The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
This application note provides users with a general understanding of the SVF and XSVF fileformats as they apply to Xilinx devices. Some familiarity with IEEE STD 1149.1 (JTAG) isassumed. For information on using Serial Vector Format (SVF) and Xilinx Serial Vector Format(XSVF) files in embedded programming applications
The introduction of Spartan-3™ devices has createdmultiple changes in the evolution of embedded controldesigns and pushed processing capabilities to the “almostfreestage.” With these new FPGAs falling under $20, involume, with over 1 million system gates, and under $5for 100K gate-level units, any design with programmablelogic has a readily available 8- or 16-bit processor costingless than 75 cents and 32-bit processor for less than $1.50.
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
The Xilinx Zynq-7000 Extensible Processing Platform (EPP) redefines the possibilities for embedded systems, giving system and software architects and developers a flexible platform to launch their new solutions and traditional ASIC and ASSP users an alternative that aligns with today’s programmable imperative. The new class of product elegantly combines an industrystandard ARMprocessor-based system with Xilinx 28nm programmable logic—in a single device. The processor boots first, prior to configuration of the programmable logic. This, along with a streamlined workflow, saves time and effort and lets software developers and hardware designers start development simultaneously.
針對嵌入式機器視覺系統向獨立化、智能化發展的要求，介紹了一種嵌入式視覺系統--智能相機。基于對智能相機體系結構、組成模塊和圖像采集、傳輸和處理技術的分析，對國內外的幾款智能相機進行比較。綜合技術發展現狀，提出基于FPGA+DSP模式的硬件平臺，并提出智能相機的發展方向。分析結果表明，該系統設計可以實現脫離PC運行，完成圖像獲取與分析，并作出相應輸出。
Abstract:
This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
