The PCA9546A is a quad bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, or Channels. Any individualSCx/SDx Channel or combination of Channels can be selected, determined by thecontents of the programmable control register.
上傳時間： 2013-11-16
上傳用戶：cc1915
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or Channels. Only oneSCx/SDx Channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that Channel.
上傳時間： 2014-12-28
上傳用戶：270189020
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or Channels. Any individualSCx/SDx Channel or combination of Channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the Channels to be deselected as does the internalPower-on reset function.
上傳時間： 2013-10-13
上傳用戶：bakdesec
Cctt, "Covert Channel Tunneling Tool" - 顧名思義，這是一種隱藏通道工具。他提供幾種可行方法來實現允許在已被網絡訪問控制系統授權的數據流上創建并建立任意數據流傳輸信道。
標簽： Tunneling Channel Covert Cctt
上傳時間： 2014-01-13
上傳用戶：gxf2016
This an adaptive receiver for a direct-sequence spread spectrum (DS-SS) system over an AWGN Channel. The adaptive receiver block is modified from the LMS adaptive filter block in DSP Blockset. For DS-SS signal reception, the adaptive filter needs to have multi-rate operation. The input sample rate is equal to chip rate and the output is at symbol rate. Two rates are related by PG, processing gain
標簽： direct-sequence adaptive receiver spectrum
上傳時間： 2014-01-16
上傳用戶：D&L37
UWB Channel,802.15.3a建議的S_V信道
上傳時間： 2015-04-10
上傳用戶：784533221
This packet is a IS-95 baseband simulation for 1 data Channel of 9.6 KBps rate. The simulation is written for static Channel and AWGN noise. The packet include: 1) Packet Builder (Viterbi Encoding, Interleaver, PN generation) 2) Modulator (RRC filter) 3) Demodulator (Matched Filter, RAKE receiver) 4) Receiver (HD or SD) (Deinterleaver, Viterbi Decoder). You should run "Simulation.m" function that include all modules.
標簽： simulation baseband Channel packet
上傳時間： 2014-11-09
上傳用戶：hwl453472107
official uwb Channel model
標簽： official Channel model uwb
上傳時間： 2015-04-12
上傳用戶：jqy_china
The IEEE Multipath Channel block simulates an indoor UWB Channel as described in "A Channel Model for Ultrawideband Indoor Communications" by J.R. Foerster, M. Pendergrass and A.F. Molisch, November 2003, and attempts to incorporate the processes used in their MATLAB scripts.
標簽： Channel Multipath simulates described
上傳時間： 2015-05-08
上傳用戶：水中浮云
his folder contains the following files: 1. 02490rxP802-15_SG3a-Channel-Modeling-Subcommittee-Report-Final.doc: This is the final report of the Channel modeling sub-committee. 2. cmx_imr.csv (x=1, 2, 3, and 4) represent the files containing the actual 100 Channel realizations for CM1, CM2, CM3, and CM4. The columns are organized as (time, amp, time, amp,...) 3. cmx_imr_np.csv (x=1, 2, 3, and 4) represent the files containing the number of paths in each of the 100 multipath realizations. 4. cmx_imr.mat (x=1, 2, 3, and 4) are the .mat files that can be loaded directly into Matlab (TM). 5. *.m files are the Matlab (TM) files used to generate the various Channel realizations.
標簽： a-Channel-Modeling-Subcommittee-R following contains folder
上傳時間： 2013-12-21
上傳用戶：hxy200501
