電源開發資料,能夠使電源降壓,輸入在7--40V的范圍,輸出為5V
上傳時間： 2013-12-27
上傳用戶：sssl
The ISL8540 is a step down DC/DC power switching regulator which accepts 9.0V to 40V input and provi
標簽： Switching Regulator Power DC
上傳時間： 2013-06-07
上傳用戶：shanml
●抗線路接反功能可在線路跨接出錯時為技術員節省查找故障所消耗的大量時間； ●采用與 RS-485 相同的外引腳，無需重新設計電路板； ●總線引腳能承受 –35V 至 +40V 之間的故障，可為典型 24 Vac HVAC 電源最大限度地降低直接短路所造成的損害； ●多達 32 個節點的高輸入阻抗可在統一網絡上支持多節點，無需中繼器，從而可降低系統成本
標簽：
上傳時間： 2013-06-22
上傳用戶：624971116
General Description The LM621 is a bipolar IC designed for commutation of brushless DC motors. The part is compatible with both three- and four-phase motors. It can directly drive the power switching devices used to drive the motor. The LM621 provides an adjustable dead-time circuit to eliminate ``shootthrough'' current spiking in the power switching circuitry. Operation is from a 5V supply, but output swings of up to 40V are accommodated. The part is packaged in an 18-pin, dual-in-line package.
上傳時間： 2013-07-24
上傳用戶：sdq_123
PT4115是一款連續電感電流導通模式的降壓恒流源，用于驅動一顆或者多顆串聯LED。根據不同外部器件，芯片可以驅動高達數十瓦的LED。PT4115具有調光功能，通過DIM引腳實現模擬調光和寬范圍PWM調光。當VDIM低于0.3V時，功率開關關斷，芯片進入低功耗待機狀態 主要技術參數 ? 輸入電壓范圍：6V to 40V ? 最大輸出LED電流1.2A ? 5%的輸出電流精度 ? 高達97%的效率 ? 極少的外部器件 ? 復用DIM引腳進行LED開關、模擬調光和PWM調光 ? LED開路保護 ? LED過熱保護 ? 輸出電流可調節 ? 具有輸入欠壓保護功能 應用 ? 低壓LED射燈代替鹵素燈 ? 車載LED燈 ? LED備用燈 ? LED信號燈
上傳時間： 2014-12-24
上傳用戶：shengyj12345
基于1 μm 40V BCD 工藝，使用Cadence軟件對原邊反饋AC/DC控制器進行仿真和分析。線補償技術可以使原邊反饋AC/DC電路獲得很好的負載調整率，抵消電感上所消耗的電壓和整流二極管上的壓降，使輸出達到的最佳值。在輸入加220 V交流電壓時，輸出結果最大值為5.09 V，最小值為5 V，最大負載調整率為9.609%。
上傳時間： 2013-10-20
上傳用戶：sglccwk
LM2596開關電壓調節器是降壓型電源管理單片集成電路，能夠輸出3A的驅動電流，同時具有很好的線性和負載調節特性。固定輸出版本有3.3V、5V、12V， 可調版本可以輸出小于37V的各種電壓。 該器件內部集成頻率補償和固定頻率發生器，開關頻率為150KHz，與低頻開關調節器相比較，可以使用更小規格的濾波元件。由于該器件只需4個外接元件，可以使用通用的標準電感，這更優化了LM2596的使用，極大地簡化了開關電源電路的設計。 其封裝形式包括標準的5腳TO-220封裝（DIP）和5腳TO-263表貼封裝（SMD）。 該器件還有其他一些特點：在特定的輸入電壓和輸出負載的條件下，輸出電壓的誤差可以保證在±4%的范圍內，振蕩頻率誤差在±15%的范圍內；可以用僅80μA的待機電流， 實現外部斷電；具有自我保護電路（一個兩級降頻限流保護和一個在異常情況下斷電的過溫完全保護電路） ※ 3.3V、5V、12V的固定電壓輸出和可調電壓輸出 ※ 可調輸出電壓范圍1.2V～37V±4% ※ 輸出線性好且負載可調節 ※ 輸出電流可高達3A ※ 輸入電壓可高達40V ※ 采用150KHz的內部振蕩頻率，屬于第二代開關電壓調節器，功耗小、效率高 ※ 低功耗待機模式，IQ的典型值為80μA ※ TTL斷電能力 ※ 具有過熱保護和限流保護功能 ※ 封裝形式：TO-220（T）和TO-263（S） ※ 外圍電路簡單，僅需4個外接元件， 且使用容易購買的標準電感
上傳時間： 2014-12-24
上傳用戶：ttpay
Automobile electronic systems place high demands ontoday’s DC/DC converters. They must be able to preciselyregulate an output voltage in the face of wide temperatureand input voltage ranges—including load dump transientsin excess of 60V and cold crank voltage drops to 4V. Theconverter must also be able to minimize battery drain inalways-on systems by maintaining high effi ciency over abroad load current range. Similar demands are made bymany 48V nonisolated telecom applications, 40V FireWireperipherals and battery-powered applications with autoplug adaptors. The LT3437’s best in classperformancemeets all of these requirements in a small thermallyenhanced 3mm × 3mm DFN package.
上傳時間： 2013-10-15
上傳用戶：stampede
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間： 2013-11-18
上傳用戶：hulee
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上傳時間： 2013-11-23
上傳用戶：新手無憂
