文字: 0 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00 }; uint8 num1[]={ /*-- 文字: 1 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00 }; uint8 num2[]={ /*-- 文字: 2 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00 //細體 //0x08,0x0C,0x84,0xC4,0x64,0x3C,0x18,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0C,0x00, // 粗體 }; uint8 num3[]={ /*-- 文字: 3 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00 }; uint8 num4[]={ /*-- 文字: 4 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00 }; uint8 num5[]={ /*-- 文字: 5 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00 }; uint8 num6[]={ /*-- 文字: 6 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00 }; uint8 num7[]={ /*-- 文字: 7 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00 }; uint8 num8[]={ /*-- 文字: 8 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00 }; uint8 num9[]={ /*-- 文字: 9 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00 }; //=======8x16======================================================================= #ifdef Display_String_8x16_CALL //Tab_Ascii_8x16_CALL const PROGMEM uint8_t Tab_Ascii_8x161[95][16]={ //粗體字形 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // - - 0x00,0x00,0x38,0xFC,0xFC,0x38,0x00,0x00,0x00,0x00,0x00,0x0D,0x0D,0x00,0x00,0x00, // -!- 0x00,0x0E,0x1E,0x00,0x00,0x1E,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -"- 0x20,0xF8,0xF8,0x20,0xF8,0xF8,0x20,0x00,0x02,0x0F,0x0F,0x02,0x0F,0x0F,0x02,0x00, // -#- 0x38,0x7C,0x44,0x47,0x47,0xCC,0x98,0x00,0x03,0x06,0x04,0x1C,0x1C,0x07,0x03,0x00, // -$- 0x30,0x30,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x0C,0x0C,0x00, // -%- 0x80,0xD8,0x7C,0xE4,0xBC,0xD8,0x40,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -&- 0x00,0x10,0x1E,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -'- 0x00,0x00,0xF0,0xF8,0x0C,0x04,0x00,0x00,0x00,0x00,0x03,0x07,0x0C,0x08,0x00,0x00, // -(- 0x00,0x00,0x04,0x0C,0xF8,0xF0,0x00,0x00,0x00,0x00,0x08,0x0C,0x07,0x03,0x00,0x00, // -)- 0x80,0xA0,0xE0,0xC0,0xC0,0xE0,0xA0,0x80,0x00,0x02,0x03,0x01,0x01,0x03,0x02,0x00, // -*- 0x00,0x80,0x80,0xE0,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x03,0x03,0x00,0x00,0x00, // -+- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x1E,0x0E,0x00,0x00,0x00, // -,- 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // --- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x00, // -.- 0x00,0x00,0x00,0x80,0xC0,0x60,0x30,0x00,0x0C,0x06,0x03,0x01,0x00,0x00,0x00,0x00, // -/- 0xF8,0xFC,0x04,0xC4,0x24,0xFC,0xF8,0x00,0x07,0x0F,0x09,0x08,0x08,0x0F,0x07,0x00, // -0- 0x00,0x10,0x18,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x08,0x08,0x00, // -1- 0x08,0x0C,0x84,0xC4,0x64,0x3C,0x18,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0C,0x00, // -2- 0x08,0x0C,0x44,0x44,0x44,0xFC,0xB8,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -3- 0xC0,0xE0,0xB0,0x98,0xFC,0xFC,0x80,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00, // -4- 0x7C,0x7C,0x44,0x44,0xC4,0xC4,0x84,0x00,0x04,0x0C,0x08,0x08,0x08,0x0F,0x07,0x00, // -5- 0xF0,0xF8,0x4C,0x44,0x44,0xC0,0x80,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -6- 0x0C,0x0C,0x04,0x84,0xC4,0x7C,0x3C,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00,0x00, // -7- 0xB8,0xFC,0x44,0x44,0x44,0xFC,0xB8,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -8- 0x38,0x7C,0x44,0x44,0x44,0xFC,0xF8,0x00,0x00,0x08,0x08,0x08,0x0C,0x07,0x03,0x00, // -9- 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,0x00, // -:- 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,0x08,0x0E,0x06,0x00,0x00,0x00, // -;- 0x00,0x80,0xC0,0x60,0x30,0x18,0x08,0x00,0x00,0x00,0x01,0x03,0x06,0x0C,0x08,0x00, // -<- 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x00, // -=- 0x00,0x08,0x18,0x30,0x60,0xC0,0x80,0x00,0x00,0x08,0x0C,0x06,0x03,0x01,0x00,0x00, // ->- 0x18,0x1C,0x04,0xC4,0xE4,0x3C,0x18,0x00,0x00,0x00,0x00,0x0D,0x0D,0x00,0x00,0x00, // -?- 0xF0,0xF8,0x08,0xC8,0xC8,0xF8,0xF0,0x00,0x07,0x0F,0x08,0x0B,0x0B,0x0B,0x01,0x00, // -@- 0xE0,0xF0,0x98,0x8C,0x98,0xF0,0xE0,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -A- 0x04,0xFC,0xFC,0x44,0x44,0xFC,0xB8,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0F,0x07,0x00, // -B- 0xF0,0xF8,0x0C,0x04,0x04,0x0C,0x18,0x00,0x03,0x07,0x0C,0x08,0x08,0x0C,0x06,0x00, // -C- 0x04,0xFC,0xFC,0x04,0x0C,0xF8,0xF0,0x00,0x08,0x0F,0x0F,0x08,0x0C,0x07,0x03,0x00, // -D- 0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -E- 0x04,0xFC,0xFC,0x44,0xE4,0x0C,0x1C,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -F- 0xF0,0xF8,0x0C,0x84,0x84,0x8C,0x98,0x00,0x03,0x07,0x0C,0x08,0x08,0x07,0x0F,0x00, // -G- 0xFC,0xFC,0x40,0x40,0x40,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -H- 0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -I- 0x00,0x00,0x00,0x04,0xFC,0xFC,0x04,0x00,0x07,0x0F,0x08,0x08,0x0F,0x07,0x00,0x00, // -J- 0x04,0xFC,0xFC,0xC0,0xF0,0x3C,0x0C,0x00,0x08,0x0F,0x0F,0x00,0x01,0x0F,0x0E,0x00, // -K- 0x04,0xFC,0xFC,0x04,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x08,0x0C,0x0E,0x00, // -L- 0xFC,0xFC,0x38,0x70,0x38,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -M- 0xFC,0xFC,0x38,0x70,0xE0,0xFC,0xFC,0x00,0x0F,0x0F,0x00,0x00,0x00,0x0F,0x0F,0x00, // -N- 0xF0,0xF8,0x0C,0x04,0x0C,0xF8,0xF0,0x00,0x03,0x07,0x0C,0x08,0x0C,0x07,0x03,0x00, // -O- 0x04,0xFC,0xFC,0x44,0x44,0x7C,0x38,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -P- 0xF8,0xFC,0x04,0x04,0x04,0xFC,0xF8,0x00,0x07,0x0F,0x08,0x0E,0x3C,0x3F,0x27,0x00, // -Q- 0x04,0xFC,0xFC,0x44,0xC4,0xFC,0x38,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -R- 0x18,0x3C,0x64,0x44,0xC4,0x9C,0x18,0x00,0x06,0x0E,0x08,0x08,0x08,0x0F,0x07,0x00, // -S- 0x00,0x1C,0x0C,0xFC,0xFC,0x0C,0x1C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -T- 0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -U- 0xFC,0xFC,0x00,0x00,0x00,0xFC,0xFC,0x00,0x01,0x03,0x06,0x0C,0x06,0x03,0x01,0x00, // -V- 0xFC,0xFC,0x00,0x80,0x00,0xFC,0xFC,0x00,0x03,0x0F,0x0E,0x03,0x0E,0x0F,0x03,0x00, // -W- 0x0C,0x3C,0xF0,0xC0,0xF0,0x3C,0x0C,0x00,0x0C,0x0F,0x03,0x00,0x03,0x0F,0x0C,0x00, // -X- 0x00,0x3C,0x7C,0xC0,0xC0,0x7C,0x3C,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -Y- 0x1C,0x0C,0x84,0xC4,0x64,0x3C,0x1C,0x00,0x0E,0x0F,0x09,0x08,0x08,0x0C,0x0E,0x00, // -Z- 0x00,0x00,0xFC,0xFC,0x04,0x04,0x00,0x00,0x00,0x00,0x0F,0x0F,0x08,0x08,0x00,0x00, // -[- 0x38,0x70,0xE0,0xC0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x07,0x0E,0x00, // -\- 0x00,0x00,0x04,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x08,0x08,0x0F,0x0F,0x00,0x00, // -]- 0x08,0x0C,0x06,0x03,0x06,0x0C,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -^- 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, // -_- 0x00,0x00,0x03,0x07,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -`- 0x00,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -a- 0x04,0xFC,0xFC,0x20,0x60,0xC0,0x80,0x00,0x08,0x0F,0x07,0x08,0x08,0x0F,0x07,0x00, // -b- 0xC0,0xE0,0x20,0x20,0x20,0x60,0x40,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -c- 0x80,0xC0,0x60,0x24,0xFC,0xFC,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -d- 0xC0,0xE0,0xA0,0xA0,0xA0,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0C,0x04,0x00, // -e- 0x40,0xF8,0xFC,0x44,0x0C,0x18,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -f- 0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x27,0x6F,0x48,0x48,0x7F,0x3F,0x00,0x00, // -g- 0x04,0xFC,0xFC,0x40,0x20,0xE0,0xC0,0x00,0x08,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -h- 0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -i- 0x00,0x00,0x00,0x00,0x20,0xEC,0xEC,0x00,0x00,0x30,0x70,0x40,0x40,0x7F,0x3F,0x00, // -j- 0x04,0xFC,0xFC,0x80,0xC0,0x60,0x20,0x00,0x08,0x0F,0x0F,0x01,0x03,0x0E,0x0C,0x00, // -k- 0x00,0x00,0x04,0xFC,0xFC,0x00,0x00,0x00,0x00,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00, // -l- 0xE0,0xE0,0x60,0xC0,0x60,0xE0,0xC0,0x00,0x0F,0x0F,0x00,0x0F,0x00,0x0F,0x0F,0x00, // -m- 0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x00,0x0F,0x0F,0x00,0x00,0x0F,0x0F,0x00, // -n- 0xC0,0xE0,0x20,0x20,0x20,0xE0,0xC0,0x00,0x07,0x0F,0x08,0x08,0x08,0x0F,0x07,0x00, // -o- 0x20,0xE0,0xC0,0x20,0x20,0xE0,0xC0,0x00,0x40,0x7F,0x7F,0x48,0x08,0x0F,0x07,0x00, // -p- 0xC0,0xE0,0x20,0x20,0xC0,0xE0,0x20,0x00,0x07,0x0F,0x08,0x48,0x7F,0x7F,0x40,0x00, // -q- 0x20,0xE0,0xC0,0x60,0x20,0x60,0xC0,0x00,0x08,0x0F,0x0F,0x08,0x00,0x00,0x00,0x00, // -r- 0x40,0xE0,0xA0,0x20,0x20,0x60,0x40,0x00,0x04,0x0C,0x09,0x09,0x0B,0x0E,0x04,0x00, // -s- 0x20,0x20,0xF8,0xFC,0x20,0x20,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x0C,0x04,0x00, // -t- 0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x07,0x0F,0x08,0x08,0x07,0x0F,0x08,0x00, // -u- 0x00,0xE0,0xE0,0x00,0x00,0xE0,0xE0,0x00,0x00,0x03,0x07,0x0C,0x0C,0x07,0x03,0x00, // -v- 0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x07,0x0F,0x0C,0x07,0x0C,0x0F,0x07,0x00, // -w- 0x20,0x60,0xC0,0x80,0xC0,0x60,0x20,0x00,0x08,0x0C,0x07,0x03,0x07,0x0C,0x08,0x00, // -x- 0xE0,0xE0,0x00,0x00,0x00,0xE0,0xE0,0x00,0x47,0x4F,0x48,0x48,0x68,0x3F,0x1F,0x00, // -y- 0x60,0x60,0x20,0xA0,0xE0,0x60,0x20,0x00,0x0C,0x0E,0x0B,0x09,0x08,0x0C,0x0C,0x00, // -z- 0x00,0x40,0x40,0xF8,0xBC,0x04,0x04,0x00,0x00,0x00,0x00,0x07,0x0F,0x08,0x08,0x00, // -{- 0x00,0x00,0x00,0xBC,0xBC,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x0F,0x00,0x00,0x00, // -|- 0x00,0x04,0x04,0xBC,0xF8,0x40,0x40,0x00,0x00,0x08,0x08,0x0F,0x07,0x00,0x00,0x00, // -}- 0x08,0x0C,0x04,0x0C,0x08,0x0C,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // -~- } ; #endif //Tab_Ascii_8x16_CALL1 //=======8x16======================================================================= //#ifdef Tab_Ascii_8x16_CALL2 // #ifdef Display_Num_8x16_CALL const PROGMEM uint8_t Tab_Ascii_8x162[95][16]={ //細體字形 /*-- 文字: --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: ! --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00, /*-- 文字: " --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: # --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00, /*-- 文字: $ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00, /*-- 文字: % --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00, /*-- 文字: & --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10, /*-- 文字: ' --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: ( --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00, /*-- 文字: ) --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00, /*-- 文字: * --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00, /*-- 文字: + --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00, /*-- 文字: , --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00, /*-- 文字: - --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01, /*-- 文字: . --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00, /*-- 文字: / --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00, /*-- 文字: 0 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: 1 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: 2 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00, /*-- 文字: 3 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 4 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00, /*-- 文字: 5 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 6 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: 7 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00, /*-- 文字: 8 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00, /*-- 文字: 9 --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00, /*-- 文字: : --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00, /*-- 文字: ; --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00, /*-- 文字: < --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00, /*-- 文字: = --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00, /*-- 文字: > --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00, /*-- 文字: ? --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00, /*-- 文字: @ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00, /*-- 文字: A --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20, /*-- 文字: B --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: C --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00, /*-- 文字: D --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: E --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00, /*-- 文字: F --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00, /*-- 文字: G --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00, /*-- 文字: H --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20, /*-- 文字: I --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: J --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00, /*-- 文字: K --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00, /*-- 文字: L --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00, /*-- 文字: M --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00, /*-- 文字: N --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00, /*-- 文字: O --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00, /*-- 文字: P --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00, /*-- 文字: Q --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00, /*-- 文字: R --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20, /*-- 文字: S --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00, /*-- 文字: T --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00, /*-- 文字: U --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00, /*-- 文字: V --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00, /*-- 文字: W --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00, /*-- 文字: X --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20, /*-- 文字: Y --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00, /*-- 文字: Z --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00, /*-- 文字: [ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00, /*-- 文字: \ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00, /*-- 文字: ] --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00, /*-- 文字: ^ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: _ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80, /*-- 文字: ` --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, /*-- 文字: a --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20, /*-- 文字: b --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: c --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00, /*-- 文字: d --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20, /*-- 文字: e --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00, /*-- 文字: f --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: g --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00, /*-- 文字: h --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20, /*-- 文字: i --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: j --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00, /*-- 文字: k --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00, /*-- 文字: l --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00, /*-- 文字: m --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F, /*-- 文字: n --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20, /*-- 文字: o --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00, /*-- 文字: p --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00, /*-- 文字: q --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80, /*-- 文字: r --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00, /*-- 文字: s --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00, /*-- 文字: t --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00, /*-- 文字: u --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20, /*-- 文字: v --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00, /*-- 文字: w --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00, /*-- 文字: x --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00, /*-- 文字: y --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00, /*-- 文字: z --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00, /*-- 文字: { --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40, /*-- 文字: | --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00, /*-- 文字: } --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00, /*-- 文字: ~ --*/ /*-- Comic Sans MS12; 此字體下對應的點陣為：寬x高=8x16 --*/ 0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }; ///#endif //#endif //Tab_Ascii_8x16_CALL1 //=======5x7======================================================================= //#ifdef Tab_Ascii_5x7_CALL const PROGMEM uint8_t Tab_Ascii_5x71[95][5]={ /*全體ASCII 列表:5x7點陣*/ 0x00,0x00,0x00,0x00,0x00,//space 0x00,0x00,0x4f,0x00,0x00,//! 0x00,0x07,0x00,0x07,0x00,//" 0x14,0x7f,0x14,0x7f,0x14,//# 0x24,0x2a,0x7f,0x2a,0x12,//$ 0x23,0x13,0x08,0x64,0x62,//% 0x36,0x49,0x55,0x22,0x50,//& 0x00,0x05,0x07,0x00,0x00,//] 0x00,0x1c,0x22,0x41,0x00,//( 0x00,0x41,0x22,0x1c,0x00,//) 0x14,0x08,0x3e,0x08,0x14,//* 0x08,0x08,0x3e,0x08,0x08,//+ 0x00,0x50,0x30,0x00,0x00,//, 0x08,0x08,0x08,0x08,0x08,//- 0x00,0x60,0x60,0x00,0x00,//. 0x20,0x10,0x08,0x04,0x02,/// 0x3e,0x51,0x49,0x45,0x3e,//0 0x00,0x42,0x7f,0x40,0x00,//1 0x42,0x61,0x51,0x49,0x46,//2 0x21,0x41,0x45,0x4b,0x31,//3 0x18,0x14,0x12,0x7f,0x10,//4 0x27,0x45,0x45,0x45,0x39,//5 0x3c,0x4a,0x49,0x49,0x30,//6 0x01,0x71,0x09,0x05,0x03,//7 0x36,0x49,0x49,0x49,0x36,//8 0x06,0x49,0x49,0x29,0x1e,//9 0x00,0x36,0x36,0x00,0x00,//: 0x00,0x56,0x36,0x00,0x00,//; 0x08,0x14,0x22,0x41,0x00,//< 0x14,0x14,0x14,0x14,0x14,//= 0x00,0x41,0x22,0x14,0x08,//> 0x02,0x01,0x51,0x09,0x06,//? 0x32,0x49,0x79,0x41,0x3e,//@ 0x7e,0x11,0x11,0x11,0x7e,//A 0x7f,0x49,0x49,0x49,0x36,//B 0x3e,0x41,0x41,0x41,0x22,//C 0x7f,0x41,0x41,0x22,0x1c,//D 0x7f,0x49,0x49,0x49,0x41,//E 0x7f,0x09,0x09,0x09,0x01,//F 0x3e,0x41,0x49,0x49,0x7a,//G 0x7f,0x08,0x08,0x08,0x7f,//H 0x00,0x41,0x7f,0x41,0x00,//I 0x20,0x40,0x41,0x3f,0x01,//J 0x7f,0x08,0x14,0x22,0x41,//K 0x7f,0x40,0x40,0x40,0x40,//L 0x7f,0x02,0x0c,0x02,0x7f,//M 0x7f,0x04,0x08,0x10,0x7f,//N 0x3e,0x41,0x41,0x41,0x3e,//O 0x7f,0x09,0x09,0x09,0x06,//P 0x3e,0x41,0x51,0x21,0x5e,//Q 0x7f,0x09,0x19,0x29,0x46,//R 0x46,0x49,0x49,0x49,0x31,//S 0x01,0x01,0x7f,0x01,0x01,//T 0x3f,0x40,0x40,0x40,0x3f,//U 0x1f,0x20,0x40,0x20,0x1f,//V 0x3f,0x40,0x38,0x40,0x3f,//W 0x63,0x14,0x08,0x14,0x63,//X 0x07,0x08,0x70,0x08,0x07,//Y 0x61,0x51,0x49,0x45,0x43,//Z 0x00,0x7f,0x41,0x41,0x00,//[ 0x02,0x04,0x08,0x10,0x20,//\ 0x00,0x41,0x41,0x7f,0x00,//] 0x04,0x02,0x01,0x02,0x04,//^ 0x40,0x40,0x40,0x40,0x40,//_ 0x01,0x02,0x04,0x00,0x00,//` 0x20,0x54,0x54,0x54,0x78,//a 0x7f,0x48,0x48,0x48,0x30,//b 0x38,0x44,0x44,0x44,0x44,//c 0x30,0x48,0x48,0x48,0x7f,//d 0x38,0x54,0x54,0x54,0x58,//e 0x00,0x08,0x7e,0x09,0x02,//f 0x48,0x54,0x54,0x54,0x3c,//g 0x7f,0x08,0x08,0x08,0x70,//h 0x00,0x00,0x7a,0x00,0x00,//i 0x20,0x40,0x40,0x3d,0x00,//j 0x7f,0x20,0x28,0x44,0x00,//k 0x00,0x41,0x7f,0x40,0x00,//l 0x7c,0x04,0x38,0x04,0x7c,//m 0x7c,0x08,0x04,0x04,0x78,//n 0x38,0x44,0x44,0x44,0x38,//o 0x7c,0x14,0x14,0x14,0x08,//p 0x08,0x14,0x14,0x14,0x7c,//q 0x7c,0x08,0x04,0x04,0x08,//r 0x48,0x54,0x54,0x54,0x24,//s 0x04,0x04,0x3f,0x44,0x24,//t 0x3c,0x40,0x40,0x40,0x3c,//u 0x1c,0x20,0x40,0x20,0x1c,//v 0x3c,0x40,0x30,0x40,0x3c,//w 0x44,0x28,0x10,0x28,0x44,//x 0x04,0x48,0x30,0x08,0x04,//y 0x44,0x64,0x54,0x4c,0x44,//z 0x08,0x36,0x41,0x41,0x00,//{ 0x00,0x00,0x77,0x00,0x00,//| 0x00,0x41,0x41,0x36,0x08,//} 0x04,0x02,0x02,0x02,0x01,//~ }; //#endif //Tab_Ascii_5x7_CALL uint8 zhuang1[]={ /*-- 文字: 狀 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/ 0x08,0x30,0x00,0xFF,0x20,0x20,0x20,0x20,0xFF,0x20,0xE1,0x26,0x2C,0x20,0x20,0x00, 0x04,0x02,0x01,0xFF,0x40,0x20,0x18,0x07,0x00,0x00,0x03,0x0C,0x30,0x60,0x20,0x00 }; uint8 tai1[]={ /*-- 文字: 態 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/ 0x00,0x04,0x04,0x04,0x84,0x44,0x34,0x4F,0x94,0x24,0x44,0x84,0x84,0x04,0x00,0x00, 0x00,0x60,0x39,0x01,0x00,0x3C,0x40,0x42,0x4C,0x40,0x40,0x70,0x04,0x09,0x31,0x00 }; uint8 shi1[]={ /*-- 文字: 使 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/ 0x40,0x20,0xF0,0x1C,0x07,0xF2,0x94,0x94,0x94,0xFF,0x94,0x94,0x94,0xF4,0x04,0x00, 0x00,0x00,0x7F,0x00,0x40,0x41,0x22,0x14,0x0C,0x13,0x10,0x30,0x20,0x61,0x20,0x00 }; uint8 yong1[]={ /*-- 文字: 用 --*/ /*-- 宋體12; 此字體下對應的點陣為：寬x高=16x16 --*/ 0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0xFE,0x22,0x22,0x22,0x22,0xFE,0x00,0x00, 0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0xFF,0x02,0x02,0x42,0x82,0x7F,0x00,0x00 }; //x=9 y=16 點陣 0-9 const PROGMEM uint8_t lcd_numbers_lit[]={ 0x00,0xE0,0xE0,0x60,0x20,0x60,0xE0,0xE0,0x00,//0 0x00,0x7F,0x7F,0x60,0x40,0x60,0x7F,0x7F,0x00, 0x00,0x00,0x40,0x40,0xE0,0xE0,0x00,0x00,0x00,//1 0x00,0x00,0x00,0x00,0x7F,0x7F,0x00,0x00,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0xC0,0x00,//2 0x00,0x71,0x79,0x78,0x5E,0x47,0x43,0x41,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0xC0,0x00,//3 0x00,0x78,0x78,0x42,0x47,0x7F,0x7D,0x39,0x00, 0x00,0x00,0x00,0x80,0xE0,0xE0,0xE0,0x00,0x00,//4 0x00,0x0E,0x0F,0x0B,0x7F,0x7F,0x7F,0x08,0x00, 0x00,0xE0,0xE0,0xE0,0x20,0x20,0x20,0x20,0x00,//5 0x00,0x73,0x73,0x43,0x41,0x7F,0x7F,0x3E,0x00, 0x00,0xE0,0xE0,0x60,0x20,0x60,0x60,0x60,0x00,//6 0x00,0x7F,0x7F,0x43,0x43,0x7F,0x7E,0x3C,0x00, 0x00,0x20,0x20,0x20,0xA0,0xE0,0xE0,0x60,0x00,//7 0x00,0x00,0x40,0x78,0x7F,0x0F,0x01,0x00,0x00, 0x00,0xE0,0xE0,0x20,0x20,0x20,0xE0,0xE0,0x00,//8 0x00,0x7D,0x7D,0x47,0x42,0x47,0x7D,0x7D,0x00, 0x00,0xE0,0xE0,0x20,0x20,0xE0,0xE0,0x80,0x00,//9 0x00,0x67,0x6F,0x4C,0x6C,0x7F,0x3F,0x0F,0x00 }; //x=12 y=16 點陣 0-9數字 const PROGMEM uint8_t lcd_numbers[]={ 0x00,0xF0,0xFC,0xFC,0x0E,0x02,0x02,0x0E,0xFC,0xFC,0xF0,0x00,//0 0x00,0x07,0x3F,0x3F,0x70,0x40,0x40,0x70,0x3F,0x3F,0x07,0x00, 0x00,0x00,0x00,0x08,0x08,0xFC,0xFE,0xFE,0x00,0x00,0x00,0x00,//1 0x00,0x00,0x00,0x00,0x00,0x7F,0x7F,0x7F,0x00,0x00,0x00,0x00, 0x00,0x38,0x3C,0x3E,0x06,0x02,0x86,0xFE,0xFC,0x78,0x00,0x00,//2 0x00,0x60,0x78,0x7C,0x5E,0x4F,0x43,0x41,0x40,0x40,0x00,0x00, 0x00,0x18,0x1C,0x1E,0x86,0x82,0xC6,0xFE,0x7C,0x38,0x00,0x00,//3 0x00,0x1C,0x3C,0x7C,0x60,0x40,0x61,0x7F,0x3F,0x1E,0x00,0x00, 0x00,0x00,0x80,0xC0,0xF0,0x3C,0xFE,0xFE,0xFE,0x00,0x00,0x00,//4 0x00,0x06,0x07,0x05,0x04,0x04,0x7F,0x7F,0x7F,0x04,0x04,0x00, 0x00,0x00,0xFE,0xFE,0xFE,0x62,0x62,0xE2,0xE2,0x82,0x00,0x00,//5 0x00,0x18,0x38,0x78,0x60,0x40,0x60,0x7F,0x3F,0x1F,0x00,0x00, 0x00,0xF0,0xFC,0xFC,0xCE,0x42,0xC6,0xCE,0x8E,0x0C,0x00,0x00,//6 0x00,0x0F,0x3F,0x7F,0x60,0x40,0x60,0x7F,0x3F,0x1F,0x00,0x00, 0x00,0x02,0x02,0x02,0x02,0x82,0xF2,0xFE,0x7E,0x0E,0x00,0x00,//7 0x00,0x00,0x00,0x60,0x7C,0x7F,0x1F,0x03,0x00,0x00,0x00,0x00, 0x00,0x38,0x7C,0x7E,0xC6,0x82,0x82,0xC6,0x7E,0x7C,0x38,0x00,//8 0x00,0x1E,0x3F,0x7F,0x61,0x40,0x40,0x61,0x7F,0x3F,0x1E,0x00, 0x00,0xF8,0xFC,0xFE,0x06,0x02,0x06,0xFE,0xFC,0xF0,0x00,0x00,//9 0x00,0x30,0x71,0x73,0x63,0x42,0x73,0x3F,0x1F,0x07,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//. 0x00,0x00,0x00,0x38,0x38,0x38,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,//- 0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00 }; const PROGMEM uint8_t Tab_Ascii_5x72[95][5]={ /*全體ASCII 列表:5x7點陣*/ 0x00,0x00,0x00,0x00,0x00,//space 0x00,0x00,0x4f,0x00,0x00,//! 0x00,0x07,0x00,0x07,0x00,//" 0x14,0x7f,0x14,0x7f,0x14,//# 0x24,0x2a,0x7f,0x2a,0x12,//$ 0x23,0x13,0x08,0x64,0x62,//% 0x36,0x49,0x55,0x22,0x50,//& 0x00,0x05,0x07,0x00,0x00,//] 0x00,0x1c,0x22,0x41,0x00,//( 0x00,0x41,0x22,0x1c,0x00,//) 0x14,0x08,0x3e,0x08,0x14,//* 0x08,0x08,0x3e,0x08,0x08,//+ 0x00,0x50,0x30,0x00,0x00,//, 0x08,0x08,0x08,0x08,0x08,//- 0x00,0x60,0x60,0x00,0x00,//. 0x20,0x10,0x08,0x04,0x02,/// 0x3e,0x51,0x49,0x45,0x3e,//0 0x00,0x42,0x7f,0x40,0x00,//1 0x42,0x61,0x51,0x49,0x46,//2 0x21,0x41,0x45,0x4b,0x31,//3 0x18,0x14,0x12,0x7f,0x10,//4 0x27,0x45,0x45,0x45,0x39,//5 0x3c,0x4a,0x49,0x49,0x30,//6 0x01,0x71,0x09,0x05,0x03,//7 0x36,0x49,0x49,0x49,0x36,//8 0x06,0x49,0x49,0x29,0x1e,//9 0x00,0x36,0x36,0x00,0x00,//: 0x00,0x56,0x36,0x00,0x00,//; 0x08,0x14,0x22,0x41,0x00,//< 0x14,0x14,0x14,0x14,0x14,//= 0x00,0x41,0x22,0x14,0x08,//> 0x02,0x01,0x51,0x09,0x06,//? 0x32,0x49,0x79,0x41,0x3e,//@ 0x7e,0x11,0x11,0x11,0x7e,//A 0x7f,0x49,0x49,0x49,0x36,//B 0x3e,0x41,0x41,0x41,0x22,//C 0x7f,0x41,0x41,0x22,0x1c,//D 0x7f,0x49,0x49,0x49,0x41,//E 0x7f,0x09,0x09,0x09,0x01,//F 0x3e,0x41,0x49,0x49,0x7a,//G 0x7f,0x08,0x08,0x08,0x7f,//H 0x00,0x41,0x7f,0x41,0x00,//I 0x20,0x40,0x41,0x3f,0x01,//J 0x7f,0x08,0x14,0x22,0x41,//K 0x7f,0x40,0x40,0x40,0x40,//L 0x7f,0x02,0x0c,0x02,0x7f,//M 0x7f,0x04,0x08,0x10,0x7f,//N 0x3e,0x41,0x41,0x41,0x3e,//O 0x7f,0x09,0x09,0x09,0x06,//P 0x3e,0x41,0x51,0x21,0x5e,//Q 0x7f,0x09,0x19,0x29,0x46,//R 0x46,0x49,0x49,0x49,0x31,//S 0x01,0x01,0x7f,0x01,0x01,//T 0x3f,0x40,0x40,0x40,0x3f,//U 0x1f,0x20,0x40,0x20,0x1f,//V 0x3f,0x40,0x38,0x40,0x3f,//W 0x63,0x14,0x08,0x14,0x63,//X 0x07,0x08,0x70,0x08,0x07,//Y 0x61,0x51,0x49,0x45,0x43,//Z 0x00,0x7f,0x41,0x41,0x00,//[ 0x02,0x04,0x08,0x10,0x20,// 0x00,0x41,0x41,0x7f,0x00,//] 0x04,0x02,0x01,0x02,0x04,//^ 0x40,0x40,0x40,0x40,0x40,//_ 0x01,0x02,0x04,0x00,0x00,//` 0x20,0x54,0x54,0x54,0x78,//a 0x7f,0x48,0x48,0x48,0x30,//b 0x38,0x44,0x44,0x44,0x44,//c 0x30,0x48,0x48,0x48,0x7f,//d 0x38,0x54,0x54,0x54,0x58,//e 0x00,0x08,0x7e,0x09,0x02,//f 0x48,0x54,0x54,0x54,0x3c,//g 0x7f,0x08,0x08,0x08,0x70,//h 0x00,0x00,0x7a,0x00,0x00,//i 0x20,0x40,0x40,0x3d,0x00,//j 0x7f,0x20,0x28,0x44,0x00,//k 0x00,0x41,0x7f,0x40,0x00,//l 0x7c,0x04,0x38,0x04,0x7c,//m 0x7c,0x08,0x04,0x04,0x78,//n 0x38,0x44,0x44,0x44,0x38,//o 0x7c,0x14,0x14,0x14,0x08,//p 0x08,0x14,0x14,0x14,0x7c,//q 0x7c,0x08,0x04,0x04,0x08,//r 0x48,0x54,0x54,0x54,0x24,//s 0x04,0x04,0x3f,0x44,0x24,//t 0x3c,0x40,0x40,0x40,0x3c,//u 0x1c,0x20,0x40,0x20,0x1c,//v 0x3c,0x40,0x30,0x40,0x3c,//w 0x44,0x28,0x10,0x28,0x44,//x 0x04,0x48,0x30,0x08,0x04,//y 0x44,0x64,0x54,0x4c,0x44,//z 0x08,0x36,0x41,0x41,0x00,//{ 0x00,0x00,0x77,0x00,0x00,//| 0x00,0x41,0x41,0x36,0x08,//} 0x04,0x02,0x02,0x02,0x01,//~ }; /////////////// #define Start_T1 TCCR1B|=_BV(CS11);TCNT1=0//復位預計分頻器并開啟定時器T1 #define Stop_T1 TCCR1B&=~_BV(CS11) //關閉定時器T1 //數碼管的段碼編碼 unsigned char table[10] = {0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; volatile unsigned char i,j,k; volatile unsigned char IRcode; //定義一個長度為4字節的無符號long類型變量來存儲代碼 volatile unsigned char IR_OK=0; //IR信號接收有效 當程序響應接收以后請馬上清零 這樣才會繼續接收下一IR碼 volatile unsigned char IR_con=0; //IR信號當前接收位 0時表示第0位即同步碼(4.5ms高電平) volatile unsigned int Pulse_length=0; //捕獲的脈沖寬度 volatile unsigned char ICP_Parity=0; //捕獲中斷奇偶次計數 1時為偶次 并在此時判斷脈寬 volatile unsigned char address; volatile unsigned char code_data; volatile unsigned char code_data1; unsigned char clrbit; #define FREQ 8 //定義單片機工作頻率為 4M /////////////// //**************************************************************** // 函數名稱：DelayLcd // 函數功能：延時 // 入口參數： // 出口參數： //***************************************************************** void DelayLcd(uint16 i) { uint16 j; for(j=200;j>0;j--) for(;i>0;i--); //while(i--); } //**************************************************************** // 函數名稱：LcdWriteCommand // 函數功能：寫指令到LCD模塊 // 入口參數：數據 // 出口參數： //***************************************************************** void LcdWriteCommand(uint8 data1) // { uint8 i ; P_LCDCS0 ; P_LCDRS0 ; for(i=8;i>0;i--) { P_LCDCLK0; if(data1&0x80) P_LCDDAT1; else P_LCDDAT0; P_LCDCLK1; data1 <<= 1; } } //**************************************************************** // 函數名稱：LcdWritedata // 函數功能：寫數據到LCD模塊 // 入口參數：數據 // 出口參數： //***************************************************************** void LcdWritedata(uint8 data1) // { uint8 i; P_LCDCS0 ; P_LCDRS1 ; for(i=8;i>0;i--) { P_LCDCLK0; if(data1&0x80) P_LCDDAT1; else P_LCDDAT0; P_LCDCLK1; data1 <<= 1; } } //**************************************************************** // 函數名稱：Lcd_SetAddr // 函數功能：設置LCD顯示地址 // 入口參數： 頁地址 列地址 // 出口參數： //***************************************************************** void Lcd_SetAddr(uint8 page,uint8 column) { //LcdWriteCommand(0xb0 | (y+yy)); //LcdWriteCommand(0x10 | (x>>4)); //LcdWriteCommand(0x00 | (x&0x0f)); //P_LCDCS0 ; LcdWriteCommand(0xb0|page); /*設置頁地址*/ LcdWriteCommand((column>>4)|0x10); /*設置列地址的高4位*/ LcdWriteCommand(column&0x0f); /*設置列地址的低4位*/ } ////// void Display_Graphic_32x2(uint8 page,uint8 column,PROGMEM uint8_t *dp) // 電池顯示 0、2、4、6、8、10 { uint8 i,j; uint8 page_address; uint8 column_address_L,column_address_H; page_address = 0xb0|page; column_address_L =(column&0x0f); column_address_H =(column>>4)|0x10; P_LCDCS0 ; for(j=0;j<2;j++) { LcdWriteCommand(page_address+j); /*設置頁地址*/ LcdWriteCommand(column_address_H); /*設置列地址的高4位*/ LcdWriteCommand(column_address_L); /*設置列地址的低4位*/ for (i=32;i>0;i--) //寫32行 { LcdWritedata(pgm_read_byte(dp++)); /*寫數據到LCD,每寫完一個8位的數據后列地址自動加1*/ } LcdWritedata(0x00); } P_LCDCS1 ; } //#ifdef Display_Graphic_32x32_CALL void Display_Graphic_32x32(uint8 page,uint8 column,PROGMEM uint8_t *dp) { uint8 i,j; uint8 page_address; uint8 column_address_L,column_address_H; page_address = 0xb0|page; column_address_L =(column&0x0f); column_address_H =(column>>4)|0x10; P_LCDCS0 ; &
標簽： 程序
上傳時間： 2016-03-03
上傳用戶：彥 yan
實驗源代碼 //Warshall.cpp #include<stdio.h> void warshall(int k,int n) { int i , j, t; int temp[20][20]; for(int a=0;a<k;a++) { printf("請輸入矩陣第%d 行元素:",a); for(int b=0;b<n;b++) { scanf ("%d",&temp[a][b]); } } for(i=0;i<k;i++){ for( j=0;j<k;j++){ if(temp[ j][i]==1) { for(t=0;t<n;t++) { temp[ j][t]=temp[i][t]||temp[ j][t]; } } } } printf("可傳遞閉包關系矩陣是:\n"); for(i=0;i<k;i++) { for( j=0;j<n;j++) { printf("%d", temp[i][ j]); } printf("\n"); } } void main() { printf("利用 Warshall 算法求二元關系的可傳遞閉包\n"); void warshall(int,int); int k , n; printf("請輸入矩陣的行數 i: "); scanf("%d",&k); 四川大學實驗報告 printf("請輸入矩陣的列數 j: "); scanf("%d",&n); warshall(k,n); }
上傳時間： 2016-06-27
上傳用戶：梁雪文以
/****************temic*********t5557***********************************/ #include <at892051.h> #include <string.h> #include <intrins.h> #include <stdio.h> #define uchar unsigned char #define uint unsigned int #define ulong unsigned long //STC12C2051AD的SFR定義 sfr WDT_CONTR = 0xe1;//stc2051的看門狗?????? /**********全局常量************/ //寫卡的命令 #define write_command0 0//寫密碼 #define write_command1 1//寫配置字 #define write_command2 2//密碼寫數據 #define write_command3 3//喚醒 #define write_command4 4//停止命令 #define TRUE 1 #define FALSE 0 #define OK 0 #define ERROR 255 //讀卡的時間參數us #define ts_min 250//270*11.0592/12=249//取近似的整數 #define ts_max 304//330*11.0592/12=304 #define t1_min 73//90*11.0592/12=83:-10調整 #define t1_max 156//180*11.0592/12=166 #define t2_min 184//210*11.0592/12=194 #define t2_max 267//300*11.0592/12=276 //***********不采用中斷處理:采用查詢的方法讀卡時關所有中斷****************/ sbit p_U2270B_Standby = P3^5;//p_U2270B_Standby PIN=13 sbit p_U2270B_CFE = P3^3;//p_U2270B_CFE PIN=6 sbit p_U2270B_OutPut = P3^7;//p_U2270B_OutPut PIN=2 sbit wtd_sck = P1^7;//SPI總線 sbit wtd_si = P1^3; sbit wtd_so = P1^2; sbit iic_data = P1^2;//lcd IIC sbit iic_clk = P1^7; sbit led_light = P1^6;//測試綠燈 sbit led_light1 = P1^5;//測試紅燈 sbit led_light_ok = P1^1;//讀卡成功標志 sbit fengmingqi = P1^5; /***********全局變量************************************/ uchar data Nkey_a[4] = {0xA0, 0xA1, 0xA2, 0xA3};//初始密碼 //uchar idata card_snr[4]; //配置字 uchar data bankdata[28] = {1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7}; //存儲卡上用戶數據(1-7)7*4=28 uchar data cominceptbuff[6] = {1,2,3,4,5,6};//串口接收數組ram uchar command; //第一個命令 uchar command1;// //uint temp; uchar j,i; uchar myaddr = 8; //uchar ywqz_count,time_count; //ywqz jishu: uchar bdata DATA; sbit BIT0 = DATA^0; sbit BIT1 = DATA^1; sbit BIT2 = DATA^2; sbit BIT3 = DATA^3; sbit BIT4 = DATA^4; sbit BIT5 = DATA^5; sbit BIT6 = DATA^6; sbit BIT7 = DATA^7; uchar bdata DATA1; sbit BIT10 = DATA1^0; sbit BIT11 = DATA1^1; sbit BIT12 = DATA1^2; sbit BIT13 = DATA1^3; sbit BIT14 = DATA1^4; sbit BIT15 = DATA1^5; sbit BIT16 = DATA1^6; sbit BIT17 = DATA1^7; bit i_CurrentLevel;//i_CurrentLevel BIT 00H(Saves current level of OutPut pin of U2270B) bit timer1_end; bit read_ok = 0; //緩存定時值,因用同一個定時器 union HLint { uint W; struct { uchar H;uchar L; } B; };//union HLint idata a union HLint data a; //緩存定時值,因用同一個定時器 union HLint0 { uint W; struct { uchar H; uchar L; } B; };//union HLint idata a union HLint0 data b; /**********************函數原型*****************/ //讀寫操作 void f_readcard(void);//全部讀出1~7 AOR喚醒 void f_writecard(uchar x);//根據命令寫不同的內容和操作 void f_clearpassword(void);//清除密碼 void f_changepassword(void);//修改密碼 //功能子函數 void write_password(uchar data *data p);//寫初始密碼或數據 void write_block(uchar x,uchar data *data p);//不能用通用指針 void write_bit(bit x);//寫位 /*子函數區*****************************************************/ void delay_2(uint x) //延時,時間x*10us@12mhz,最小20us@12mhz { x--; x--; while(x) { _nop_(); _nop_(); x--; } _nop_();//WDT_CONTR=0X3C;不能頻繁的復位 _nop_(); } ///////////////////////////////////////////////////////////////////// void initial(void) { SCON = 0x50; //串口方式1,允許接收 //SCON =0x50; //01010000B:10位異步收發,波特率可變,SM2=0不用接收到有效停止位才RI=1, //REN=1允許接收 TMOD = 0x21; //定時器1 定時方式2(8位),定時器0 定時方式1(16位) TCON = 0x40; //設定時器1 允許開始計時(IT1=1) TH1 = 0xfD; //FB 18.432MHz 9600 波特率 TL1 = 0xfD; //fd 11.0592 9600 IE = 0X90; //EA=ES=1 TR1 = 1; //啟動定時器 WDT_CONTR = 0x3c;//使能看門狗 p_U2270B_Standby = 0;//單電源 PCON = 0x00; IP = 0x10;//uart you xian XXXPS PT1 PX1 PT0 PX0 led_light1 = 1; led_light = 0; p_U2270B_OutPut = 1; } /************************************************/ void f_readcard()//讀卡 { EA = 0;//全關,防止影響跳變的定時器計時 WDT_CONTR = 0X3C;//喂狗 p_U2270B_CFE = 1;// delay_2(232); //>2.5ms /* // aor 用喚醒功能來防碰撞 p_U2270B_CFE = 0; delay_2(18);//start gap>150us write_bit(1);//10=操作碼讀0頁 write_bit(0); write_password(&bankdata[24]);//密碼block7 p_U2270B_CFE =1 ;// delay_2(516);//編程及確認時間5.6ms */ WDT_CONTR = 0X3C;//喂狗 led_light = 0; b.W = 0; while(!(read_ok == 1)) { //while(p_U2270B_OutPut);//等一個穩定的低電平?超時判斷? while(!p_U2270B_OutPut);//等待上升沿的到來同步信號檢測1 TR0 = 1; //deng xia jiang while(p_U2270B_OutPut);//等待下降沿 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//定時器晚啟動10個周期 //同步頭 if((324 < a.W) && (a.W < 353)) ;//檢測同步信號1 else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //等待上升沿 while(!p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//b.N1<<=8; if(a.B.L < 195);//0.5p else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //讀0~7塊的數據 for(j = 0;j < 28;j++) { //uchar i; for(i = 0;i < 16;i++)//8個位 { //等待下降沿的到來 while(p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_max < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2;//先左移再賦值 b.B.L += 0xc0; i++; } else if(t1_min < a.B.L/*)&&(a.B.L < t1_max)*/)//0.5p { b.W >>= 1; b.B.L += 0x80; } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; while(!p_U2270B_OutPut);//上升 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_min < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2; i++; } else if(t1_min < a.B.L/*a.W)&&(a.B.L < t1_max)*/)//0.5P //else if(!(a.W==0)) { b.W >>= 1; //temp+=0x00; //led_light1=0;led_light=1;delay_2(40000); } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; } //取出奇位 DATA = b.B.L; BIT13 = BIT7; BIT12 = BIT5; BIT11 = BIT3; BIT10 = BIT1; DATA = b.B.H; BIT17 = BIT7; BIT16 = BIT5; BIT15 = BIT3; BIT14 = BIT1; bankdata[j] = DATA1; } read_ok = 1;//讀卡完成了 read_error: _nop_(); } } /***************************************************/ void f_writecard(uchar x)//寫卡 { p_U2270B_CFE = 1; delay_2(232); //>2.5ms //psw=0 standard write if (x == write_command0)//寫密碼:初始化密碼 { uchar i; uchar data *data p; p = cominceptbuff; p_U2270B_CFE = 0; delay_2(31);//start gap>330us write_bit(1);//寫操作碼1:10 write_bit(0);//寫操作碼0 write_bit(0);//寫鎖定位0 for(i = 0;i < 35;i++) { write_bit(1);//寫數據位1 } p_U2270B_CFE = 1; led_light1 = 0; led_light = 1; delay_2(40000);//測試使用 //write_block(cominceptbuff[4],p); p_U2270B_CFE = 1; bankdata[20] = cominceptbuff[0];//密碼存入 bankdata[21] = cominceptbuff[1]; bankdata[22] = cominceptbuff[2]; bankdata[23] = cominceptbuff[3]; } else if (x == write_command1)//配置卡參數:初始化 { uchar data *data p; p = cominceptbuff; write_bit(1);//寫操作碼1:10 write_bit(0);//寫操作碼0 write_bit(0);//寫鎖定位0 write_block(cominceptbuff[4],p); p_U2270B_CFE= 1; } //psw=1 pssword mode else if(x == write_command2) //密碼寫數據 { uchar data*data p; p = &bankdata[24]; write_bit(1);//寫操作碼1:10 write_bit(0);//寫操作碼0 write_password(p);//發口令 write_bit(0);//寫鎖定位0 p = cominceptbuff; write_block(cominceptbuff[4],p);//寫數據 } else if(x == write_command3)//aor //喚醒 { //cominceptbuff[1]操作碼10 X xxxxxB uchar data *data p; p = cominceptbuff; write_bit(1);//10 write_bit(0); write_password(p);//密碼 p_U2270B_CFE = 1;//此時數據不停的循環傳出 } else //停止操作碼 { write_bit(1);//11 write_bit(1); p_U2270B_CFE = 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /************************************/ void f_clearpassword()//清除密碼 { uchar data *data p; uchar i,x; p = &bankdata[24];//原密碼 p_U2270B_CFE = 0; delay_2(18);//start gap>150us //操作碼10:10xxxxxxB write_bit(1); write_bit(0); for(x = 0;x < 4;x++)//發原密碼 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT0); DATA >>= 1; } } write_bit(0);//鎖定位0:0 p = &cominceptbuff[0]; write_block(0x00,p);//寫新配置參數:pwd=0 //密碼無效:即清除密碼 DATA = 0x00;//停止操作碼00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /*********************************/ void f_changepassword()//修改密碼 { uchar data *data p; uchar i,x,addr; addr = 0x07;//block7 p = &Nkey_a[0];//原密碼 DATA = 0x80;//操作碼10:10xxxxxxB for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } for(x = 0;x < 4;x++)//發原密碼 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT7); DATA >>= 1; } } write_bit(0);//鎖定位0:0 p = &cominceptbuff[0]; write_block(0x07,p);//寫新密碼 p_U2270B_CFE = 1; bankdata[24] = cominceptbuff[0];//密碼存入 bankdata[25] = cominceptbuff[1]; bankdata[26] = cominceptbuff[2]; bankdata[27] = cominceptbuff[3]; DATA = 0x00;//停止操作碼00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /***************************子函數***********************************/ void write_bit(bit x)//寫一位 { if(x) { p_U2270B_CFE = 1; delay_2(32);//448*11.0592/120=42延時448us p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26寫1 } else { p_U2270B_CFE = 1; delay_2(92);//192*11.0592/120=18 p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26寫0 } } /*******************寫一個block*******************/ void write_block(uchar addr,uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)//block0數據 { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } DATA = addr <<= 5;//0地址 for(i = 0;i < 3;i++) { write_bit(BIT7); DATA <<= 1; } } /*************************************************/ void write_password(uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)// { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } } /*************************************************/ void main() { initial(); TI = RI = 0; ES = 1; EA = 1; delay_2(28); //f_readcard(); while(1) { f_readcard(); //讀卡 f_writecard(command1); //寫卡 f_clearpassword(); //清除密碼 f_changepassword(); //修改密碼 } }
標簽： 12345
上傳時間： 2017-10-20
上傳用戶：my_lcs
已知系統函數為H(z)=1/[(1-0.2z^-1)(1-0.3z^-1)(1+0.4z^-1)]。試用長除法求h(n)的6點輸出。 答案：clc;clear all;b=1;a=poly([0.2,0.3,-0.4]);x=deconv([1,zeros(1,6+4-1-1)],a)
上傳時間： 2017-10-21
上傳用戶：zhouhua
#include "iostream" using namespace std; class Matrix { private: double** A; //矩陣A double *b; //向量b public: int size; Matrix(int ); ~Matrix(); friend double* Dooli(Matrix& ); void Input(); void Disp(); }; Matrix::Matrix(int x) { size=x; //為向量b分配空間并初始化為0 b=new double [x]; for(int j=0;j<x;j++) b[j]=0; //為向量A分配空間并初始化為0 A=new double* [x]; for(int i=0;i<x;i++) A[i]=new double [x]; for(int m=0;m<x;m++) for(int n=0;n<x;n++) A[m][n]=0; } Matrix::~Matrix() { cout<<"正在析構中~~~~"<<endl; delete b; for(int i=0;i<size;i++) delete A[i]; delete A; } void Matrix::Disp() { for(int i=0;i<size;i++) { for(int j=0;j<size;j++) cout<<A[i][j]<<" "; cout<<endl; } } void Matrix::Input() { cout<<"請輸入A:"<<endl; for(int i=0;i<size;i++) for(int j=0;j<size;j++){ cout<<"第"<<i+1<<"行"<<"第"<<j+1<<"列:"<<endl; cin>>A[i][j]; } cout<<"請輸入b:"<<endl; for(int j=0;j<size;j++){ cout<<"第"<<j+1<<"個:"<<endl; cin>>b[j]; } } double* Dooli(Matrix& A) { double *Xn=new double [A.size]; Matrix L(A.size),U(A.size); //分別求得U，L的第一行與第一列 for(int i=0;i<A.size;i++) U.A[0][i]=A.A[0][i]; for(int j=1;j<A.size;j++) L.A[j][0]=A.A[j][0]/U.A[0][0]; //分別求得U，L的第r行，第r列 double temp1=0,temp2=0; for(int r=1;r<A.size;r++){ //U for(int i=r;i<A.size;i++){ for(int k=0;k<r-1;k++) temp1=temp1+L.A[r][k]*U.A[k][i]; U.A[r][i]=A.A[r][i]-temp1; } //L for(int i=r+1;i<A.size;i++){ for(int k=0;k<r-1;k++) temp2=temp2+L.A[i][k]*U.A[k][r]; L.A[i][r]=(A.A[i][r]-temp2)/U.A[r][r]; } } cout<<"計算U得:"<<endl; U.Disp(); cout<<"計算L的:"<<endl; L.Disp(); double *Y=new double [A.size]; Y[0]=A.b[0]; for(int i=1;i<A.size;i++ ){ double temp3=0; for(int k=0;k<i-1;k++) temp3=temp3+L.A[i][k]*Y[k]; Y[i]=A.b[i]-temp3; } Xn[A.size-1]=Y[A.size-1]/U.A[A.size-1][A.size-1]; for(int i=A.size-1;i>=0;i--){ double temp4=0; for(int k=i+1;k<A.size;k++) temp4=temp4+U.A[i][k]*Xn[k]; Xn[i]=(Y[i]-temp4)/U.A[i][i]; } return Xn; } int main() { Matrix B(4); B.Input(); double *X; X=Dooli(B); cout<<"~~~~解得:"<<endl; for(int i=0;i<B.size;i++) cout<<"X["<<i<<"]:"<<X[i]<<" "; cout<<endl<<"呵呵呵呵呵"; return 0; }
標簽： 道理特分解法
上傳時間： 2018-05-20
上傳用戶：Aa123456789
module M_GAUSS !高斯列主元消去法模塊 contains subroutine LINEQ(A,B,X,N) !高斯列主元消去法 implicit real*8(A-Z) integer::I,K,N integer::ID_MAX !主元素標號 real*8::A(N,N),B(N),X(N) real*8::AUP(N,N),BUP(N) !A,B為增廣矩陣 real*8::AB(N,N+1) real*8::VTEMP1(N+1),VTEMP2(N+1) AB(1:N,1:N)=A AB(:,N+1)=B
標簽： fortan Newton 程序 數值分析 方程 非線性
上傳時間： 2018-06-15
上傳用戶：answer123
#include<stdio.h> #include<string.h> #include<stdlib.h> #define N 100 int iNumOfStu=0; struct score { float math; float english; float computer; }; struct student { int number; char name[20]; struct score sco; float average; }; struct student stu[N]; void print_menu(void);//輸出菜單 void choosemenu(void);//菜單選擇 void input_student1(int);//輸入學生信息 void input_student2(void);//輸入總函數 void input_student3(int &,int);//判斷學號是否重復 void input_student4(int,int);//覆蓋原信息 void sort_student3(student s[],int);//按照英語成績排序 void sort_student4(student s[],int);//按照計算機成績排序 void sort_student2(student s[],int);//按照數學成績排序 void sort_student5(student s[],int);//按照平均成績排序 float input_score2(int);//計算學生平均成績 void print_student2(void);//顯示表頭 void print_student3(int);//顯示學生信息 void print_student1(int);//顯示全部學生資料 void sort_student1(void);//排序總函數 void menu(void);//菜單調度總函數 int search_student2(int);//按學號查詢學生信息并輸出 void search_student3(int);//按平均分最高查詢并輸出 void search_student1(void);//查詢總函數 void delete_student2(int,int);//刪除學生信息 void delete_student1(void);//刪除總函數 void change_student2(int);//修改學生資料 void change_student1(void);//修改總函數 void input_score3(int);//統計成績 void input_score1(void);//統計成績總函數 void print_help(void);//輸出幫助信息 void exit_student(void);//退出系統 void save_student(student *,int);//保存學生信息 void main() { menu(); } void save_student(student *s,int a)//保存學生信息 { FILE *fp; if((fp=fopen("d:\\學生信息.txt","wb"))==NULL) { printf("不能打開文件！\n"); } else { printf("保存信息到D盤\n"); fprintf(fp,"本班所有學生具體信息如下：\r\n"); fprintf(fp," 學號 姓名 數學成績 英語成績 計算機成績 平均成績\r\n"); for(int i=0;i<a;i++) { fprintf(fp,"%8d%12s%14.2f%14.2f%14.2f%14.2f\n",stu[i].number,stu[i].name,stu[i].sco.math,stu[i].sco.english,stu[i].sco.computer,stu[i].average); fprintf(fp,"\r\n"); } fclose(fp); printf("信息保存成功！\n"); } } void exit_student(void)//退出系統 { exit(1); } void print_help(void)//輸出幫助信息 { printf("本系統所能容納的最大學生數為%d人\n學生信息保存在D盤根目錄下，保存文件為“學生信息.txt”。\n感謝使用！\n",N); } void input_score1(void)//統計成績總函數 { int c; c=search_student2(iNumOfStu); printf("學號：%d\n",stu[c].number); printf("姓名：%s\n",stu[c].name); input_score3(c); printf("新成績錄入成功！\n"); stu[c].average=input_score2(c); } void input_score3(int a)//統計成績 { printf("數學新成績："); scanf("%f",&stu[a].sco.math); printf("英語新成績："); scanf("%f",&stu[a].sco.english); printf("計算機新成績："); scanf("%f",&stu[a].sco.computer); } void change_student2(int a)//修改學生資料 { printf("學號：%d----修改為：",stu[a].number); scanf("%d",&stu[a].number); getchar(); printf("姓名：%s----修改為：",stu[a].name); gets(stu[a].name); printf("數學成績：%.2f----修改為：",stu[a].sco.math); scanf("%f",&stu[a].sco.math); printf("英語成績：%.2f----修改為：",stu[a].sco.english); scanf("%f",&stu[a].sco.english); printf("計算機成績：%.2f----修改為：",stu[a].sco.computer); scanf("%f",&stu[a].sco.computer); } void change_student1(void)//修改總函數 { int c; c=search_student2(iNumOfStu); getchar(); printf("是否要修改此學生信息？（“y”代表是）"); char d; scanf("%c",&d); if(d=='y'||d=='Y') { change_student2(c); stu[c].average=input_score2(c); printf("信息修改成功！\n"); } } void delete_student1(void)//刪除總函數 { int c; c=search_student2(iNumOfStu); getchar(); printf("是否刪除此條記錄？（“y”代表是）"); char d; scanf("%c",&d); if(d=='y'||d=='Y') { delete_student2(c,iNumOfStu); printf("記錄已刪除！\n"); } } void delete_student2(int a,int b)//刪除學生信息 { for(int i=a;i<b-1;i++) { stu[i]=stu[i+1]; } --iNumOfStu; } void search_student1(void)//查詢總函數 { printf("1、按學號查詢\n2、按平均分最高查詢\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { search_student2(iNumOfStu); break; } case 2: { search_student3(iNumOfStu); break; } default: break; } } void menu(void)//菜單調度總函數 { print_menu(); choosemenu(); } void sort_student1(void)//排序總函數 { printf("1、按數學成績排序\n2、按英語成績排序\n3、按計算機成績排序\n4、按平均成績排序\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { sort_student2(stu,iNumOfStu); break; } case 2: { sort_student3(stu,iNumOfStu); break; } case 3: { sort_student4(stu,iNumOfStu); break; } case 4: { sort_student5(stu,iNumOfStu); break; } default: break; } } void print_student1(int a)//顯示全部學生資料 { printf("本班所有學生具體信息如下\n"); print_student2(); for(int i=0;i<a;i++) { print_student3(i); } } void print_student3(int a)//顯示學生信息 { printf("%8d%12s%14.2f%14.2f%14.2f%14.2f\n",stu[a].number,stu[a].name,stu[a].sco.math,stu[a].sco.english,stu[a].sco.computer,stu[a].average); } void print_student2(void)//顯示表頭 { printf(" 學號 姓名 數學成績 英語成績 計算機成績 平均成績\n"); } void input_student4(int a,int b)//覆蓋原信息 { stu[a]=stu[b-1]; --iNumOfStu; } void input_student3(int &a,int b)//判斷學號是否重復 { if(a!=0) { int i=0; do { if(stu[a].number==stu[i].number) { printf("此學號代表的學生已錄入\n1、覆蓋原信息\n2、重新輸入\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { input_student4(i,iNumOfStu); a=iNumOfStu-1; printf("信息已替換！\n"); break; } case 2: { printf("請重新輸入學生信息：\n"); input_student1(iNumOfStu-1); break; } default: break; } break; } ++i; } while(i<b-1); } } void print_menu(void)//輸出菜單 { printf("======歡迎來到學生信息管理系統======\n"); printf(" 1、輸入學生資料\n"); printf(" 2、刪除學生資料\n"); printf(" 3、查詢學生資料\n"); printf(" 4、修改學生資料\n"); printf(" 5、顯示學生資料\n"); printf(" 6、統計學生成績\n"); printf(" 7、排序學生成績\n"); printf(" 8、保存學生資料\n"); printf(" 9、獲取幫助信息\n"); printf(" 10、退出系統\n"); printf("====================================\n"); printf("請選擇："); } void input_student2(void)//輸入總函數 { char end; printf("請輸入學生信息（在最后一個學生信息錄入完成后以“/”結束錄入）：\n"); for(int i=0;(end=getchar())!='/';i++) { input_student1(i); ++iNumOfStu; input_student3(i,iNumOfStu); } for(int j=0;j<iNumOfStu;j++) { stu[j].average=input_score2(j); } } void input_student1(int a)//輸入學生信息 { printf("學號："); scanf("%d",&stu[a].number); getchar(); printf("姓名："); gets(stu[a].name); printf("數學成績："); scanf("%f",&stu[a].sco.math); printf("英語成績："); scanf("%f",&stu[a].sco.english); printf("計算機成績："); scanf("%f",&stu[a].sco.computer); } float input_score2(int a)//計算學生平均成績 { return (stu[a].sco.math+stu[a].sco.english+stu[a].sco.computer)/3; } void search_student3(int a)//按平均分最高查詢并輸出 { int max=0; for(int i=0;i<a;i++) { if(stu[max].average<stu[i].average) { max=i; } } print_student2(); print_student3(max); } void sort_student2(student s[],int a)//按照數學成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.math>stu[max].sco.math) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student3(student s[],int a)//按照英語成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.english>stu[max].sco.english) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student4(student s[],int a)//按照計算機成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.computer>stu[max].sco.computer) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student5(student s[],int a)//按照平均成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].average>stu[max].average) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } int search_student2(int a)//按照學號查找學生并輸出 { int num; int c; printf("請輸入要查詢的學號："); scanf("%d",&num); for(int i=0;i<a;i++) { if(num==stu[i].number) { c=i; } } printf("此學生的信息是：\n"); print_student2(); print_student3(c); return c; } void choosemenu(void)//菜單選擇 { int i; scanf("%d",&i); switch(i) { case 1: { input_student2(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 2: { delete_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 3: { search_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 4: { change_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 5: { print_student1(iNumOfStu); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 6: { input_score1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 7: { sort_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 8: { save_student(stu,iNumOfStu); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 9: { print_help(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 10: { exit_student(); } default: break; } } 運行結果： 源文件下載地址： http://115.com/file/clnq138g#一個簡單的學生成績管理系統.rar （請將此地址復制到瀏覽器地址欄中訪問下載頁面）
標簽： 成績查詢系統
上傳時間： 2019-06-08
上傳用戶：啊的撒旦
#include<stdio.h> #include<string.h> #include<stdlib.h> #define N 100 int iNumOfStu=0; struct score { float math; float english; float computer; }; struct student { int number; char name[20]; struct score sco; float average; }; struct student stu[N]; void print_menu(void);//輸出菜單 void choosemenu(void);//菜單選擇 void input_student1(int);//輸入學生信息 void input_student2(void);//輸入總函數 void input_student3(int &,int);//判斷學號是否重復 void input_student4(int,int);//覆蓋原信息 void sort_student3(student s[],int);//按照英語成績排序 void sort_student4(student s[],int);//按照計算機成績排序 void sort_student2(student s[],int);//按照數學成績排序 void sort_student5(student s[],int);//按照平均成績排序 float input_score2(int);//計算學生平均成績 void print_student2(void);//顯示表頭 void print_student3(int);//顯示學生信息 void print_student1(int);//顯示全部學生資料 void sort_student1(void);//排序總函數 void menu(void);//菜單調度總函數 int search_student2(int);//按學號查詢學生信息并輸出 void search_student3(int);//按平均分最高查詢并輸出 void search_student1(void);//查詢總函數 void delete_student2(int,int);//刪除學生信息 void delete_student1(void);//刪除總函數 void change_student2(int);//修改學生資料 void change_student1(void);//修改總函數 void input_score3(int);//統計成績 void input_score1(void);//統計成績總函數 void print_help(void);//輸出幫助信息 void exit_student(void);//退出系統 void save_student(student *,int);//保存學生信息 void main() { menu(); } void save_student(student *s,int a)//保存學生信息 { FILE *fp; if((fp=fopen("d:\\學生信息.txt","wb"))==NULL) { printf("不能打開文件！\n"); } else { printf("保存信息到D盤\n"); fprintf(fp,"本班所有學生具體信息如下：\r\n"); fprintf(fp," 學號 姓名 數學成績 英語成績 計算機成績 平均成績\r\n"); for(int i=0;i<a;i++) { fprintf(fp,"%8d%12s%14.2f%14.2f%14.2f%14.2f\n",stu[i].number,stu[i].name,stu[i].sco.math,stu[i].sco.english,stu[i].sco.computer,stu[i].average); fprintf(fp,"\r\n"); } fclose(fp); printf("信息保存成功！\n"); } } void exit_student(void)//退出系統 { exit(1); } void print_help(void)//輸出幫助信息 { printf("本系統所能容納的最大學生數為%d人\n學生信息保存在D盤根目錄下，保存文件為“學生信息.txt”。\n感謝使用！\n",N); } void input_score1(void)//統計成績總函數 { int c; c=search_student2(iNumOfStu); printf("學號：%d\n",stu[c].number); printf("姓名：%s\n",stu[c].name); input_score3(c); printf("新成績錄入成功！\n"); stu[c].average=input_score2(c); } void input_score3(int a)//統計成績 { printf("數學新成績："); scanf("%f",&stu[a].sco.math); printf("英語新成績："); scanf("%f",&stu[a].sco.english); printf("計算機新成績："); scanf("%f",&stu[a].sco.computer); } void change_student2(int a)//修改學生資料 { printf("學號：%d----修改為：",stu[a].number); scanf("%d",&stu[a].number); getchar(); printf("姓名：%s----修改為：",stu[a].name); gets(stu[a].name); printf("數學成績：%.2f----修改為：",stu[a].sco.math); scanf("%f",&stu[a].sco.math); printf("英語成績：%.2f----修改為：",stu[a].sco.english); scanf("%f",&stu[a].sco.english); printf("計算機成績：%.2f----修改為：",stu[a].sco.computer); scanf("%f",&stu[a].sco.computer); } void change_student1(void)//修改總函數 { int c; c=search_student2(iNumOfStu); getchar(); printf("是否要修改此學生信息？（“y”代表是）"); char d; scanf("%c",&d); if(d=='y'||d=='Y') { change_student2(c); stu[c].average=input_score2(c); printf("信息修改成功！\n"); } } void delete_student1(void)//刪除總函數 { int c; c=search_student2(iNumOfStu); getchar(); printf("是否刪除此條記錄？（“y”代表是）"); char d; scanf("%c",&d); if(d=='y'||d=='Y') { delete_student2(c,iNumOfStu); printf("記錄已刪除！\n"); } } void delete_student2(int a,int b)//刪除學生信息 { for(int i=a;i<b-1;i++) { stu[i]=stu[i+1]; } --iNumOfStu; } void search_student1(void)//查詢總函數 { printf("1、按學號查詢\n2、按平均分最高查詢\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { search_student2(iNumOfStu); break; } case 2: { search_student3(iNumOfStu); break; } default: break; } } void menu(void)//菜單調度總函數 { print_menu(); choosemenu(); } void sort_student1(void)//排序總函數 { printf("1、按數學成績排序\n2、按英語成績排序\n3、按計算機成績排序\n4、按平均成績排序\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { sort_student2(stu,iNumOfStu); break; } case 2: { sort_student3(stu,iNumOfStu); break; } case 3: { sort_student4(stu,iNumOfStu); break; } case 4: { sort_student5(stu,iNumOfStu); break; } default: break; } } void print_student1(int a)//顯示全部學生資料 { printf("本班所有學生具體信息如下\n"); print_student2(); for(int i=0;i<a;i++) { print_student3(i); } } void print_student3(int a)//顯示學生信息 { printf("%8d%12s%14.2f%14.2f%14.2f%14.2f\n",stu[a].number,stu[a].name,stu[a].sco.math,stu[a].sco.english,stu[a].sco.computer,stu[a].average); } void print_student2(void)//顯示表頭 { printf(" 學號 姓名 數學成績 英語成績 計算機成績 平均成績\n"); } void input_student4(int a,int b)//覆蓋原信息 { stu[a]=stu[b-1]; --iNumOfStu; } void input_student3(int &a,int b)//判斷學號是否重復 { if(a!=0) { int i=0; do { if(stu[a].number==stu[i].number) { printf("此學號代表的學生已錄入\n1、覆蓋原信息\n2、重新輸入\n請選擇："); int c; scanf("%d",&c); switch(c) { case 1: { input_student4(i,iNumOfStu); a=iNumOfStu-1; printf("信息已替換！\n"); break; } case 2: { printf("請重新輸入學生信息：\n"); input_student1(iNumOfStu-1); break; } default: break; } break; } ++i; } while(i<b-1); } } void print_menu(void)//輸出菜單 { printf("======歡迎來到學生信息管理系統======\n"); printf(" 1、輸入學生資料\n"); printf(" 2、刪除學生資料\n"); printf(" 3、查詢學生資料\n"); printf(" 4、修改學生資料\n"); printf(" 5、顯示學生資料\n"); printf(" 6、統計學生成績\n"); printf(" 7、排序學生成績\n"); printf(" 8、保存學生資料\n"); printf(" 9、獲取幫助信息\n"); printf(" 10、退出系統\n"); printf("====================================\n"); printf("請選擇："); } void input_student2(void)//輸入總函數 { char end; printf("請輸入學生信息（在最后一個學生信息錄入完成后以“/”結束錄入）：\n"); for(int i=0;(end=getchar())!='/';i++) { input_student1(i); ++iNumOfStu; input_student3(i,iNumOfStu); } for(int j=0;j<iNumOfStu;j++) { stu[j].average=input_score2(j); } } void input_student1(int a)//輸入學生信息 { printf("學號："); scanf("%d",&stu[a].number); getchar(); printf("姓名："); gets(stu[a].name); printf("數學成績："); scanf("%f",&stu[a].sco.math); printf("英語成績："); scanf("%f",&stu[a].sco.english); printf("計算機成績："); scanf("%f",&stu[a].sco.computer); } float input_score2(int a)//計算學生平均成績 { return (stu[a].sco.math+stu[a].sco.english+stu[a].sco.computer)/3; } void search_student3(int a)//按平均分最高查詢并輸出 { int max=0; for(int i=0;i<a;i++) { if(stu[max].average<stu[i].average) { max=i; } } print_student2(); print_student3(max); } void sort_student2(student s[],int a)//按照數學成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.math>stu[max].sco.math) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student3(student s[],int a)//按照英語成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.english>stu[max].sco.english) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student4(student s[],int a)//按照計算機成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].sco.computer>stu[max].sco.computer) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } void sort_student5(student s[],int a)//按照平均成績排序 { struct student temp; for(int i=0;i<a-1;i++) { int max=i; for(int j=i+1;j<a;j++) if(stu[j].average>stu[max].average) { max=j; } if(max!=i) { temp=stu[max]; stu[max]=stu[i]; stu[i]=temp; } } print_student2(); for(int k=0;k<a;k++) { print_student3(k); } } int search_student2(int a)//按照學號查找學生并輸出 { int num; int c; printf("請輸入要查詢的學號："); scanf("%d",&num); for(int i=0;i<a;i++) { if(num==stu[i].number) { c=i; } } printf("此學生的信息是：\n"); print_student2(); print_student3(c); return c; } void choosemenu(void)//菜單選擇 { int i; scanf("%d",&i); switch(i) { case 1: { input_student2(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 2: { delete_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 3: { search_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 4: { change_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 5: { print_student1(iNumOfStu); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 6: { input_score1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 7: { sort_student1(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 8: { save_student(stu,iNumOfStu); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 9: { print_help(); printf("按回車鍵返回主菜單"); getchar(); getchar(); menu(); break; } case 10: { exit_student(); } default: break; } } 運行結果： 源文件下載地址： http://115.com/file/clnq138g#一個簡單的學生成績管理系統.rar （請將此地址復制到瀏覽器地址欄中訪問下載頁面） #include<stdio.h> #include<string.h> #include<stdlib.h> #define N 100 int iNumOfStu=0; struct score { float math; float english; float computer; }; struct student { int number; char name[20]; struct score sco; float average; }; struct student stu[N]; void print_menu(void);//輸出菜單 void choosemenu(void);//菜單選擇 void input_student1(int);//輸入學生信息 void input_student2(void);//輸入總函數 void input_student3(int &,int);//判斷學號是否重復 void input_student4(int,int);//覆蓋原信息 void sort_student3(student s[],int);//按照英語成績排序 void sort_student4(student s[],int);//按照計算機成績排序 void sort_student2(student s[],int);//按照數學成績排序 void sort_student5(student s[],int);//按照平均成績排序 float input_score2(int);//計算學生平均成績 void print_student2(void);//顯示表頭 void print_student3(int);//顯示學生信息 void print_student1(int);//顯示全部學生資料 void sort_student1(void);//排序總函數 void menu(void);//菜單調度總函數 int search_student2(int);//按學號查詢學生信息并輸出 void search_student3(int);//按平均分最高查詢并輸出 void search_student1(void);//查詢總函數 void delete_student2(int,int);//刪除學生信息 void delete_student1(void);//刪除總函數 void change_student2(int);//修改學生資料 void change_student1(void);//修改總函數 void input_score3(int);//統計成績 void input_score1(void);//統計成績總函數 void print_help(void);//輸出幫助信息 void exit_student(void);//退出系統 void save_student(student *,int);//保存學生信息 void main() { menu(); } void save_student(student *s,int a)//保存學生信息 { FILE *fp; if((fp=fopen("d:\\學生信息.txt","wb"))==NULL) { printf("不能打開文件！\n"); } else { printf("保存信息到D盤\n"); fprintf(fp,"本班所有學生具體信息如下：\r\n"); fprintf(fp," 學號 姓名 數學成績 英語成績 計算機成績 平均成績\r\n"); for(int i=0;i<a;i++) { fprintf(fp,"%8d%12s%14.2f%14.2f%14.2f%14.2f\n",stu[i].number,stu[i].name,stu[i].sco.math,stu[i].sco.english,stu[i].sco.computer,stu[i].average); fprintf(fp,"\r\n"); } fclose(fp); printf("信息保存成功！\n"); } } void exit_student(void)//退出系統 { exit(1); } void print_help(void)//輸出幫助信息 { printf("本系統所能容納的最大學生數為%d人\n學生信息保存在D盤根目錄下，保存文件為“學生信息.txt”。\n感謝使用！\n",N); } void input_score1(void)//統計成績總函數 { int c; c=search_student2(iNumOfStu); printf("學號：%d\n",stu[c].number); printf("姓名：%s\n",stu[c].name); input_score3(c); printf("新成績錄入成功！
標簽： c語言
上傳時間： 2019-06-09
上傳用戶：啊的撒旦
