Assembler source code for a AT90S2313 microcontroller used in an interface for reading, programming and bulk erasing serial flash of the ST25P16 and SP25P32 family used on the WGT624v3 Netgears Router.
XT_KeyBoard interface with 8951 using Assembler and Document for Key board delivered data details, Which will help to dvelope for any processor and controller interface.
匯編器在微處理器的驗證和應用中舉足輕重，如何設計通用的匯編器一直是研究的熱點之一。本文提出了一種開放式的匯編器系統設計思想，在匯編語言與機器語言間插入中間代碼CMDL（code mapping description language）語言，打破匯編語言與機器語言的直接映射關系，由此建立起一套描述匯編語言與機器語言的開放式映射體系。基于此開放式映射體系開發了一套匯編器系統，具有較高層次上的通用性和可移植性。【關鍵詞】指令集，CMDL，匯編器，開放式
Design of Retargetable Assembler System Liu Ling Feng Wen Nan Wang Ying Chun Jiang An Ping Ji Li Jiu IME of Peking University, 100871【摘要】An assembler plays a very important role in the field of microprocessor verifications and applications, thus how to build a retargetable assembler system has been a hotspot in this field for long time. This paper presents a new method about the retargetable assembler system design.It provides a kind of language CMDL, code mapping description language. During the process of assembling, assembler languages are firstly translated to CMDL, and then mapped to the machine codes. In an other word, CMDL is inserted between assembler languages and machine codes during the translation procedure. As a medium code, CMDL has a lot of features, such as high extraction, strong descript capabilities. It can describe almost all attributes of assembler languages. By breaking the direct mapping relationship between assembler languages and machine codes, the complexities of machine codes are hided to the users, therefore, the new retargetable assembler system has higher retargetable level by converting the mapping from assembler languages and machine codes to assembler languages and CMDL, and implementationof it becomes easier. Based on the new mapping system structure, a retargetable assemblersystem is developed. It proved the whole system has good retargetability and implantability.【關鍵詞】instruction set, symbol table, assembler, lexical analysis, retargetability
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
