超級電容器又稱超大容量電容器、金電容、黃金電容、儲能電容、法拉電容、電化學電容器或雙電層電容器（英文名稱為EDLC，即Electric Double Layer Capacitors），是靠極化電解液
上傳時間： 2013-05-23
上傳用戶：gxmm
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling Capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上傳時間： 2013-10-15
上傳用戶：busterman
Abstract: Electrolytic Capacitors are notorious for short lifetimes in high-temperature applications such asLED light bulbs. The careful selection of these devices with proper interpretation of their specifications isessential to ensure that they do not compromise the life of the end product. This application notediscusses this problem with electrolytic Capacitors in LED light bulbs and provides an analysis that showshow it is possible to use electrolytics in such products.
上傳時間： 2013-11-17
上傳用戶：asdfasdfd
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and Capacitors.
上傳時間： 2014-01-03
上傳用戶：dongbaobao
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output Capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上傳時間： 2013-10-18
上傳用戶：avensy
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has adjustable frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic Capacitors.
上傳時間： 2014-12-24
上傳用戶：Pzj
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and Capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上傳時間： 2013-11-18
上傳用戶：ZJX5201314
One of the fi rst lessons in a basic electronics coursecovers the symbols for resistors, Capacitors, inductors,voltage sources and current sources. Althougheach symbol represents a functional component of areal-world circuit, only some of the symbols have directphysical counterparts. For instance, the three discretepassive devices—resistors, Capacitors, inductors—canbe picked off a shelf and placed on a real board muchas their symbolic analogs appear in a basic schematic.Likewise, while voltage sources have no direct 2-terminalanalog, a voltage source can be easily built with an offthe-shelf linear regulator.
上傳時間： 2013-11-24
上傳用戶：simonpeng
A recent trend in the design of portable devices has beento use ceramic Capacitors to filter DC/DC converter inputs.Ceramic Capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic Capacitors due to shortages oftantalum Capacitors.
上傳時間： 2013-11-05
上傳用戶：comer1123
Removing output Capacitors saves money and boardspace. Linear Technology’s OPTI-LOOPTM architectureallows you to use the output Capacitors of your choice andcompensate the control loop for optimum transientresponse and loop stability. Figure 1 shows the dramaticimprovement possible with the OPTI-LOOP architecture.With the improvement shown in Figure 1, less capacitance
上傳時間： 2013-12-15
上傳用戶：fanboynet
