實現ARM 芯片的一對PWM 輸出用于控制直流電機的轉動，通過A/D 旋鈕控 制其正反轉及轉速。編程實現ARM 的四路I/O 通道實現環形脈沖分配用于控制步進電機的轉動，通過 A/D 旋鈕轉角控制步進電機的轉角。
上傳時間： 2014-11-16
上傳用戶：gmh1314
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
標簽： multiplication Implement matrices matrix
上傳時間： 2014-08-30
上傳用戶：dsgkjgkjg
Assembly example with RealView MDK The Assembly example shows how to create a pure assembly program for an ARM device. It is done using the RealView Compilation Tools that are part of the RealView MDK-ARM.
標簽： Assembly example RealView assembly
上傳時間： 2015-05-30
上傳用戶：FreeSky
This a simple bootloader for AT91SAM7{S,X}{64,128,256} processors. It permits you to download new code to the device over USB. This bootrom is installed at address 0x00000000 in the ARM, which means that it is the first piece of code to execute after reset. At startup, it waits for a few seconds to see if the downloader is trying to connect. If not, then the bootloader gives up control and jumps to your program. If the downloader is trying to connect, then the bootloader receives the new program over USB and writes it into flash.
標簽： bootloader processors download permits
上傳時間： 2015-11-30
上傳用戶：shus521
ARMask.The ARM has six operating modes: • User (unprivileged mode under which most tasks run) • FIQ (entered when a high priority (fast) interrupt is raised) • IRQ (entered when a low priority (normal) interrupt is raised) • Supervisor (entered on reset and when a Software Interrupt instruction is executed) • Abort (used to handle memory access violations) • Undef (used to handle undefined instructions) * ARM Architecture Version 4 adds a seventh mode: • System (privileged mode using the same registers as user mode)
標簽： unprivileged operating ARMask modes
上傳時間： 2013-12-24
上傳用戶：bcjtao
在軟件Proteus中仿真ucos（ARM） 1.移植除了OS_CPU.h,OS_CPU_A.s,OS_CPU_C.C 三個函數外，對中斷專門用了一個函數OS_int_A.s 按其中的規則寫中斷函數即可. 2。應用實例為\ArmUCOS\App\test1\test.mcp,在周立功2104的板子上的ram中就可直接運行(code＋data<16K), 注意使用了.a庫文件(我習慣這么用) 3. 將所有的文件放到D:\ArmUCOS\下,這樣上面的文件能直接編譯.
標簽： OS_CPU_A OS_CPU_C Proteus OS_CPU
上傳時間： 2014-01-02
上傳用戶：chenbhdt
介紹了一種基于ARM 和GPRS 的遠程監控系統。以Samsung S3C2410 為中央 處理器的嵌入式系統主要完成系統的控制和數據功能,用GPRS 網絡連接Internet 實現監控中心與遠程ARM 嵌入式系統的通訊。并對遠程終端的硬件結構和監控中心軟件設計進行了介紹。
標簽： GPRS Internet Samsung S3C2410
上傳時間： 2013-12-23
上傳用戶：love_stanford
替代加密: A B C D E F G H I J K L M N O P Q R S T U V W 密文 Y Z D M R N H X J L I O Q U W A C B E G F K P 明文 X Y Z T S V I HAVE A DREAM！# 密文？？ 用ARM編程實現替代加密。
標簽： 加密
上傳時間： 2016-07-17
上傳用戶：qq521
FatFs06.rar FatFs is a generic file system module to implement the FAT file system to small embedded systems. The FatFs is written in compliance with ANSI C, therefore it is independent of hardware architecture. It can be incorporated into cheap microcontrollers, such as 8051, PIC, AVR, SH, Z80, H8, ARM and etc..., without any change.
標簽： system FatFs file implement
上傳時間： 2016-11-17
上傳用戶：chenxichenyue
The application described in this document is for a product that is subject to continuous developments and improvements. All particulars of the product and its use contained in this document are given by ARM in good faith. However, all warranties implied or expressed, including but not limited to implied warranties of merchantability, or fitness for purpose, are excluded.
標簽： application continuous developmen described
上傳時間： 2016-12-16
上傳用戶：dave520l
蟲蟲下載站版權所有 京ICP備2021023401號-1
