this code is a simulator to simulate the paging system such as first come first service. the Comment in this code can help you to run it.
標簽： first simulator the simulate
上傳時間： 2014-01-03
上傳用戶：Late_Li
測試安全性代碼 /* * put your module Comment here * formatted with JxBeauty (c) johann.langhofer@nextra.at */
標簽： formatted langhofer JxBeauty Comment
上傳時間： 2013-12-29
上傳用戶：waitingfy
requirement for Comment of sip(session initiation protol)
標簽： requirement initiation Comment session
上傳時間： 2014-11-26
上傳用戶：Zxcvbnm
At can be given its arguments in a file. You can Comment out lines by preceding them with either # or - characters. This is an easy way to temporarily disable some commands. The CONTINUE-command is most useful at the end of the file. When this command is read, the file is started again from the beginning. You can use it situations where the machine is not shut down for the night and you want to run some commands every day.
標簽： can arguments preceding Comment
上傳時間： 2013-12-11
上傳用戶：comua
About FreeBSD Comment
上傳時間： 2017-06-09
上傳用戶：PresidentHuang
Programming language: Developed in Omnet++. Comment: The model implements the AntNet routing algorithm proposed in: G. Di Caro and M. Dorigo. AntNet: Distributed Stigmergetic Control for Communications Networks. Journal of Artificial Intelligence Research, 9:317-365, 1998. It reqires OMNeT++ 2.3 or later.
標簽： Programming implements Developed language
上傳時間： 2014-11-30
上傳用戶：nanfeicui
E-ten Glofiish X500+ Camera driver and application all Comment and documentation info on chines
標簽： documentation application and Glofiish
上傳時間： 2013-12-09
上傳用戶：tyler
This collection of circuits was worked out between June1991 and July of 1994. Most were designed at customerrequest or are derivatives of such efforts. All representsubstantial effort and, as such, are disseminated here forwider study and (hopefully) use.1 The examples areroughly arranged in categories including power conversion,transducer signal conditioning, amplifiers and signalgenerators. As always, reader Comment and questionsconcerning variants of the circuits shown may be addresseddirectly to the author.
上傳時間： 2013-11-15
上傳用戶：凌云御清風
STM32，5110液晶顯示聲納探魚器200KHz，帶電路圖，精確到厘米 MC34063升壓，大聲壓發射，實際板子上濾波電路沒要（電路圖上的濾波電阻電容電感沒焊，開路或者短路）。一般200KHz的換能器在水里面的耦合比較好，在空氣中發射出來的（或者接收的）強度很低。 用的MOSFET Relay，contact和release時間都可以做到很小，不過選的是比較低端器件，所以最近測量距離為70cm。 開源啦開源啦 架構為狀態機+任務流，Task都是放在函數指針數組里面的 Task分兩種，routine的和錯誤處理的 5110液晶的SPI用的DMA 基本上STM32和C語言高階的特征都用上了，稍微修改直接可以商用 Open Issue 偶爾會hardware fault或者memory fault，然后watchdog重啟， 應該比較好解決，仔細檢查下就好 有什么問題代碼的file Comment里面有我聯系地址 有能搞到好的器件也請知會我，多謝了 接下來準備把它裝到船模上，用以前四軸的那套東西，就看什么時候有時間了
上傳時間： 2013-10-28
上傳用戶：songyue1991
/* RSA Demo 1.0 版 * 版權所有 (C) 2004 趙春生 * 2004.04.25 * http://timw.yeah.net * http://timw.126.com * 本程序調用Miracl ver 4.82大數運算庫，詳見其附帶手冊。 * P,Q,N,D,E使用RSATool2生成。 */ 編譯提示： 一：將Project-Settings-Settings For(All Configuration)-C/C++中Category項的 Precompiled Headers設置成：Automatic use of precompiled headers（圖1）。 二：將ms32.lib添加到工程中（圖2）。 三：MIRACL是C庫。 extern "C" { #include "miracl.h" #include "mirdef.h" } #pragma Comment( lib, "ms32.lib" )
上傳時間： 2015-03-23
上傳用戶：leehom61
