Source that implements a Shell for Linux. Can accept at least 2 pipes and 3 sets of Commands.
標簽： implements Commands Source accept
上傳時間： 2013-12-09
上傳用戶：chenxichenyue
Linux console Commands for begginers
標簽： begginers Commands console Linux
上傳時間： 2014-06-15
上傳用戶：haohaoxuexi
TIMIT data base 2. Run following Matlab Commands to make sure the installation worked correctly:
標簽： installation correctly following Commands
上傳時間： 2017-07-20
上傳用戶：dave520l
Run following Matlab Commands to make sure the installation worked correctly. Unlike query function, filterdb does not load all waveforms to memory but returns filtered database object. This is useful when the resulting set of the query is too big to fit in memory. Consequent calls to read function can be made to read content of this filtered database object.
標簽： installation following correctly Commands
上傳時間： 2013-12-30
上傳用戶：ainimao
Practical Guide to Linux Commands.
標簽： Practical Commands Guide Linux
上傳時間： 2014-01-03
上傳用戶：lhc9102
Command Sheet for Vigor series routers. It describes many useful Commands which can t not be used directly from Web UI.
標簽： describes Commands Command routers
上傳時間： 2017-09-19
上傳用戶：2467478207
Commands TRF7960 rfid
上傳時間： 2017-09-26
上傳用戶：王楚楚
隨著計算機技術的迅猛發展，受其影響的儀器行業也發生了巨大的變革，即儀器的手動操作使用改為計算機控制自動測試。隨著自動測試技術和程控儀器的發展，除了要求物理硬件接口標準化外，也要求軟件控制標準化。 硬件方面，從20世紀50代自動測試概念建立起，經過初期專用接口、半專用接口到20世紀80年代中期才普及推廣開放式標準接口總線，如RS232串行通信接口總線、GPIB通用接口總線、PXI計算機外圍儀器系統總線、VXI塊式儀器系統總線等。 軟件方面，1987年6月頒布的IEEE488．2（程控儀器消息交換協議）標準首先解決了數據結構方面的問題，但仍將大量的器件語義留給設計者自由定義。1990年4月，國際上九家儀器公司在IEEE488．2基礎上提出了SCPI（Standard Commands for Programmable Instruments程控儀器標準命令），才使程控儀器器件數據和命令得到標準化。SCPI的總目標是縮短自動測試系統程序開發時間，保護儀器制造者和使用者雙方的硬、軟件投資，為儀器控制和數據利用提供廣泛兼容的編碼環境。 儀器接收到SCPI消息后進行響應：接收字符串消息、詞法分析、語法分析、中間代碼生成、優化和目標代碼生成，語法分析模塊的性能直接影響到程控執行效率。為了進一步簡化儀器內語法分析模塊、提高程控執行效率，本課題提出了在接口電路中加入解析模塊的思想，可將控制器發送到儀器的SCPI消息即復雜的ASCII碼字符串轉變為簡單的二進制代碼。采用此解析模塊將大大簡化儀器設計者的軟件工作，既能實現儀器語言標準化又能提高儀器對遠程 控制的響應速度，這在研究實驗室內的自制儀器時將是很有用的。 儀器接口有很多種，本課題主要討論了RS232和GPIB兩種接口。本設計中儀器接口板是獨立于儀器的，與儀器單獨使用微處理器，若要與儀器連接實現通信只需在兩微處理器之間進行通信即可，這樣做的目的是：一方面可以不影響儀器的設計和操作，一方面可以實現接口板的通用性和儀器的可換性。針對于RS232接口為一簡單接口，我先將工作重心放在軟件設計上，主要考慮怎樣把復雜的ASCII碼字符串解析為簡單的二進制代碼。針對于GPIB接口，軟件設計的主要部分已完成，再把工作重心放在硬件設計上，采用性價比更高的CPID實現GPIB接口芯片NAT9914。為了觀察解析結果還加入了LCD顯示。本設計在開發通用的、低價的儀器接口板方面做了一個有益的嘗試，為進一步的自動測試系統研究打下了基礎。 關鍵詞：儀器；SCPI；RS232接口；GPIB接口；CPLD
上傳時間： 2013-04-24
上傳用戶：Andy123456
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus Commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上傳時間： 2013-10-09
上傳用戶：3294322651
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send Commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上傳時間： 2013-10-11
上傳用戶：dianxin61
