Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
The LTP5901 and LTP5902 require little external circuitry, as the devices references,decoupling and power supply filtering are integrated. The LTP5901 and LTP5902 will bemodularly certified for operation in the United States (FCC), Canada (IC) and theEuropean Union (CE).
Abstract: Some power architectures require the power supply sequencer (or system manager) to controldownstream power MOSFETs to allow power to flow into branch circuits. This application note explains howsystem power sequencing and level shifting can be accomplished using a low-voltage system manager
Safety GuidelinesThis manual contains notices which you should observe to ensure your own personal safety, as well as toprotect the product and connected equipment. These notices are highlighted in the manual by a warningtriangle and are marked as follows according to the level of danger:
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel
Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to
enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements
include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O
configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a
simple solution when additional I/O is needed for ACPI power switches, sensors,
push buttons, LEDs, fans, etc.
The PCA9536 is an 8-pin CMOS device that provides 4 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. I/O expanders providea simple solution when additional I/O is needed for ACPI power switches, sensors,push buttons, LEDs, fans, etc.
The PCA9537 is a 10-pin CMOS device that provides 4 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution when additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
The PCA9538 is a 16-pin CMOS device that provides 8 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution when additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
