A version of a sparse bundle adjustment implementation with ADJUSTABLE intrinsics and distortion parameters (either shared by all views or varying for each view)
General Description
The LM621 is a bipolar IC designed for commutation of
brushless DC motors. The part is compatible with both
three- and four-phase motors. It can directly drive the power
switching devices used to drive the motor. The LM621 provides
an ADJUSTABLE dead-time circuit to eliminate ``shootthrough''
current spiking in the power switching circuitry.
Operation is from a 5V supply, but output swings of up to
40V are accommodated. The part is packaged in an 18-pin,
dual-in-line package.
設計了水聲信號發生系統中的功率放大電路，可將前級電路產生的方波信號轉換為正弦信號，同時進行濾波、功率放大，使其滿足換能器對輸入信號的要求。該電路以單片機AT89C52，集成6階巴特沃思低通濾波芯片MF6以及大功率運算放大器LM12為核心，通過標準RS232接口與PC進行通信，實現信號增益的程控調節，對干擾信號具有良好的抑制作用。經調試該電路工作穩定正常，輸出波形無失真，在輸出功率以及放大增益、波紋系數等方面均滿足設計要求。
This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is ADJUSTABLE and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and ADJUSTABLE output low-dropout linear regulators (LDOs). Test results and hardware files are included.
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and ADJUSTABLE output low-dropout linear regulator (LDO). Test results and hardware files are included.
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and ADJUSTABLE output low-dropout linearregulator (LDO). Test results and hardware files are included.
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has ADJUSTABLE frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic capacitors.
